I was reading up on the procedure for fitting a new timing chain tensioner to the M42 engine and it stated you start the car and rev the engine at about 3000rpm to get the new tensioner to unlock and take up tension.
My question is:
Is there any risk at running the engine at these revs with a slack chain, before the tensioner takes up the slack? Any chance the chain might dislocate itself off one of the cogs?
Sorry of this seems like a stupid question, but I'd like to be straight in my head about this before doing the job.
(my boss at work tells me I over-analyse things, where did he get that idea from???)
M42 chain tensioner fitting question
Moderator: martauto
-
Chris-W
- E30 Zone Team Member

- Posts: 7219
- Joined: Tue May 24, 2005 11:00 pm
- Location: South Cheshire
-
kevin316i
- E30 Zone Regular

- Posts: 783
- Joined: Mon Jan 10, 2005 11:00 pm
Thanks Chris,
Just wondering if there was any risk to the chain before the new tensioner takes up the slack.
Just wondering if there was any risk to the chain before the new tensioner takes up the slack.
-
Chris-W
- E30 Zone Team Member

- Posts: 7219
- Joined: Tue May 24, 2005 11:00 pm
- Location: South Cheshire
-
kevin316i
- E30 Zone Regular

- Posts: 783
- Joined: Mon Jan 10, 2005 11:00 pm
Thanks Chris,
Think I need to stop 'over-analysing'
Regards,
Kevin
Think I need to stop 'over-analysing'
Regards,
Kevin
-
Chris-W
- E30 Zone Team Member

- Posts: 7219
- Joined: Tue May 24, 2005 11:00 pm
- Location: South Cheshire
-
320Touring
- E30 Zone Team Member

- Posts: 12316
- Joined: Fri Feb 11, 2005 11:00 pm
- Location: Glasgow (Scotland)
Start her up once its fitted. they make so much noise that for the next two weeks you'll not notice the normal iS rattle
remember and get the m44 (e36) tensioner as its a reccomended upgrade over the m42 part
remember and get the m44 (e36) tensioner as its a reccomended upgrade over the m42 part
The big Unit Parts Clear out Make me an offer on parts!
http://www.e30zone.net/modules.php?name ... 81#2766881
http://www.e30zone.net/modules.php?name ... 81#2766881
-
kevin316i
- E30 Zone Regular

- Posts: 783
- Joined: Mon Jan 10, 2005 11:00 pm
Chain isn't really rattling, but the only evidence I can find of tensionser replacement is in a receipt that goes back to 1995, so recon it's time for a new one.
-
Demlotcrew
- E30 Zone Team Member

- Posts: 13329
- Joined: Mon Dec 20, 2004 11:00 pm
- Location: East Anglia
BMW tech manuals tell a different story, the tensioner must not be installed in the 'delivery' state with the intention of unlocking it by running the engine.
The best way is to knock the tensioner to unlock it (do it in the packet just in case it breaks apart) then install it in its fully open state, its quite easy to compress it as the spring is quite soft.
If the guides are worn there is every chance the chain can skip.
Andrew
The best way is to knock the tensioner to unlock it (do it in the packet just in case it breaks apart) then install it in its fully open state, its quite easy to compress it as the spring is quite soft.
If the guides are worn there is every chance the chain can skip.
Andrew
-
kevin316i
- E30 Zone Regular

- Posts: 783
- Joined: Mon Jan 10, 2005 11:00 pm
I'd prefer that method Demlotcrew, but thought it wasn't possible to insert the new tensioner if it was unlocked.
-
Demlotcrew
- E30 Zone Team Member

- Posts: 13329
- Joined: Mon Dec 20, 2004 11:00 pm
- Location: East Anglia
Its very possible, i have done it any of times on engine rebuilds
Andrew
Andrew
-
boybimmerm3
- E30 Zone Regular

- Posts: 391
- Joined: Sun Jan 09, 2005 11:00 pm
- Location: Berkshire
What you are supposed to do is install it in the closed position as the new one comes, then with the cam cover off use a thin screwdriver or smoething similar to press the tensioner closed a bit further then the tensioner will release and contact the chain tensioner correctly. Then start the car and hold the revs for around 3000rpm for 30 secs.
-
stuartgallafant
- E30 Zone Addict

- Posts: 4531
- Joined: Tue Mar 29, 2005 11:00 pm
- Location: Costa del Croydon
yep, thats the way i did mine!!boybimmerm3 wrote:What you are supposed to do is install it in the closed position as the new one comes, then with the cam cover off use a thin screwdriver or smoething similar to press the tensioner closed a bit further then the tensioner will release and contact the chain tensioner correctly. Then start the car and hold the revs for around 3000rpm for 30 secs.
i've also done it the other way and it worked fine



