Compression test results - also high idle issue

Need technical Q/A then you're in the right place

Moderator: martauto

JazzMan
E30 Zone Camper
E30 Zone Camper
Posts: 1070
Joined: Sat Mar 26, 2005 11:00 pm
Location: Deep South

Post Wed Feb 14, 2007 8:10 pm

I just did a compression test on my M20 - 4 revolutions each:

1: 12.5 bar
2: 12.5 bar
3: 12.5 bar
4: 12 bar
5: 12.25 bar
6: 12 bar

In PSI (from google)
1: 181.3
2: 181.3
3: 181.3
4: 174
5: 177.7
6: 174

Is that good/bad? As I understand it they should ideally all be the same?

Plugs are sooty / black so it looks like its overfuelling according to the bentley manual.

It's also idling high (1000-1100 rpm) and I've done all the usual vacuum leak tests, ICV clean, AFM clean, tried new AFM, ICV, changed the ECU chip for a zone wild, TPS switch test, clean out and adjustment, blue sensor swap. It also has a BBTB, its got a new cam belt, dizzy cap and rotor, new plugs (gap checked).

I think I'm going to try and clean the injectors as bentley manual suggested this as a problem. Any other ideas?
Turbo-Brown
Boost Junkie
Posts: 4705
Joined: Tue Feb 15, 2005 11:00 pm
Location: Aldershot, Hants

Post Wed Feb 14, 2007 9:11 pm

Think your compression results are fine myself, well withing 10% of eachother :D

No idea about the idle probs though. Not something simple like the cable being tight?
325i Twin Turbo (until 10am 01/12/07 :( )

www.air-in.co.uk free M20 exhaust and inlet flange
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Wed Feb 14, 2007 9:22 pm

Compression test results are absolutely fine.
Don't know the specs of Ant's"wild" chip, but I would expect a high idle to be one of it's characteristics.
I would have thought that this chip is only suitable for use with an engine that has mods to make it breath better (cam, etc), so this may be your problem.
JazzMan
E30 Zone Camper
E30 Zone Camper
Posts: 1070
Joined: Sat Mar 26, 2005 11:00 pm
Location: Deep South

Post Wed Feb 14, 2007 9:27 pm

It does it on a the normal chip too, I only put it in to see if it would make a difference.

Good news on the compression :)

I plan on putting a cam in, but I wanted to sort the idle first! :)

EDIT: Will get a multimeter out and try and check all the electrical connections. I did change the injector / temp sensor plug under the inlet manifold for new connectors / pins as it was seriously corroded.
User avatar
reggid
E30 Zone Squatter
E30 Zone Squatter
Posts: 1984
Joined: Mon Jul 11, 2005 11:00 pm
Location: Oz

Post Thu Feb 15, 2007 1:44 am

IIRC with compression test results its not about the absolute numbers so as long as they are similar cross all cylinders as various things can affect the absolute numbers such as temp, cam duration and cam timing, cranking speed etc.
The bentley spec says 145psi to 165psi so if you numbers are belwo those there may be a problem but as i siad its more about consistancy. What are the specs of your m20 engine?
JazzMan
E30 Zone Camper
E30 Zone Camper
Posts: 1070
Joined: Sat Mar 26, 2005 11:00 pm
Location: Deep South

Post Thu Feb 15, 2007 8:11 am

The engine is from a 1988 325i Touring - all internals stock (as far as I am aware, I didn't get any history with the car) :)
User avatar
pnd
E30 Zone Squatter
E30 Zone Squatter
Posts: 1801
Joined: Sat Nov 12, 2005 11:00 pm

Post Thu Feb 15, 2007 10:13 am

if you put a cam in the idle normally drops below the ideal I know it sounds like a bodge but put the cam in and it may idle about right.
kam-325i
E30 Zone Team Member
E30 Zone Team Member
Posts: 4851
Joined: Tue Sep 27, 2005 11:00 pm
Location: TELFORD !!!! (Shropshire) Stevetigger Land !!!

Post Thu Feb 15, 2007 10:32 pm

Compression is fine.
Spec is a Minimum of 10bar and each cylinder +/- 10%
Pete don't care about colour, He would shag a rainbow if he could find the end of it....
Image
JazzMan
E30 Zone Camper
E30 Zone Camper
Posts: 1070
Joined: Sat Mar 26, 2005 11:00 pm
Location: Deep South

Post Thu Feb 15, 2007 10:37 pm

kam-325i wrote:Compression is fine.
Spec is a Minimum of 10bar and each cylinder +/- 10%
Excellent :)
pnd wrote:if you put a cam in the idle normally drops below the ideal I know it sounds like a bodge but put the cam in and it may idle about right.
Dunno seems like fixing the wrong problem! But you never know :)

I'm guessing its probably something really simple I've been overlooking!
JazzMan
E30 Zone Camper
E30 Zone Camper
Posts: 1070
Joined: Sat Mar 26, 2005 11:00 pm
Location: Deep South

Post Sat Feb 17, 2007 5:55 pm

I pulled the injectors out today and the o-rings pretty much fell to pieces after prodding them a bit. So I'm guessing I will have has a vacuum leak from there.

Also one of the injectors wasn't spraying as well as the others. Put them in the in the ultra sonic cleaner for a good while. Unfortunately my local parts desk was closed by the time I needed new o-rings so running will have to wait until I get new ones!