How to i get round a naffed wheel nut???

Need technical Q/A then you're in the right place

Moderator: martauto

ag-1982
E30 Zone Newbie
E30 Zone Newbie
Posts: 114
Joined: Thu Jan 04, 2007 11:00 pm
Location: SE Kent

Post Thu Feb 01, 2007 5:48 pm

I was fitting my alloy wheels the other day and as i came to the final nut on the last wheel i found out it had been completely rounded off :x

Anyone out there with any ideas as to how i can get the bitch off

cheers
DanThe
E30 Zone Team Member
E30 Zone Team Member
Posts: 28649
Joined: Sat Sep 10, 2005 11:00 pm
Location: Staffs

Post Thu Feb 01, 2007 5:50 pm

Drill the centre until the head falls of. Once youve taken the wheel off the remaining peice will unscrew by hand/molegrips
maxfield
Old Skooler
Old Skooler
Posts: 15185
Joined: Sat Nov 26, 2005 11:00 pm
Location: Mansfield

Post Thu Feb 01, 2007 5:51 pm

you got acces to a welder ??

welder another bolt onto it ??

or maybe get a dremel and cut throught the middle and use some sort of screw driver

or drill a hole into the top and get something in there and hammer it round

probably easyer ways but only ones i can think of
Image
noney82
E30 Zone Camper
E30 Zone Camper
Posts: 1102
Joined: Thu Apr 27, 2006 11:00 pm
Location: manchester, stockport

Post Thu Feb 01, 2007 5:53 pm

i had this problem once it was a 17mm rouunded off, i got a 16mm socket and hit it on the nut with hammer then got a big breaker bar and slowly went for it, worked a treat but couldnt use 16mm again but was worth it.
ag-1982
E30 Zone Newbie
E30 Zone Newbie
Posts: 114
Joined: Thu Jan 04, 2007 11:00 pm
Location: SE Kent

Post Thu Feb 01, 2007 5:55 pm

cheers guys ill try these in the morning :wink:
car looks shite with only 3 alloys on it :o:
mrLEE30
E30 Zone Team Member
E30 Zone Team Member
Posts: 6589
Joined: Tue Jan 18, 2005 11:00 pm
Location: Sweating buckets in Bahrain

Post Thu Feb 01, 2007 5:56 pm

maxfield technique is quickest if you have the tools,

dans works with tools at home, but take your time and start with small (4-5mm tungsten carbide high speed drill bits) and make sure you are in the middle (use a punch to start the first hole) then use progessively bigger drill bits till the nut falls off. you will also need a decent drill.
Image
Speedtouch
Old Skooler
Old Skooler
Posts: 14130
Joined: Tue Feb 14, 2006 11:00 pm
Location: Canterbury

Post Thu Feb 01, 2007 5:58 pm

You can buy 'Easy out' stud removers with reverse thread, so you drill a hole in the stud, tap it with the reverse thread, screw in the removal too and undo as normal:


http://search.ebay.com/easy-out_W0QQfnuZ1
http://buy1.snapon.com/catalog/tools.as ... apon-store

HTH,
///M aurice
ECU Upgrade EPROM Chips, £40 posted within the UK. Note these are not Zone chips.
viewtopic.php?f=6&t=279421
appletree
E30 Zone Addict
E30 Zone Addict
Posts: 3479
Joined: Fri Jan 20, 2006 11:00 pm
Location: Retford

Post Thu Feb 01, 2007 6:03 pm

depending on how rounded off it is an imperial socket might just knock on and do it, also what type of socket do you have some work of the corners (like a ring spanner) and some work of the flats if youve got the flat type it might just work anyway:D
Image

You should never underestimate the predictability of stupidity

M42 Supercharged 285bhp + M3 6speed box
Chris-W
E30 Zone Team Member
E30 Zone Team Member
Posts: 7219
Joined: Tue May 24, 2005 11:00 pm
Location: South Cheshire

Post Thu Feb 01, 2007 6:03 pm

17mm bolt extractor - I have a set made by Irwin which are fine.
Image
feens
E30 Zone Regular
E30 Zone Regular
Posts: 460
Joined: Fri May 19, 2006 11:00 pm
Location: Longford

Post Thu Feb 01, 2007 8:39 pm

Had the same problem christmas day of all days, got a puncture and Rounded the bolt
took me 2 days with dimand tipped drill bits to drill the head off the bolt! and Tried all of the above before hand Welded a nut onto the stud and it snapped off bringing half the bolt head with it! was a bloody nightmare! Got it out eventually after i threw a few Fcuk's into it Without Damaging the alloy luckily enough!
SPADGE
Married to the E30 Zone
Married to the E30 Zone
Posts: 7373
Joined: Wed Aug 09, 2006 11:00 pm
Location: Milton Keynes, Bucks

Post Thu Feb 01, 2007 9:11 pm

noney82 wrote:i had this problem once it was a 17mm rouunded off, i got a 16mm socket and hit it on the nut with hammer then got a big breaker bar and slowly went for it, worked a treat but couldnt use 16mm again but was worth it.
That way has worked every time for me especialy with fecked locking wheel nuts!
Engine conversions, Auto to manual conversions, parts, servicing etc etc... For anything e30 call 07718 901737
DanThe
E30 Zone Team Member
E30 Zone Team Member
Posts: 28649
Joined: Sat Sep 10, 2005 11:00 pm
Location: Staffs

Post Thu Feb 01, 2007 9:24 pm

How do you boys manage to 'round off' wheel bolts?

You must be using some really cheap sh!t pound shop sockets! The only type of socket you should be using is a deep hexagon, the depth to keep the bar away from the wheel rim and the hexagon to hold the bolt properly.

I wouldnt put a welder near my rims, alloy doesnt take to kindly to molten steel.

Diamond tipped? Wilco special by any chance? :) Carbide is the best for the job, but standard HSS bits (of half decent quality) will do if sharpened properly.
handpaper
E30 Zone Regular
E30 Zone Regular
Posts: 883
Joined: Sun Apr 16, 2006 11:00 pm
Location: Newport, South Wales

Post Thu Feb 01, 2007 11:23 pm

How do you boys manage to 'round off' wheel bolts?

You must be using some really cheap sh!t pound shop sockets! The only type of socket you should be using is a deep hexagon, the depth to keep the bar away from the wheel rim and the hexagon to hold the bolt properly.
Personally, I like the OEM wheelbrace; a high quality bit of kit, which - surprise surprise - fits the bolts perfectly :)
feens
E30 Zone Regular
E30 Zone Regular
Posts: 460
Joined: Fri May 19, 2006 11:00 pm
Location: Longford

Post Thu Feb 01, 2007 11:25 pm

DanThe wrote:How do you boys manage to 'round off' wheel bolts?

You must be using some really cheap sh!t pound shop sockets! The only type of socket you should be using is a deep hexagon, the depth to keep the bar away from the wheel rim and the hexagon to hold the bolt properly.

I wouldnt put a welder near my rims, alloy doesnt take to kindly to molten steel.

Diamond tipped? Wilco special by any chance? :) Carbide is the best for the job, but standard HSS bits (of half decent quality) will do if sharpened properly.
Their the ones dude ate thru the stud with ease! must have went thru 20 odd HSS bits first all New one's mind! Than god my mate had the key's to a machining shop that day! otherwise i think id still be there Lol :)
ag-1982
E30 Zone Newbie
E30 Zone Newbie
Posts: 114
Joined: Thu Jan 04, 2007 11:00 pm
Location: SE Kent

Post Fri Feb 02, 2007 12:20 pm

I didnt round the bolt off myself looks like some arse has tried to get past a locking wheel nut without using the key and totally naffed it :-x
spence_star
E30 Zone Regular
E30 Zone Regular
Posts: 512
Joined: Thu Nov 23, 2006 11:00 pm
Location: London

Post Fri Feb 02, 2007 1:08 pm

Mate, contact this geeza and tell him Spencer gave you his number.

Dukes Tyres = 07956 015523

He did mu dud nuts.
Returned after many years out.
cliffybabe
Powered by Nelly
Powered by Nelly
Posts: 10020
Joined: Sun Dec 18, 2005 11:00 pm
Location: Croydon

Post Fri Feb 02, 2007 1:13 pm

ring the AA and ge tthem to sort it winkeye
Image
Considering Selling the Cabby, looks like its gonna go
appletree
E30 Zone Addict
E30 Zone Addict
Posts: 3479
Joined: Fri Jan 20, 2006 11:00 pm
Location: Retford

Post Sat Feb 03, 2007 5:38 pm

For drilling hard materials a cheap solution is to use an ordinary masonary drill, best if you can grind the tip to a profile like a HSS drill on a green grinding wheel. I found this out when my dad broke not 1 but 2 HSS centre drills helping me drill my stainless manifold :eek: . However he did help me get them out. :roll:
Image

You should never underestimate the predictability of stupidity

M42 Supercharged 285bhp + M3 6speed box
ag-1982
E30 Zone Newbie
E30 Zone Newbie
Posts: 114
Joined: Thu Jan 04, 2007 11:00 pm
Location: SE Kent

Post Sat Feb 03, 2007 7:00 pm

Cheers guys came off real easy, thanks for all your help
top job :D