M42 chain tensioner fitting question

Need technical Q/A then you're in the right place

Moderator: martauto

User avatar
kevin316i
E30 Zone Regular
E30 Zone Regular
Posts: 783
Joined: Mon Jan 10, 2005 11:00 pm

Post Mon Jan 22, 2007 2:13 pm

I was reading up on the procedure for fitting a new timing chain tensioner to the M42 engine and it stated you start the car and rev the engine at about 3000rpm to get the new tensioner to unlock and take up tension.

My question is:
Is there any risk at running the engine at these revs with a slack chain, before the tensioner takes up the slack? Any chance the chain might dislocate itself off one of the cogs?

Sorry of this seems like a stupid question, but I'd like to be straight in my head about this before doing the job.

(my boss at work tells me I over-analyse things, where did he get that idea from???)
Chris-W
E30 Zone Team Member
E30 Zone Team Member
Posts: 7219
Joined: Tue May 24, 2005 11:00 pm
Location: South Cheshire

Post Mon Jan 22, 2007 6:46 pm

That's standard procedure to get the oil pressure up to extend the tensioner.
Image
User avatar
kevin316i
E30 Zone Regular
E30 Zone Regular
Posts: 783
Joined: Mon Jan 10, 2005 11:00 pm

Post Tue Jan 23, 2007 9:19 am

Thanks Chris,

Just wondering if there was any risk to the chain before the new tensioner takes up the slack.
Chris-W
E30 Zone Team Member
E30 Zone Team Member
Posts: 7219
Joined: Tue May 24, 2005 11:00 pm
Location: South Cheshire

Post Tue Jan 23, 2007 9:35 am

Never had a problem and the chain isn't exactly 'loose' without the tensioner.
Image
User avatar
kevin316i
E30 Zone Regular
E30 Zone Regular
Posts: 783
Joined: Mon Jan 10, 2005 11:00 pm

Post Tue Jan 23, 2007 11:18 am

Thanks Chris,

Think I need to stop 'over-analysing' :D

Regards,
Kevin
Chris-W
E30 Zone Team Member
E30 Zone Team Member
Posts: 7219
Joined: Tue May 24, 2005 11:00 pm
Location: South Cheshire

Post Tue Jan 23, 2007 11:20 am

kevin316i wrote:Think I need to stop 'over-analysing' :D
But are you absolutely sure? Best give it some thought. :D
Image
320Touring
E30 Zone Team Member
E30 Zone Team Member
Posts: 12316
Joined: Fri Feb 11, 2005 11:00 pm
Location: Glasgow (Scotland)

Post Tue Jan 23, 2007 11:20 am

Start her up once its fitted. they make so much noise that for the next two weeks you'll not notice the normal iS rattle :D

remember and get the m44 (e36) tensioner as its a reccomended upgrade over the m42 part
The big Unit Parts Clear out Make me an offer on parts!
http://www.e30zone.net/modules.php?name ... 81#2766881
User avatar
kevin316i
E30 Zone Regular
E30 Zone Regular
Posts: 783
Joined: Mon Jan 10, 2005 11:00 pm

Post Wed Jan 24, 2007 9:55 am

Chain isn't really rattling, but the only evidence I can find of tensionser replacement is in a receipt that goes back to 1995, so recon it's time for a new one.
Demlotcrew
E30 Zone Team Member
E30 Zone Team Member
Posts: 13329
Joined: Mon Dec 20, 2004 11:00 pm
Location: East Anglia

Post Wed Jan 24, 2007 12:20 pm

BMW tech manuals tell a different story, the tensioner must not be installed in the 'delivery' state with the intention of unlocking it by running the engine.

The best way is to knock the tensioner to unlock it (do it in the packet just in case it breaks apart) then install it in its fully open state, its quite easy to compress it as the spring is quite soft.

If the guides are worn there is every chance the chain can skip.

Andrew
User avatar
kevin316i
E30 Zone Regular
E30 Zone Regular
Posts: 783
Joined: Mon Jan 10, 2005 11:00 pm

Post Wed Jan 24, 2007 9:17 pm

I'd prefer that method Demlotcrew, but thought it wasn't possible to insert the new tensioner if it was unlocked.
Demlotcrew
E30 Zone Team Member
E30 Zone Team Member
Posts: 13329
Joined: Mon Dec 20, 2004 11:00 pm
Location: East Anglia

Post Wed Jan 24, 2007 9:37 pm

Its very possible, i have done it any of times on engine rebuilds

Andrew
boybimmerm3
E30 Zone Regular
E30 Zone Regular
Posts: 391
Joined: Sun Jan 09, 2005 11:00 pm
Location: Berkshire

Post Wed Jan 24, 2007 9:39 pm

What you are supposed to do is install it in the closed position as the new one comes, then with the cam cover off use a thin screwdriver or smoething similar to press the tensioner closed a bit further then the tensioner will release and contact the chain tensioner correctly. Then start the car and hold the revs for around 3000rpm for 30 secs.
stuartgallafant
E30 Zone Addict
E30 Zone Addict
Posts: 4531
Joined: Tue Mar 29, 2005 11:00 pm
Location: Costa del Croydon

Post Thu Jan 25, 2007 7:24 pm

boybimmerm3 wrote:What you are supposed to do is install it in the closed position as the new one comes, then with the cam cover off use a thin screwdriver or smoething similar to press the tensioner closed a bit further then the tensioner will release and contact the chain tensioner correctly. Then start the car and hold the revs for around 3000rpm for 30 secs.
yep, thats the way i did mine!!

i've also done it the other way and it worked fine
Image