I just did a compression test on my M20 - 4 revolutions each:
1: 12.5 bar
2: 12.5 bar
3: 12.5 bar
4: 12 bar
5: 12.25 bar
6: 12 bar
In PSI (from google)
1: 181.3
2: 181.3
3: 181.3
4: 174
5: 177.7
6: 174
Is that good/bad? As I understand it they should ideally all be the same?
Plugs are sooty / black so it looks like its overfuelling according to the bentley manual.
It's also idling high (1000-1100 rpm) and I've done all the usual vacuum leak tests, ICV clean, AFM clean, tried new AFM, ICV, changed the ECU chip for a zone wild, TPS switch test, clean out and adjustment, blue sensor swap. It also has a BBTB, its got a new cam belt, dizzy cap and rotor, new plugs (gap checked).
I think I'm going to try and clean the injectors as bentley manual suggested this as a problem. Any other ideas?
Compression test results - also high idle issue
Moderator: martauto
-
JazzMan
- E30 Zone Camper

- Posts: 1070
- Joined: Sat Mar 26, 2005 11:00 pm
- Location: Deep South
-
Turbo-Brown
- Boost Junkie
- Posts: 4705
- Joined: Tue Feb 15, 2005 11:00 pm
- Location: Aldershot, Hants
Think your compression results are fine myself, well withing 10% of eachother 
No idea about the idle probs though. Not something simple like the cable being tight?
No idea about the idle probs though. Not something simple like the cable being tight?
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
Compression test results are absolutely fine.
Don't know the specs of Ant's"wild" chip, but I would expect a high idle to be one of it's characteristics.
I would have thought that this chip is only suitable for use with an engine that has mods to make it breath better (cam, etc), so this may be your problem.
Don't know the specs of Ant's"wild" chip, but I would expect a high idle to be one of it's characteristics.
I would have thought that this chip is only suitable for use with an engine that has mods to make it breath better (cam, etc), so this may be your problem.
-
JazzMan
- E30 Zone Camper

- Posts: 1070
- Joined: Sat Mar 26, 2005 11:00 pm
- Location: Deep South
It does it on a the normal chip too, I only put it in to see if it would make a difference.
Good news on the compression
I plan on putting a cam in, but I wanted to sort the idle first!
EDIT: Will get a multimeter out and try and check all the electrical connections. I did change the injector / temp sensor plug under the inlet manifold for new connectors / pins as it was seriously corroded.
Good news on the compression
I plan on putting a cam in, but I wanted to sort the idle first!
EDIT: Will get a multimeter out and try and check all the electrical connections. I did change the injector / temp sensor plug under the inlet manifold for new connectors / pins as it was seriously corroded.
-
reggid
- E30 Zone Squatter

- Posts: 1984
- Joined: Mon Jul 11, 2005 11:00 pm
- Location: Oz
IIRC with compression test results its not about the absolute numbers so as long as they are similar cross all cylinders as various things can affect the absolute numbers such as temp, cam duration and cam timing, cranking speed etc.
The bentley spec says 145psi to 165psi so if you numbers are belwo those there may be a problem but as i siad its more about consistancy. What are the specs of your m20 engine?
The bentley spec says 145psi to 165psi so if you numbers are belwo those there may be a problem but as i siad its more about consistancy. What are the specs of your m20 engine?
-
JazzMan
- E30 Zone Camper

- Posts: 1070
- Joined: Sat Mar 26, 2005 11:00 pm
- Location: Deep South
The engine is from a 1988 325i Touring - all internals stock (as far as I am aware, I didn't get any history with the car) 
-
pnd
- E30 Zone Squatter

- Posts: 1801
- Joined: Sat Nov 12, 2005 11:00 pm
if you put a cam in the idle normally drops below the ideal I know it sounds like a bodge but put the cam in and it may idle about right.
-
kam-325i
- E30 Zone Team Member

- Posts: 4851
- Joined: Tue Sep 27, 2005 11:00 pm
- Location: TELFORD !!!! (Shropshire) Stevetigger Land !!!
Compression is fine.
Spec is a Minimum of 10bar and each cylinder +/- 10%
Spec is a Minimum of 10bar and each cylinder +/- 10%
Pete don't care about colour, He would shag a rainbow if he could find the end of it....


-
JazzMan
- E30 Zone Camper

- Posts: 1070
- Joined: Sat Mar 26, 2005 11:00 pm
- Location: Deep South
Excellentkam-325i wrote:Compression is fine.
Spec is a Minimum of 10bar and each cylinder +/- 10%
Dunno seems like fixing the wrong problem! But you never knowpnd wrote:if you put a cam in the idle normally drops below the ideal I know it sounds like a bodge but put the cam in and it may idle about right.
I'm guessing its probably something really simple I've been overlooking!
-
JazzMan
- E30 Zone Camper

- Posts: 1070
- Joined: Sat Mar 26, 2005 11:00 pm
- Location: Deep South
I pulled the injectors out today and the o-rings pretty much fell to pieces after prodding them a bit. So I'm guessing I will have has a vacuum leak from there.
Also one of the injectors wasn't spraying as well as the others. Put them in the in the ultra sonic cleaner for a good while. Unfortunately my local parts desk was closed by the time I needed new o-rings so running will have to wait until I get new ones!
Also one of the injectors wasn't spraying as well as the others. Put them in the in the ultra sonic cleaner for a good while. Unfortunately my local parts desk was closed by the time I needed new o-rings so running will have to wait until I get new ones!

