E30 Auto To Manual....

Need technical Q/A then you're in the right place

Moderator: martauto

Stifla
E30 Zone Regular
E30 Zone Regular
Posts: 324
Joined: Sun Jun 26, 2005 11:00 pm
Location: The best part of the UK...The South!

Post Sat Jan 20, 2007 1:15 am

Hi all,

Has anyone had any experience of changing an E30 from auto to manual and what was involved, ive been trying to find a decent 2-door six-cylinder e30 for a few weeks now and a lot of the nicer ones tend to be auto's which is such a shame as some have been quite nice!

Obviously the box and flywheel would need to be changed but my concern is with the pedal assembly.
Can the manual pedals just bolt up as normal after removing the auto ones, or is the bulkhead completly different?
Iv got a feeling it might be...

I assume the transmission tunnels are the same size though?

Any helps appreciated cheers! :D
mac325i
E30 Zone Newbie
E30 Zone Newbie
Posts: 116
Joined: Thu Jul 28, 2005 11:00 pm
Location: sheffield, s.yorks

Post Sat Jan 20, 2007 3:16 am

I'm collecting parts for this at the moment.

The bulkhead's will be the same, the pedal boxes swap over, but you may have to drill the bulkhead for the clutch master cylinder. you will also need to weld a bracket/mount on the o/s/f suspension turret (assuming it's rhd) for the clutch fluid resevoir.

A spigot bearing will also need to be pressed into the end of the crankshaft, and your propshaft will need swapping with the manual one as auto prop's are shorter

The starter inhbitor circuit will need to be removed, but this seems straightforward enough(do a seach).
Auto's are usually geared higher, so a diff swap may be in order too

It's not as straightforward as i first thought, but should be do-able in a weekend (I hope!!)

hope this helps
Templ8e30
E30 Zone Addict
E30 Zone Addict
Posts: 2801
Joined: Mon Jan 10, 2005 11:00 pm
Location: Ashton-under-Lyne, Lancashire

Post Sat Jan 20, 2007 4:52 pm

I converted one a couple of years back, needed the following:

Gearbox
Propshaft
Flywheel
Clutch
Spigot bearing and related cup/washer/felt ring
Gear linkages and mounting parts
Gear lever and gaiter
Pedal box
Clutch slave and master cylinders with piping and fluid reservoir with bracket
Gearbox mounting bolts (iirc they're different lengths)


Can't remember if the centre console is different or not.

There is a starter inhibit switch on auto's (stops you starting it whilst in gear), Brianmoore will be the expert on this as I can't remember which bits needed attention.

The rad is different as it has a cooling tube inside for the autobox, you can disconnect the pipework and use it as-is though.

You may want to change the diff too, it'll probably be a 3.73 on the auto.

Easy enough but time consuming.

Cheers,

Iain T
Image
2007 Mazda 6 2.0 estate
Political Correctness - A concept based on the idea that its possible to pick up a turd by the clean end !
daimlerman
**BANNED**
Posts: 15968
Joined: Mon Feb 27, 2006 11:00 pm
Location: Grumpy Old Man

Post Sat Jan 20, 2007 7:11 pm

Mac325i,If your diff is a 3.69 or there abouts I will be interested.My standard 320i manual needs higher gearing to suit the 2.7!!
mac325i
E30 Zone Newbie
E30 Zone Newbie
Posts: 116
Joined: Thu Jul 28, 2005 11:00 pm
Location: sheffield, s.yorks

Post Sat Jan 20, 2007 9:34 pm

daimlerman wrote:Mac325i,If your diff is a 3.69 or there abouts I will be interested.My standard 320i manual needs higher gearing to suit the 2.7!!
I've already replaced my diff with a 3.91 slipper, I'll dig the old one out tomorrow and get back to you with the ratio
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Sat Jan 20, 2007 10:49 pm

Templ8e30 wrote:I converted one a couple of years back, needed the following:

Gearbox
Propshaft
Flywheel
Clutch
Spigot bearing and related cup/washer/felt ring
Gear linkages and mounting parts
Gear lever and gaiter
Pedal box
Clutch slave and master cylinders with piping and fluid reservoir with bracket
Gearbox mounting bolts (iirc they're different lengths)


Can't remember if the centre console is different or not.

There is a starter inhibit switch on auto's (stops you starting it whilst in gear), Brianmoore will be the expert on this as I can't remember which bits needed attention.



Iain T
Add to the list: The short wiring loom for the reverse light switch to the connector at the bottom of the gearlever, inside the car.
Goes through the gear lever grommet, and may still be attached to it.
Centre console is the same, although there's a little metal bracket that has to be removed.
Starter inhibit: Above the glovebox you will find two black, round single pin connectors, each with black/yellow wire coming from the main loom.
Unplug the wiring from these two connectors and plug the two connectors from the main loom together. You can then remove the inhibit loom and its relay completely from the car.