My e30 turbo.
Moderator: martauto
-
Colonel Sanders
- Le Surrender Monkey.
- Posts: 1296
- Joined: Mon Aug 07, 2006 11:00 pm
- Location: guernsey.... i mean france munching on garlic and drinking wine with my children.
very nice karel!! 
-
Karel
- E30 Zone Newbie

- Posts: 69
- Joined: Fri Jul 27, 2007 11:00 pm
first testrun done !!
save as:
http://karel.whost.se/blandat/bmwturbo/ ... ning-1.AVI
time to hit the dyno next



save as:
http://karel.whost.se/blandat/bmwturbo/ ... ning-1.AVI
time to hit the dyno next



-
Karel
- E30 Zone Newbie

- Posts: 69
- Joined: Fri Jul 27, 2007 11:00 pm
so end of the dyno day..
790nm and 660hp
with bad cluch

790nm and 660hp
with bad cluch
-
Colonel Sanders
- Le Surrender Monkey.
- Posts: 1296
- Joined: Mon Aug 07, 2006 11:00 pm
- Location: guernsey.... i mean france munching on garlic and drinking wine with my children.
very nice mate, how much boost?
-
bmwsport
- E30 Zone Camper

- Posts: 1374
- Joined: Tue May 29, 2007 11:00 pm
- Location: Retford, Nottinghamshire
Nice figuresKarel wrote:so end of the dyno day..
790nm and 660hp![]()
with bad cluch
-
Karel
- E30 Zone Newbie

- Posts: 69
- Joined: Fri Jul 27, 2007 11:00 pm
rossle wrote:very nice mate, how much boost?
only 1.7bar.. but then the cluch started to fail so at 4500rpm i had 713nm @ wheels and at 6000 the cluch loost grip and just spun out to the rev limit..
the dyno dident get any good reading from the spinning cluch so the hp figures are a little blurry but
there should be around 800-850nm and 700-720hp. right now.. (in the engine)
so now a new cluch is orderd and i will book a new time for the dyno
-
e30_Turbo
- Boost Junkie
- Posts: 3158
- Joined: Mon Jan 10, 2005 11:00 pm
- Location: East Anglia
WOW!
That's huge power, nice.
I'm only running .9bar now and it's plenty quick enough for me, looking forward to 1.3bar very much!
What's the spec on your turbo?
Mines a H1C, 55/82 & 67/63 on a 18cm3 housing, I get boost from 2700rpms and full chat @ 3700rpms.
I'd also like to know what timing you are running as I'm starting to tune my sparks, fueling is safe but rich, running around 11-1 at full boost all the way to the red line. I'm running around 10' on boost and only hear a chirp of det around 4k when on boost, no issues after that.
My clutch is also starting to die, it's only spun the once, today, 3rd gear full boost, but have a 6 puk plate to fit.
I'll try to remember the video camera next time I go out for a spirited drive!
Thanks, Fozz.
That's huge power, nice.
I'm only running .9bar now and it's plenty quick enough for me, looking forward to 1.3bar very much!
What's the spec on your turbo?
Mines a H1C, 55/82 & 67/63 on a 18cm3 housing, I get boost from 2700rpms and full chat @ 3700rpms.
I'd also like to know what timing you are running as I'm starting to tune my sparks, fueling is safe but rich, running around 11-1 at full boost all the way to the red line. I'm running around 10' on boost and only hear a chirp of det around 4k when on boost, no issues after that.
My clutch is also starting to die, it's only spun the once, today, 3rd gear full boost, but have a 6 puk plate to fit.
I'll try to remember the video camera next time I go out for a spirited drive!
Thanks, Fozz.
-
Colonel Sanders
- Le Surrender Monkey.
- Posts: 1296
- Joined: Mon Aug 07, 2006 11:00 pm
- Location: guernsey.... i mean france munching on garlic and drinking wine with my children.
hey mark, i have a pretty good map for 1 bar that mattias sent me a while ago if you want it?
-
Karel
- E30 Zone Newbie

- Posts: 69
- Joined: Fri Jul 27, 2007 11:00 pm
fozzymonster wrote:WOW!
That's huge power, nice.
I'm only running .9bar now and it's plenty quick enough for me, looking forward to 1.3bar very much!
What's the spec on your turbo?
Mines a H1C, 55/82 & 67/63 on a 18cm3 housing, I get boost from 2700rpms and full chat @ 3700rpms.
I'd also like to know what timing you are running as I'm starting to tune my sparks, fueling is safe but rich, running around 11-1 at full boost all the way to the red line. I'm running around 10' on boost and only hear a chirp of det around 4k when on boost, no issues after that.
My clutch is also starting to die, it's only spun the once, today, 3rd gear full boost, but have a 6 puk plate to fit.
I'll try to remember the video camera next time I go out for a spirited drive!
Thanks, Fozz.
hey Fozz
the turbo im using is called kkk29.
i dont have the exakt spec on it here.. but i could check it out..
but it should be around 61mm in and 75mm out
i have 1.5 @ 3500rpm and 713nm (on wheels) @ 4500
do you mean the dwell time? then im using 5.0 on cranking and 3.0 on running
11.1 in afr is good.. 10 is to rich.. but as i always say better rich then broke
what ecu are u running?
-
Karel
- E30 Zone Newbie

- Posts: 69
- Joined: Fri Jul 27, 2007 11:00 pm
-
GrindCulture
- E30 Zone Addict

- Posts: 2955
- Joined: Mon Mar 03, 2008 11:00 pm
- Location: Exeter
This car is MAD! Love it
KKK supplied the turbos for the 2002 turbo too if I'm not mistaken
KKK supplied the turbos for the 2002 turbo too if I'm not mistaken
Not in E30s any more 
-
e30_Turbo
- Boost Junkie
- Posts: 3158
- Joined: Mon Jan 10, 2005 11:00 pm
- Location: East Anglia
Hey dude!rossle wrote:hey mark, i have a pretty good map for 1 bar that mattias sent me a while ago if you want it?
Hows you?
I have a timing map from Mattias he sent me a long time ago but I found it was very harsh and didn't go well when loaded up.
I had to take quite a few degress out on boost to stop pinking, however I've not tried it since the other bits ( IC, chargepipes ) have been added.
These bits seem to be the key to running lots of boost and safely.
Currently I'm running a flat 10' across the board but the engines seems a little flat, I feel there's much more power to find with some tweaking.
Send it over tho please, I'll see if it's the same as what I have already and it's always good to compare anyway!
Fozz.
-
e30_Turbo
- Boost Junkie
- Posts: 3158
- Joined: Mon Jan 10, 2005 11:00 pm
- Location: East Anglia
My dwells are 6 for cranking and 3 for running, I tried less but had spark blow out on boost.Karel wrote:hey Fozzfozzymonster wrote:WOW!
That's huge power, nice.
I'm only running .9bar now and it's plenty quick enough for me, looking forward to 1.3bar very much!
What's the spec on your turbo?
Mines a H1C, 55/82 & 67/63 on a 18cm3 housing, I get boost from 2700rpms and full chat @ 3700rpms.
I'd also like to know what timing you are running as I'm starting to tune my sparks, fueling is safe but rich, running around 11-1 at full boost all the way to the red line. I'm running around 10' on boost and only hear a chirp of det around 4k when on boost, no issues after that.
My clutch is also starting to die, it's only spun the once, today, 3rd gear full boost, but have a 6 puk plate to fit.
I'll try to remember the video camera next time I go out for a spirited drive!
Thanks, Fozz.
the turbo im using is called kkk29.
i dont have the exakt spec on it here.. but i could check it out..
but it should be around 61mm in and 75mm out
i have 1.5 @ 3500rpm and 713nm (on wheels) @ 4500
do you mean the dwell time? then im using 5.0 on cranking and 3.0 on running
11.1 in afr is good.. 10 is to rich.. but as i always say better rich then broke
what ecu are u running?
I'm running a MS v3 with wasted sparks and provision for boost control and water injection.
My AFRS stay around 11-1 but do drop into the high 10's when over 5000rpms! I'll lean it off on the dyno, like you say, better rich than broke! And I've already broken it a fair few times
Here's my setup:

-
e30-320i
- E30 Zone Regular

- Posts: 518
- Joined: Fri May 27, 2005 11:00 pm
- Location: suffolk
Damn that's one quick e30 and road legal too.I don't know how you guys do it hats off to you 

89 325i touring
-
Colonel Sanders
- Le Surrender Monkey.
- Posts: 1296
- Joined: Mon Aug 07, 2006 11:00 pm
- Location: guernsey.... i mean france munching on garlic and drinking wine with my children.
you done done well karel...
should be getting my motor in this week..
should be getting my motor in this week..
-
Karel
- E30 Zone Newbie

- Posts: 69
- Joined: Fri Jul 27, 2007 11:00 pm
rossle wrote:you done done well karel...
should be getting my motor in this week..
Thanks Sean.
are u gonna run with o-ringed block?
-
Colonel Sanders
- Le Surrender Monkey.
- Posts: 1296
- Joined: Mon Aug 07, 2006 11:00 pm
- Location: guernsey.... i mean france munching on garlic and drinking wine with my children.
yes i had had the cylinder head oringed and the coolent channels welded, my block was too expencive to send away too.
what times do you think you will get down the drag strip with your new motor then?
what times do you think you will get down the drag strip with your new motor then?
-
Karel
- E30 Zone Newbie

- Posts: 69
- Joined: Fri Jul 27, 2007 11:00 pm
rossle wrote:yes i had had the cylinder head oringed and the coolent channels welded, my block was too expencive to send away too.
what times do you think you will get down the drag strip with your new motor then?
ah okay!! thats a samrt move !!
are u gonna run the original gasket ?
well im gonna try the car on the roads this friday.. theres a little race here in town
but i think that end of this month i should have atleast tryied it on the strip once
-
Karel
- E30 Zone Newbie

- Posts: 69
- Joined: Fri Jul 27, 2007 11:00 pm
some pictures my friend took of the car yesterday 
















-
Colonel Sanders
- Le Surrender Monkey.
- Posts: 1296
- Joined: Mon Aug 07, 2006 11:00 pm
- Location: guernsey.... i mean france munching on garlic and drinking wine with my children.
that looks sweet mate, have you still got an open dump pipe from the wastegate?
yeah im still gonna run the original gasket, with your old pistons and rods, il only take mine to around 1.3 BAR,
should be fun....
what diff are you running now? have you moved to a 535 diff?
yeah im still gonna run the original gasket, with your old pistons and rods, il only take mine to around 1.3 BAR,
should be fun....
what diff are you running now? have you moved to a 535 diff?
-
enginbaba
- E30 Zone Newbie

- Posts: 11
- Joined: Mon Jun 30, 2008 11:00 pm
- Location: Manchester
The engine does not work properly, u should check it up some time as u can hear from the exhaust sound.
-
toughguych
- E30 Zone Newbie

- Posts: 211
- Joined: Sat Feb 19, 2005 11:00 pm
- Location: Channel Islands
Fuck me, You got that biatch running on kanga juice?
Up date?
Up date?
-
Karel
- E30 Zone Newbie

- Posts: 69
- Joined: Fri Jul 27, 2007 11:00 pm
enginbaba wrote:The engine does not work properly, u should check it up some time as u can hear from the exhaust sound.
what do you mean ?
-
Karel
- E30 Zone Newbie

- Posts: 69
- Joined: Fri Jul 27, 2007 11:00 pm
toughguych wrote:**** me, You got that biatch running on kanga juice?
Up date?
hhehe no just e85
-
Karel
- E30 Zone Newbie

- Posts: 69
- Joined: Fri Jul 27, 2007 11:00 pm
time for some updates 
small ones this time.
Bmw vs Kleeman Slk
Bmw vs Singel turbo supra
enjoy
ps. a movie from gatebil track day will be done soon
small ones this time.
Bmw vs Kleeman Slk
Bmw vs Singel turbo supra
enjoy
ps. a movie from gatebil track day will be done soon
-
Flozman
- E30 Zone Newbie

- Posts: 239
- Joined: Sat Jun 21, 2008 11:00 pm
- Location: Andover
Hi Karel,
Great stuff, you should come over to England ill give you a run.
Great stuff, you should come over to England ill give you a run.

-
Karel
- E30 Zone Newbie

- Posts: 69
- Joined: Fri Jul 27, 2007 11:00 pm
hehe yeah if there was a bridge between norway and england i couldFlozman wrote:Hi Karel,
Great stuff, you should come over to England ill give you a run.
but its faar away
what do you drive?
-
E30BeemerLad
- Married to the E30 Zone

- Posts: 16806
- Joined: Mon Mar 28, 2005 11:00 pm
- Location: Norfolk
mate that's a beast! 
-
Karel
- E30 Zone Newbie

- Posts: 69
- Joined: Fri Jul 27, 2007 11:00 pm
thanks !!
here`s another one.. this is from the hole race
here`s another one.. this is from the hole race
-
Karel
- E30 Zone Newbie

- Posts: 69
- Joined: Fri Jul 27, 2007 11:00 pm
so the first pass on the drag strip is done.
10.41/220kmh on only 1.5 bars of boost.
the car i dynoed ad 2bar
so for the next year the goal is to break the 9sek
10.41/220kmh on only 1.5 bars of boost.
the car i dynoed ad 2bar
so for the next year the goal is to break the 9sek
-
Colonel Sanders
- Le Surrender Monkey.
- Posts: 1296
- Joined: Mon Aug 07, 2006 11:00 pm
- Location: guernsey.... i mean france munching on garlic and drinking wine with my children.
cheers for the text last night karel, didnt see it till this morning...
thats awesome, and the vids look good too.. you launch it hard!!!!!!!
thats awesome, and the vids look good too.. you launch it hard!!!!!!!
