Filling the voids in subframe bushes ?

Need technical Q/A then you're in the right place

Moderator: martauto

Andy335Touring
Married to the E30 Zone
Married to the E30 Zone
Posts: 7144
Joined: Sun Jan 09, 2005 11:00 pm
Location: Long Eaton,Nottingham

Post Mon Feb 12, 2007 9:15 pm

First off i'd like say what effect i'm trying to get and what i have fitted now, i want a subframe bush thats stiffer than a stock rubber bush but with out the down sides of using polly bushes.

I have some genuine BMW rubber bushes that were fitted about 15mths ago, i find that i have too much wheel hop when i try to move off quickly from a standing start and i feel the car isn't or doesn't feel as planted as it should do.

To strengthen the bushes in situ i was thinking of using a product by 3M. One cartridge should be plenty to do both subframe bushes and with the left overs i could fill my diff bush may be ?



If you google "Windo-weld" you will see that it crops up quite a bit on US and ricer forums for filling various bushes, all the threads i've read have pretty much been filled with positive results. It's hardness is supposed to be more like hard rubber rather than urethane.

The plan is as my bushes are fairly new i will remove the lower metal bush cup/washer thingy and as the stuff comes in a caulking tube i will push the tip as far into the bush voids as posible and fill it up. Put some foil on the bush cup/washer thingy so they don't get stuck on to the bush.

Should i fill the bush with the wheel on a ramp or block so the bush is sitting in it's normal place ?

Reading some of the threads this stuff can take up to 48 hrs to properly cure depending on how thick it's applied. As the bush cup/washer thingy is going back on it's not going to be exposed to the air so i'm going to use some heat to help cure it.

Obviously if you were going to replace the bushes any way, you would just fill them up ready before hand but doing it in situ makes it more difficult.

So, what do you think of this idea ?

Do you think i will achieve a decent improvment by doing this ?
Speedtouch
Old Skooler
Old Skooler
Posts: 14130
Joined: Tue Feb 14, 2006 11:00 pm
Location: Canterbury

Post Mon Feb 12, 2007 9:23 pm

It's a nice variant on the 'silicone sealant' bushes commonly used to bodge iffy bushes through the MOT! :wink:
///M aurice
ECU Upgrade EPROM Chips, £40 posted within the UK. Note these are not Zone chips.
viewtopic.php?f=6&t=279421
bigdek
E30 Zone Camper
E30 Zone Camper
Posts: 1115
Joined: Thu Feb 10, 2005 11:00 pm
Location: Fife Scotland

Post Mon Feb 12, 2007 9:24 pm

:screwy:
gareth
E30 Zone Team Member
E30 Zone Team Member
Posts: 11005
Joined: Tue Jan 11, 2005 11:00 pm
Location: hastings, east sussex

Post Mon Feb 12, 2007 9:26 pm

worth a go i guess. i suspect the curing times for the rear could be drastically longer due to the very restricted airflow and visible area on the material you add. maybe pulling the caps off when you're done and the car is on the ground would help it a bit, just don't drive away!!!!

operation test-pilot commences here!
Sole founder of Fe2O3-12V it's a lifestyle
Image
LSD rebuilding / modification services provided, PM for details
bigdek
E30 Zone Camper
E30 Zone Camper
Posts: 1115
Joined: Thu Feb 10, 2005 11:00 pm
Location: Fife Scotland

Post Mon Feb 12, 2007 9:28 pm

just kidding m8.

guess u can only try it
DRIFTBOY
E30 Zone Addict
E30 Zone Addict
Posts: 3131
Joined: Mon May 22, 2006 11:00 pm
Location: Kent

Post Mon Feb 12, 2007 9:33 pm

I've not really finding any downsides to having poly bushes and I'm quite impressed with mine. I've not driven an E30 hard with good standard bushes though, is there really that much of a downside to poly ones?

I've heard a few people say they don't like them.

Just interested to hear your valued opinion really.

Thanks,

Martin.
Jeremy Clarkson wrote:...but it drives the front wheels. Theee wrooong wheels!
da4x4turbo wrote:I raced a vivaro on the motorway once in a 318is.... and lost!!!
Andy335Touring
Married to the E30 Zone
Married to the E30 Zone
Posts: 7144
Joined: Sun Jan 09, 2005 11:00 pm
Location: Long Eaton,Nottingham

Post Mon Feb 12, 2007 9:47 pm

gareth wrote:worth a go i guess. i suspect the curing times for the rear could be drastically longer due to the very restricted airflow and visible area on the material you add. maybe pulling the caps off when you're done and the car is on the ground would help it a bit, just don't drive away!!!!
Mmm, i wonder if the best way is to leave the caps off like you say, have it on axle stands with a jack on the subframe to make sure the bushes are roughly compressed as much as if the car was sitting on it's wheels ??
Andy335Touring
Married to the E30 Zone
Married to the E30 Zone
Posts: 7144
Joined: Sun Jan 09, 2005 11:00 pm
Location: Long Eaton,Nottingham

Post Mon Feb 12, 2007 9:52 pm

DRIFTBOY wrote:I've not really finding any downsides to having poly bushes and I'm quite impressed with mine. I've not driven an E30 hard with good standard bushes though, is there really that much of a downside to poly ones?

I've heard a few people say they don't like them.

Just interested to hear your valued opinion really.

Thanks,

Martin.
TBH I don't have any first hand experiance with poly bushes, i'm going on what i've read on here really.

Did you notice any extra noise or did the bumps seem more crashy/harsh when you changed over ?
Andy335Touring
Married to the E30 Zone
Married to the E30 Zone
Posts: 7144
Joined: Sun Jan 09, 2005 11:00 pm
Location: Long Eaton,Nottingham

Post Mon Feb 12, 2007 9:53 pm

bigdek wrote:just kidding m8.

guess u can only try it
LOL, cheers D :thumb:
gareth
E30 Zone Team Member
E30 Zone Team Member
Posts: 11005
Joined: Tue Jan 11, 2005 11:00 pm
Location: hastings, east sussex

Post Mon Feb 12, 2007 10:02 pm

Andy335Touring wrote:
gareth wrote:worth a go i guess. i suspect the curing times for the rear could be drastically longer due to the very restricted airflow and visible area on the material you add. maybe pulling the caps off when you're done and the car is on the ground would help it a bit, just don't drive away!!!!
Mmm, i wonder if the best way is to leave the caps off like you say, have it on axle stands with a jack on the subframe to make sure the bushes are roughly compressed as much as if the car was sitting on it's wheels ??
don't do that jack the car from the subframe, it'll trash your bushes! if you think about it, the weight of the car doesn't sit on the subframe at all... the rear of the car is suported on the springs which sit on the trailing arms. little load passes though the subframe.

why not jack up, pull off the caps, pump in the goo, refit the caps, drop onto the floor, drive about a bit to settle things, remove the caps... that'll replicate the loaded state best.
Sole founder of Fe2O3-12V it's a lifestyle
Image
LSD rebuilding / modification services provided, PM for details
Andy325i
E30 Zone Addict
E30 Zone Addict
Posts: 4052
Joined: Mon Jan 10, 2005 11:00 pm
Location: Avon

Post Mon Feb 12, 2007 10:04 pm

Andy335Touring wrote:


Did you notice any extra noise or did the bumps seem more crashy/harsh when you changed over ?
Just my 2P worth:

I fitted polly subframe bushes and didn't notice any more road noise etc, just slighty more responsive. On the subject of polly bushes on the rear of the front arms are well worth doing :) £ for £ they are the best mod I have ever done :D

Andy
Last edited by Andy325i on Mon Feb 12, 2007 10:07 pm, edited 1 time in total.
Image
M50B25NonVanos & M52B28Vanos Heads for sale. Pm Me.
Andy335Touring
Married to the E30 Zone
Married to the E30 Zone
Posts: 7144
Joined: Sun Jan 09, 2005 11:00 pm
Location: Long Eaton,Nottingham

Post Mon Feb 12, 2007 10:07 pm

gareth wrote:
don't do that jack the car from the subframe, it'll trash your bushes!
Bollox, i thought it was OK, this might be my problem :cry:
Andy335Touring
Married to the E30 Zone
Married to the E30 Zone
Posts: 7144
Joined: Sun Jan 09, 2005 11:00 pm
Location: Long Eaton,Nottingham

Post Mon Feb 12, 2007 10:10 pm

Andy325i wrote:
I fitted polly subframe bushes and didn't notice any more road noise etc, just slighty more responsive.

Andy
Cheers for your feed back mate :thumb:

How is your conversion going ?
oze30
E30 Zone Addict
E30 Zone Addict
Posts: 4133
Joined: Mon Oct 24, 2005 11:00 pm
Location: Sydney

Post Mon Feb 12, 2007 10:11 pm

There's a company in the states that makes stainless steel or metal bushes. They replace the rubber/poly ones with solid metal. They say its for race only..
Andy325i
E30 Zone Addict
E30 Zone Addict
Posts: 4052
Joined: Mon Jan 10, 2005 11:00 pm
Location: Avon

Post Mon Feb 12, 2007 10:13 pm

No worries :D

which one mate? The 2.8?

All good ta, but saving for a more sensible diff/rear end atm

Not sure if I am going to go E36/ E30 M3 for the 5 stud conversion yet :mad:

Andy
Image
M50B25NonVanos & M52B28Vanos Heads for sale. Pm Me.
Andy335Touring
Married to the E30 Zone
Married to the E30 Zone
Posts: 7144
Joined: Sun Jan 09, 2005 11:00 pm
Location: Long Eaton,Nottingham

Post Mon Feb 12, 2007 10:16 pm

oze30 wrote:There's a company in the states that makes stainless steel or metal bushes. They replace the rubber/poly ones with solid metal. They say its for race only..
Yeah, i've seen almost every E30 bush made in metal, like you say, track only really
Andy335Touring
Married to the E30 Zone
Married to the E30 Zone
Posts: 7144
Joined: Sun Jan 09, 2005 11:00 pm
Location: Long Eaton,Nottingham

Post Mon Feb 12, 2007 10:19 pm

Andy325i wrote:No worries :D

which one mate? The 2.8?

All good ta, but saving for a more sensible diff/rear end atm

Not sure if I am going to go E36/ E30 M3 for the 5 stud conversion yet :mad:

Andy
Cool, glad it's(2.8 ) going well, whats the other project ?

I'd love to go 5 stud but it's not cheap is it with wheels/tyres/etc :(
Andy325i
E30 Zone Addict
E30 Zone Addict
Posts: 4052
Joined: Mon Jan 10, 2005 11:00 pm
Location: Avon

Post Mon Feb 12, 2007 10:25 pm

Andy335Touring wrote:
whats the other project ?


I'd love to go 5 stud but it's not cheap is it with wheels/tyres/etc :(
I can't possibly say yet (only in the planning atm) but all will be revealed I promise :D

Yep know what you mean about the 5 stud being expensive, but imho it offers a far better range of wheels etc weather it be E30 M3 or E36 route :D

Andy
Image
M50B25NonVanos & M52B28Vanos Heads for sale. Pm Me.
Andy335Touring
Married to the E30 Zone
Married to the E30 Zone
Posts: 7144
Joined: Sun Jan 09, 2005 11:00 pm
Location: Long Eaton,Nottingham

Post Mon Feb 12, 2007 10:28 pm

yer big tease :)

<edit> LOL, how :gay: does that sound ! :eek: :)
gareth
E30 Zone Team Member
E30 Zone Team Member
Posts: 11005
Joined: Tue Jan 11, 2005 11:00 pm
Location: hastings, east sussex

Post Mon Feb 12, 2007 10:52 pm

Andy335Touring wrote:
gareth wrote:
don't do that jack the car from the subframe, it'll trash your bushes!
Bollox, i thought it was OK, this might be my problem :cry:
most E30's have had this done over the years. as the bottom of the diff looks so tempting and it's a pain to do otherwise.

if you look at the subframe bushes while you jack from the subframe you'll see them getting stretched to hell! there wa a big argument on here a while ago with people saying that i must be wrong as it's ok on a subaru etc etc etc but not on a E30 as the weight is simply not designed to pass though there and the diff bush.

oh well, at least they're cheap... just a pig to swap!
Sole founder of Fe2O3-12V it's a lifestyle
Image
LSD rebuilding / modification services provided, PM for details
DRIFTBOY
E30 Zone Addict
E30 Zone Addict
Posts: 3131
Joined: Mon May 22, 2006 11:00 pm
Location: Kent

Post Tue Feb 13, 2007 12:08 am

Andy335Touring wrote:
DRIFTBOY wrote:I've not really finding any downsides to having poly bushes and I'm quite impressed with mine. I've not driven an E30 hard with good standard bushes though, is there really that much of a downside to poly ones?

I've heard a few people say they don't like them.

Just interested to hear your valued opinion really.

Thanks,

Martin.
TBH I don't have any first hand experiance with poly bushes, i'm going on what i've read on here really.

Did you notice any extra noise or did the bumps seem more crashy/harsh when you changed over ?
I didn't notice them being harsh or noisy in any way, even with no soundproofing at all (just carpet), as Andy325i said, I only noticed a positive result. And they are really easy to fit - once the old bushes are out!
Jeremy Clarkson wrote:...but it drives the front wheels. Theee wrooong wheels!
da4x4turbo wrote:I raced a vivaro on the motorway once in a 318is.... and lost!!!
Andy335Touring
Married to the E30 Zone
Married to the E30 Zone
Posts: 7144
Joined: Sun Jan 09, 2005 11:00 pm
Location: Long Eaton,Nottingham

Post Tue Feb 13, 2007 7:22 pm

Cheers for the help/info chaps :cool:

Not sure now, i might just pack them out with this Window seal stuff and see how i get on(easy and cheap), if thats no good then i'll use some proper polly bushes(ball ache and more £Â£Ã‚£).
DRIFTBOY
E30 Zone Addict
E30 Zone Addict
Posts: 3131
Joined: Mon May 22, 2006 11:00 pm
Location: Kent

Post Tue Feb 13, 2007 8:04 pm

Andy335Touring wrote:Cheers for the help/info chaps :cool:

Not sure now, i might just pack them out with this Window seal stuff and see how i get on(easy and cheap), if thats no good then i'll use some proper polly bushes(ball ache and more £Â£Ã‚£).
Sounds like a good plan!

But please let us all know if it works or not - you could be on to something! :D
Jeremy Clarkson wrote:...but it drives the front wheels. Theee wrooong wheels!
da4x4turbo wrote:I raced a vivaro on the motorway once in a 318is.... and lost!!!