Filling the voids in subframe bushes ?
Moderator: martauto
-
Andy335Touring
- Married to the E30 Zone

- Posts: 7144
- Joined: Sun Jan 09, 2005 11:00 pm
- Location: Long Eaton,Nottingham
First off i'd like say what effect i'm trying to get and what i have fitted now, i want a subframe bush thats stiffer than a stock rubber bush but with out the down sides of using polly bushes.
I have some genuine BMW rubber bushes that were fitted about 15mths ago, i find that i have too much wheel hop when i try to move off quickly from a standing start and i feel the car isn't or doesn't feel as planted as it should do.
To strengthen the bushes in situ i was thinking of using a product by 3M. One cartridge should be plenty to do both subframe bushes and with the left overs i could fill my diff bush may be ?
If you google "Windo-weld" you will see that it crops up quite a bit on US and ricer forums for filling various bushes, all the threads i've read have pretty much been filled with positive results. It's hardness is supposed to be more like hard rubber rather than urethane.
The plan is as my bushes are fairly new i will remove the lower metal bush cup/washer thingy and as the stuff comes in a caulking tube i will push the tip as far into the bush voids as posible and fill it up. Put some foil on the bush cup/washer thingy so they don't get stuck on to the bush.
Should i fill the bush with the wheel on a ramp or block so the bush is sitting in it's normal place ?
Reading some of the threads this stuff can take up to 48 hrs to properly cure depending on how thick it's applied. As the bush cup/washer thingy is going back on it's not going to be exposed to the air so i'm going to use some heat to help cure it.
Obviously if you were going to replace the bushes any way, you would just fill them up ready before hand but doing it in situ makes it more difficult.
So, what do you think of this idea ?
Do you think i will achieve a decent improvment by doing this ?
I have some genuine BMW rubber bushes that were fitted about 15mths ago, i find that i have too much wheel hop when i try to move off quickly from a standing start and i feel the car isn't or doesn't feel as planted as it should do.
To strengthen the bushes in situ i was thinking of using a product by 3M. One cartridge should be plenty to do both subframe bushes and with the left overs i could fill my diff bush may be ?
If you google "Windo-weld" you will see that it crops up quite a bit on US and ricer forums for filling various bushes, all the threads i've read have pretty much been filled with positive results. It's hardness is supposed to be more like hard rubber rather than urethane.
The plan is as my bushes are fairly new i will remove the lower metal bush cup/washer thingy and as the stuff comes in a caulking tube i will push the tip as far into the bush voids as posible and fill it up. Put some foil on the bush cup/washer thingy so they don't get stuck on to the bush.
Should i fill the bush with the wheel on a ramp or block so the bush is sitting in it's normal place ?
Reading some of the threads this stuff can take up to 48 hrs to properly cure depending on how thick it's applied. As the bush cup/washer thingy is going back on it's not going to be exposed to the air so i'm going to use some heat to help cure it.
Obviously if you were going to replace the bushes any way, you would just fill them up ready before hand but doing it in situ makes it more difficult.
So, what do you think of this idea ?
Do you think i will achieve a decent improvment by doing this ?
-
Speedtouch
- Old Skooler

- Posts: 14130
- Joined: Tue Feb 14, 2006 11:00 pm
- Location: Canterbury
It's a nice variant on the 'silicone sealant' bushes commonly used to bodge iffy bushes through the MOT! 
///M aurice
ECU Upgrade EPROM Chips, £40 posted within the UK. Note these are not Zone chips.
viewtopic.php?f=6&t=279421
ECU Upgrade EPROM Chips, £40 posted within the UK. Note these are not Zone chips.
viewtopic.php?f=6&t=279421
-
gareth
- E30 Zone Team Member

- Posts: 11005
- Joined: Tue Jan 11, 2005 11:00 pm
- Location: hastings, east sussex
worth a go i guess. i suspect the curing times for the rear could be drastically longer due to the very restricted airflow and visible area on the material you add. maybe pulling the caps off when you're done and the car is on the ground would help it a bit, just don't drive away!!!!
operation test-pilot commences here!
operation test-pilot commences here!
Sole founder of Fe2O3-12V it's a lifestyle

LSD rebuilding / modification services provided, PM for details

LSD rebuilding / modification services provided, PM for details
-
bigdek
- E30 Zone Camper

- Posts: 1115
- Joined: Thu Feb 10, 2005 11:00 pm
- Location: Fife Scotland
just kidding m8.
guess u can only try it
guess u can only try it
-
DRIFTBOY
- E30 Zone Addict

- Posts: 3131
- Joined: Mon May 22, 2006 11:00 pm
- Location: Kent
I've not really finding any downsides to having poly bushes and I'm quite impressed with mine. I've not driven an E30 hard with good standard bushes though, is there really that much of a downside to poly ones?
I've heard a few people say they don't like them.
Just interested to hear your valued opinion really.
Thanks,
Martin.
I've heard a few people say they don't like them.
Just interested to hear your valued opinion really.
Thanks,
Martin.
Jeremy Clarkson wrote:...but it drives the front wheels. Theee wrooong wheels!
da4x4turbo wrote:I raced a vivaro on the motorway once in a 318is.... and lost!!!
-
Andy335Touring
- Married to the E30 Zone

- Posts: 7144
- Joined: Sun Jan 09, 2005 11:00 pm
- Location: Long Eaton,Nottingham
Mmm, i wonder if the best way is to leave the caps off like you say, have it on axle stands with a jack on the subframe to make sure the bushes are roughly compressed as much as if the car was sitting on it's wheels ??gareth wrote:worth a go i guess. i suspect the curing times for the rear could be drastically longer due to the very restricted airflow and visible area on the material you add. maybe pulling the caps off when you're done and the car is on the ground would help it a bit, just don't drive away!!!!
-
Andy335Touring
- Married to the E30 Zone

- Posts: 7144
- Joined: Sun Jan 09, 2005 11:00 pm
- Location: Long Eaton,Nottingham
TBH I don't have any first hand experiance with poly bushes, i'm going on what i've read on here really.DRIFTBOY wrote:I've not really finding any downsides to having poly bushes and I'm quite impressed with mine. I've not driven an E30 hard with good standard bushes though, is there really that much of a downside to poly ones?
I've heard a few people say they don't like them.
Just interested to hear your valued opinion really.
Thanks,
Martin.
Did you notice any extra noise or did the bumps seem more crashy/harsh when you changed over ?
-
Andy335Touring
- Married to the E30 Zone

- Posts: 7144
- Joined: Sun Jan 09, 2005 11:00 pm
- Location: Long Eaton,Nottingham
LOL, cheers Dbigdek wrote:just kidding m8.
guess u can only try it
-
gareth
- E30 Zone Team Member

- Posts: 11005
- Joined: Tue Jan 11, 2005 11:00 pm
- Location: hastings, east sussex
don't do that jack the car from the subframe, it'll trash your bushes! if you think about it, the weight of the car doesn't sit on the subframe at all... the rear of the car is suported on the springs which sit on the trailing arms. little load passes though the subframe.Andy335Touring wrote:Mmm, i wonder if the best way is to leave the caps off like you say, have it on axle stands with a jack on the subframe to make sure the bushes are roughly compressed as much as if the car was sitting on it's wheels ??gareth wrote:worth a go i guess. i suspect the curing times for the rear could be drastically longer due to the very restricted airflow and visible area on the material you add. maybe pulling the caps off when you're done and the car is on the ground would help it a bit, just don't drive away!!!!
why not jack up, pull off the caps, pump in the goo, refit the caps, drop onto the floor, drive about a bit to settle things, remove the caps... that'll replicate the loaded state best.
Sole founder of Fe2O3-12V it's a lifestyle

LSD rebuilding / modification services provided, PM for details

LSD rebuilding / modification services provided, PM for details
-
Andy325i
- E30 Zone Addict

- Posts: 4052
- Joined: Mon Jan 10, 2005 11:00 pm
- Location: Avon
Just my 2P worth:Andy335Touring wrote:
Did you notice any extra noise or did the bumps seem more crashy/harsh when you changed over ?
I fitted polly subframe bushes and didn't notice any more road noise etc, just slighty more responsive. On the subject of polly bushes on the rear of the front arms are well worth doing
Andy
Last edited by Andy325i on Mon Feb 12, 2007 10:07 pm, edited 1 time in total.

M50B25NonVanos & M52B28Vanos Heads for sale. Pm Me.
-
Andy335Touring
- Married to the E30 Zone

- Posts: 7144
- Joined: Sun Jan 09, 2005 11:00 pm
- Location: Long Eaton,Nottingham
Bollox, i thought it was OK, this might be my problemgareth wrote:
don't do that jack the car from the subframe, it'll trash your bushes!
-
Andy335Touring
- Married to the E30 Zone

- Posts: 7144
- Joined: Sun Jan 09, 2005 11:00 pm
- Location: Long Eaton,Nottingham
Cheers for your feed back mateAndy325i wrote:
I fitted polly subframe bushes and didn't notice any more road noise etc, just slighty more responsive.
Andy
How is your conversion going ?
-
oze30
- E30 Zone Addict

- Posts: 4133
- Joined: Mon Oct 24, 2005 11:00 pm
- Location: Sydney
There's a company in the states that makes stainless steel or metal bushes. They replace the rubber/poly ones with solid metal. They say its for race only..
-
Andy325i
- E30 Zone Addict

- Posts: 4052
- Joined: Mon Jan 10, 2005 11:00 pm
- Location: Avon
No worries 
which one mate? The 2.8?
All good ta, but saving for a more sensible diff/rear end atm
Not sure if I am going to go E36/ E30 M3 for the 5 stud conversion yet
Andy
which one mate? The 2.8?
All good ta, but saving for a more sensible diff/rear end atm
Not sure if I am going to go E36/ E30 M3 for the 5 stud conversion yet
Andy

M50B25NonVanos & M52B28Vanos Heads for sale. Pm Me.
-
Andy335Touring
- Married to the E30 Zone

- Posts: 7144
- Joined: Sun Jan 09, 2005 11:00 pm
- Location: Long Eaton,Nottingham
Yeah, i've seen almost every E30 bush made in metal, like you say, track only reallyoze30 wrote:There's a company in the states that makes stainless steel or metal bushes. They replace the rubber/poly ones with solid metal. They say its for race only..
-
Andy335Touring
- Married to the E30 Zone

- Posts: 7144
- Joined: Sun Jan 09, 2005 11:00 pm
- Location: Long Eaton,Nottingham
Cool, glad it's(2.8 ) going well, whats the other project ?Andy325i wrote:No worries
which one mate? The 2.8?
All good ta, but saving for a more sensible diff/rear end atm
Not sure if I am going to go E36/ E30 M3 for the 5 stud conversion yet![]()
Andy
I'd love to go 5 stud but it's not cheap is it with wheels/tyres/etc
-
Andy325i
- E30 Zone Addict

- Posts: 4052
- Joined: Mon Jan 10, 2005 11:00 pm
- Location: Avon
I can't possibly say yet (only in the planning atm) but all will be revealed I promiseAndy335Touring wrote:
whats the other project ?
I'd love to go 5 stud but it's not cheap is it with wheels/tyres/etc
Yep know what you mean about the 5 stud being expensive, but imho it offers a far better range of wheels etc weather it be E30 M3 or E36 route
Andy

M50B25NonVanos & M52B28Vanos Heads for sale. Pm Me.
-
Andy335Touring
- Married to the E30 Zone

- Posts: 7144
- Joined: Sun Jan 09, 2005 11:00 pm
- Location: Long Eaton,Nottingham
yer big tease
<edit> LOL, how
does that sound !

<edit> LOL, how
-
gareth
- E30 Zone Team Member

- Posts: 11005
- Joined: Tue Jan 11, 2005 11:00 pm
- Location: hastings, east sussex
most E30's have had this done over the years. as the bottom of the diff looks so tempting and it's a pain to do otherwise.Andy335Touring wrote:Bollox, i thought it was OK, this might be my problemgareth wrote:
don't do that jack the car from the subframe, it'll trash your bushes!
if you look at the subframe bushes while you jack from the subframe you'll see them getting stretched to hell! there wa a big argument on here a while ago with people saying that i must be wrong as it's ok on a subaru etc etc etc but not on a E30 as the weight is simply not designed to pass though there and the diff bush.
oh well, at least they're cheap... just a pig to swap!
Sole founder of Fe2O3-12V it's a lifestyle

LSD rebuilding / modification services provided, PM for details

LSD rebuilding / modification services provided, PM for details
-
DRIFTBOY
- E30 Zone Addict

- Posts: 3131
- Joined: Mon May 22, 2006 11:00 pm
- Location: Kent
I didn't notice them being harsh or noisy in any way, even with no soundproofing at all (just carpet), as Andy325i said, I only noticed a positive result. And they are really easy to fit - once the old bushes are out!Andy335Touring wrote:TBH I don't have any first hand experiance with poly bushes, i'm going on what i've read on here really.DRIFTBOY wrote:I've not really finding any downsides to having poly bushes and I'm quite impressed with mine. I've not driven an E30 hard with good standard bushes though, is there really that much of a downside to poly ones?
I've heard a few people say they don't like them.
Just interested to hear your valued opinion really.
Thanks,
Martin.
Did you notice any extra noise or did the bumps seem more crashy/harsh when you changed over ?
Jeremy Clarkson wrote:...but it drives the front wheels. Theee wrooong wheels!
da4x4turbo wrote:I raced a vivaro on the motorway once in a 318is.... and lost!!!
-
Andy335Touring
- Married to the E30 Zone

- Posts: 7144
- Joined: Sun Jan 09, 2005 11:00 pm
- Location: Long Eaton,Nottingham
Cheers for the help/info chaps
Not sure now, i might just pack them out with this Window seal stuff and see how i get on(easy and cheap), if thats no good then i'll use some proper polly bushes(ball ache and more £Â£Ã‚£).
Not sure now, i might just pack them out with this Window seal stuff and see how i get on(easy and cheap), if thats no good then i'll use some proper polly bushes(ball ache and more £Â£Ã‚£).
-
DRIFTBOY
- E30 Zone Addict

- Posts: 3131
- Joined: Mon May 22, 2006 11:00 pm
- Location: Kent
Sounds like a good plan!Andy335Touring wrote:Cheers for the help/info chaps![]()
Not sure now, i might just pack them out with this Window seal stuff and see how i get on(easy and cheap), if thats no good then i'll use some proper polly bushes(ball ache and more £Â£Ã‚£).
But please let us all know if it works or not - you could be on to something!
Jeremy Clarkson wrote:...but it drives the front wheels. Theee wrooong wheels!
da4x4turbo wrote:I raced a vivaro on the motorway once in a 318is.... and lost!!!
