I need advice on stud extractor to use to remove snapped bolt that is flush.
Please refer to this thread for details -
http://www.e30zone.net/modules.php?name ... ic&t=56765
Stud extractor needed?
Moderator: martauto
-
Templ8e30
- E30 Zone Addict

- Posts: 2801
- Joined: Mon Jan 10, 2005 11:00 pm
- Location: Ashton-under-Lyne, Lancashire
Not a hop in hell of getting that out without removing the diff IMO
It'll need drilling dead centre and an easy-out or something similar to extract it.
Cheers,
Iain T
It'll need drilling dead centre and an easy-out or something similar to extract it.
Cheers,
Iain T

2007 Mazda 6 2.0 estate
Political Correctness - A concept based on the idea that its possible to pick up a turd by the clean end !
-
eko
- Old timer
- Posts: 11531
- Joined: Sat Feb 05, 2005 11:00 pm
- Location: South Devon
Exactly my thinking tooTempl8e30 wrote:Not a hop in hell of getting that out without removing the diff IMO
It'll need drilling dead centre and an easy-out or something similar to extract it.
Cheers,
Iain T
Was thinking about how ill go about it before,do you think some heat on it will loosen it?
Or is this likely to make the job worse?
Maybe hacksaw a slot into the end,obviously itll cut into the housing a bit to,then warm it up and try and impact screwdri9ver it out?

-
Andy335Touring
- Married to the E30 Zone

- Posts: 7144
- Joined: Sun Jan 09, 2005 11:00 pm
- Location: Long Eaton,Nottingham
Can you get to weld an old bolt or some thing on it ?
-
eko
- Old timer
- Posts: 11531
- Joined: Sat Feb 05, 2005 11:00 pm
- Location: South Devon
Not sure to be honest?Andy335Touring wrote:Can you get to weld an old bolt or some thing on it ?
Be a damn site easier if i could get it on a ramp though
Going to get it up on ramps tomorrow and have a closer look,bit of head scratching,then probably get the tools out and starting taking the b4stard out

-
fuzzy
- He who sleeps with "Gingers"
- Posts: 14351
- Joined: Sat Jun 04, 2005 11:00 pm
- Location: melbourne Australia
cant see you being able to weld on to it tbh. wouldnt be to difficult to remove with a stud extractor but will need the diff removed which isnt a difficult job either.id reckon half a day to finish it.
-
e21Jason
- E30 Zone Addict

- Posts: 2040
- Joined: Tue Jan 11, 2005 11:00 pm
- Location: Dubai, UAE
Hi
Try some Irwin bolt extractors
http://www.irwin.com/irwin/consumer/jht ... nCat100511
Bought a set as I had a hexbolt round of one the inside, used loads since i show my nuts no mercy
Jason
Try some Irwin bolt extractors
http://www.irwin.com/irwin/consumer/jht ... nCat100511
Bought a set as I had a hexbolt round of one the inside, used loads since i show my nuts no mercy
Jason
-
M3Compact
- E30 Zone Regular

- Posts: 506
- Joined: Mon Jan 10, 2005 11:00 pm
Agreed unfortunately.Templ8e30 wrote:Not a hop in hell of getting that out without removing the diff IMO
It'll need drilling dead centre and an easy-out or something similar to extract it.
Cheers,
Iain T
Taking the diff out's a pita.
But...Wasting hours and getting pi55ed off, then taking the diff out is a bigger pita.
-
Templ8e30
- E30 Zone Addict

- Posts: 2801
- Joined: Mon Jan 10, 2005 11:00 pm
- Location: Ashton-under-Lyne, Lancashire
These would work better in this case http://www.irwin.com/irwin/consumer/jht ... Prod100510
Cheers,
Iain T
Cheers,
Iain T

2007 Mazda 6 2.0 estate
Political Correctness - A concept based on the idea that its possible to pick up a turd by the clean end !
-
bennyboy
- E30 Zone Newbie

- Posts: 218
- Joined: Mon Jan 10, 2005 11:00 pm
- Location: West Sussex
Halfords do a set of Lazer stud extractors for about £6-7. i used these to get my wheel nuts off when i lost the key. Just drill into the centre of the stud/bolt and wind one of them into your drill hole. They are a reverse thread so when they go tight they start undoing the bolt. Good luck dude!

16V IS engine!!!
