differences in cylinder heads?

Need technical Q/A then you're in the right place

Moderator: martauto

Giggz
E30 Zone Camper
E30 Zone Camper
Posts: 1270
Joined: Wed Apr 13, 2005 11:00 pm
Location: East London

Post Sun Jan 28, 2007 7:39 pm

Is there any difference in cylinder heads pre 1988?

Im after one and have just been offered a cylinder head from a d plate auto. My car is 1988. 325i.

Can this be used?

Thanks?
Image
^stolen but not forgotten^
StuBeeDoo
Engaged to the E30 Zone
Engaged to the E30 Zone
Posts: 6756
Joined: Sat Feb 05, 2005 11:00 pm
Location: Up My Own Arse

Post Sun Jan 28, 2007 7:45 pm

AFAIK, 'heads are the same. Difference in compression ratio was from different pistons.
This is why I no longer drive an E30......

Image
Giggz
E30 Zone Camper
E30 Zone Camper
Posts: 1270
Joined: Wed Apr 13, 2005 11:00 pm
Location: East London

Post Sun Jan 28, 2007 7:56 pm

Fair enough. Thanks for the info.
Image
^stolen but not forgotten^
Turbo-Brown
Boost Junkie
Posts: 4705
Joined: Tue Feb 15, 2005 11:00 pm
Location: Aldershot, Hants

Post Sun Jan 28, 2007 9:15 pm

That's handy to know, I was gonna ask the same question at some point :D
325i Twin Turbo (until 10am 01/12/07 :( )

www.air-in.co.uk free M20 exhaust and inlet flange
Giggz
E30 Zone Camper
E30 Zone Camper
Posts: 1270
Joined: Wed Apr 13, 2005 11:00 pm
Location: East London

Post Sun Jan 28, 2007 9:32 pm

Another question i have now is when a engine has been 'rebuilt' what sort of work would of the head had. Is it a case of just cleaning it up?
Image
^stolen but not forgotten^
StuBeeDoo
Engaged to the E30 Zone
Engaged to the E30 Zone
Posts: 6756
Joined: Sat Feb 05, 2005 11:00 pm
Location: Up My Own Arse

Post Sun Jan 28, 2007 9:57 pm

Giggz wrote:Another question i have now is when a engine has been 'rebuilt' what sort of work would of the head had. Is it a case of just cleaning it up?
Could be everything, could be nothing much.
Same goes for the bottom end.
A proper rebuild should be anything showing the slightest bit of wear replaced.
Someone on a tight budget would probably just replace anything that's totally shagged (possibly with second-hand!) and kid themselves that they've done it properly.
A properly rebuilt head should be pressure tested, re-faced, have all new manifold studs fitted, possibly new valve seats, new valves, valve guides, valve stem seals, valve springs, rockers and shafts, camshaft, oil spray bar and camshaft oil seal and housing o-ring.
This is why I no longer drive an E30......

Image
Giggz
E30 Zone Camper
E30 Zone Camper
Posts: 1270
Joined: Wed Apr 13, 2005 11:00 pm
Location: East London

Post Sun Jan 28, 2007 10:17 pm

If the head i have been offered has had all that done to it then i shall be very happy!

Thats some very handy info there sir. Thanks.

What else do you reckon i can do to the engine to give it a new lease of life whilst the head is off.

I dont want to do any mods. Just want to renew or replace.
Image
^stolen but not forgotten^
kam-325i
E30 Zone Team Member
E30 Zone Team Member
Posts: 4851
Joined: Tue Sep 27, 2005 11:00 pm
Location: TELFORD !!!! (Shropshire) Stevetigger Land !!!

Post Sun Jan 28, 2007 10:18 pm

Clean , Clean & Clean........
Pete don't care about colour, He would shag a rainbow if he could find the end of it....
Image
Giggz
E30 Zone Camper
E30 Zone Camper
Posts: 1270
Joined: Wed Apr 13, 2005 11:00 pm
Location: East London

Post Sun Jan 28, 2007 10:22 pm

Oh hell yeah! :lol:

Goes without saying.

Any special products i should look out for?
Image
^stolen but not forgotten^
kam-325i
E30 Zone Team Member
E30 Zone Team Member
Posts: 4851
Joined: Tue Sep 27, 2005 11:00 pm
Location: TELFORD !!!! (Shropshire) Stevetigger Land !!!

Post Sun Jan 28, 2007 10:25 pm

I just used alot of white spirits.....
Pete don't care about colour, He would shag a rainbow if he could find the end of it....
Image