Stud extractor needed?

Need technical Q/A then you're in the right place

Moderator: martauto

eko
Old timer
Posts: 11531
Joined: Sat Feb 05, 2005 11:00 pm
Location: South Devon

Post Fri Feb 02, 2007 10:27 pm

I need advice on stud extractor to use to remove snapped bolt that is flush.
Please refer to this thread for details -
http://www.e30zone.net/modules.php?name ... ic&t=56765
Image
eko
Old timer
Posts: 11531
Joined: Sat Feb 05, 2005 11:00 pm
Location: South Devon

Post Sat Feb 03, 2007 12:32 am

Anyone?
Image
Templ8e30
E30 Zone Addict
E30 Zone Addict
Posts: 2801
Joined: Mon Jan 10, 2005 11:00 pm
Location: Ashton-under-Lyne, Lancashire

Post Sat Feb 03, 2007 8:48 pm

Not a hop in hell of getting that out without removing the diff IMO

It'll need drilling dead centre and an easy-out or something similar to extract it.

Cheers,

Iain T
Image
2007 Mazda 6 2.0 estate
Political Correctness - A concept based on the idea that its possible to pick up a turd by the clean end !
eko
Old timer
Posts: 11531
Joined: Sat Feb 05, 2005 11:00 pm
Location: South Devon

Post Sat Feb 03, 2007 8:52 pm

Templ8e30 wrote:Not a hop in hell of getting that out without removing the diff IMO

It'll need drilling dead centre and an easy-out or something similar to extract it.

Cheers,

Iain T
Exactly my thinking too :?

Was thinking about how ill go about it before,do you think some heat on it will loosen it?
Or is this likely to make the job worse?

Maybe hacksaw a slot into the end,obviously itll cut into the housing a bit to,then warm it up and try and impact screwdri9ver it out?
Image
Andy335Touring
Married to the E30 Zone
Married to the E30 Zone
Posts: 7144
Joined: Sun Jan 09, 2005 11:00 pm
Location: Long Eaton,Nottingham

Post Sat Feb 03, 2007 9:37 pm

Can you get to weld an old bolt or some thing on it ?
eko
Old timer
Posts: 11531
Joined: Sat Feb 05, 2005 11:00 pm
Location: South Devon

Post Sat Feb 03, 2007 9:42 pm

Andy335Touring wrote:Can you get to weld an old bolt or some thing on it ?
Not sure to be honest?
Be a damn site easier if i could get it on a ramp though :mad:

Going to get it up on ramps tomorrow and have a closer look,bit of head scratching,then probably get the tools out and starting taking the b4stard out :mad:
Image
fuzzy
He who sleeps with "Gingers"
Posts: 14351
Joined: Sat Jun 04, 2005 11:00 pm
Location: melbourne Australia

Post Sat Feb 03, 2007 10:06 pm

cant see you being able to weld on to it tbh. wouldnt be to difficult to remove with a stud extractor but will need the diff removed which isnt a difficult job either.id reckon half a day to finish it.
e21Jason
E30 Zone Addict
E30 Zone Addict
Posts: 2040
Joined: Tue Jan 11, 2005 11:00 pm
Location: Dubai, UAE

Post Sat Feb 03, 2007 10:56 pm

Hi

Try some Irwin bolt extractors

http://www.irwin.com/irwin/consumer/jht ... nCat100511

Bought a set as I had a hexbolt round of one the inside, used loads since i show my nuts no mercy

Jason
M3Compact
E30 Zone Regular
E30 Zone Regular
Posts: 506
Joined: Mon Jan 10, 2005 11:00 pm

Post Sat Feb 03, 2007 11:07 pm

Templ8e30 wrote:Not a hop in hell of getting that out without removing the diff IMO

It'll need drilling dead centre and an easy-out or something similar to extract it.

Cheers,

Iain T
Agreed unfortunately. :(

Taking the diff out's a pita. :roll:

But...Wasting hours and getting pi55ed off, then taking the diff out is a bigger pita. :(
Templ8e30
E30 Zone Addict
E30 Zone Addict
Posts: 2801
Joined: Mon Jan 10, 2005 11:00 pm
Location: Ashton-under-Lyne, Lancashire

Post Sun Feb 04, 2007 5:43 pm

These would work better in this case http://www.irwin.com/irwin/consumer/jht ... Prod100510

Cheers,

Iain T
Image
2007 Mazda 6 2.0 estate
Political Correctness - A concept based on the idea that its possible to pick up a turd by the clean end !
bennyboy
E30 Zone Newbie
E30 Zone Newbie
Posts: 218
Joined: Mon Jan 10, 2005 11:00 pm
Location: West Sussex

Post Sun Feb 04, 2007 7:42 pm

Halfords do a set of Lazer stud extractors for about £6-7. i used these to get my wheel nuts off when i lost the key. Just drill into the centre of the stud/bolt and wind one of them into your drill hole. They are a reverse thread so when they go tight they start undoing the bolt. Good luck dude!
Image
16V IS engine!!!