Trying to get the rear beam out, but its being stubborn. I'm assuming that the two big vertical bolts are siezed. I've done them with wd40 from the top and it is finding its way down, is it Ok to twat these bolts upwards with a hammer to release the beam? I can't get a good spot to get any decent leverage downwards, petrol tank is in the way.
Cheers
Brian
Rear beam removal
Moderator: martauto
-
Brian28
- E30 Zone Squatter

- Posts: 1596
- Joined: Sat Jun 11, 2005 11:00 pm
- Location: Bournemouth
For sale - E30 320i racer project - sold.
-
stuartgallafant
- E30 Zone Addict

- Posts: 4531
- Joined: Tue Mar 29, 2005 11:00 pm
- Location: Costa del Croydon
undo the 22mm nut under the support plate, and remove the 2 6mm hex bolts to remove the plate
with a rubber mallet, twat the bolt through the car from underneath (make sure your rear bench is up!) and remove the bolt
then wiggle the f*ck out of the rear beam by putting something up the tube where the bolt was
remove handbrake cables and brakepipes, or even remove the calipers
undo the propshaft, and the rear axle should come away!!
with a rubber mallet, twat the bolt through the car from underneath (make sure your rear bench is up!) and remove the bolt
then wiggle the f*ck out of the rear beam by putting something up the tube where the bolt was
remove handbrake cables and brakepipes, or even remove the calipers
undo the propshaft, and the rear axle should come away!!
-
Templ8e30
- E30 Zone Addict

- Posts: 2801
- Joined: Mon Jan 10, 2005 11:00 pm
- Location: Ashton-under-Lyne, Lancashire
You may not be able to release the bolts, I had them sat on axle stands supporting the weight of the car whilst myself and 4 mates jumped in unison inside the car. No movement.
I ended up using a bearing puller to pull the beam and bushes down off the bolts.
Bitch of a job.
Cheers,
Iain T
I ended up using a bearing puller to pull the beam and bushes down off the bolts.
Bitch of a job.
Cheers,
Iain T

2007 Mazda 6 2.0 estate
Political Correctness - A concept based on the idea that its possible to pick up a turd by the clean end !
-
Ant
- Retired Team Member

- Posts: 10496
- Joined: Tue Dec 21, 2004 11:00 pm
- Location: PD+E dept :D
the tops of the bolts are sometimes covered over with mastic, if that is the case here, use something to remove all of it from inside the car, until you can see the bolts themselves.
you will not be able to force the bolts through the stuff, its very elastic
some heat on the bolts works wonders too, and will help the WD creep into the places it cant normally reach, capillary action baby
you will not be able to force the bolts through the stuff, its very elastic
some heat on the bolts works wonders too, and will help the WD creep into the places it cant normally reach, capillary action baby
Product Development and Endurance for Delphi.
Original performance chips, original works not unlicensed copies
Email FTW
Original performance chips, original works not unlicensed copies
-
Brian28
- E30 Zone Squatter

- Posts: 1596
- Joined: Sat Jun 11, 2005 11:00 pm
- Location: Bournemouth
Ok, thanks guys. I'm pretty much there Stuart, just wasn't sure if anything was f*ck-uppable if I tried to hammer the bolt upwards because the beam wasn't going anywhere. (Don't have a rubber mallet by the way so it'll be the sledgehammer
). So not a piece of cake then Ian. Ok, I'm off to try a bit more violent approach and see what happens.
Cheers
Brian
Cheers
Brian
For sale - E30 320i racer project - sold.
-
Brian28
- E30 Zone Squatter

- Posts: 1596
- Joined: Sat Jun 11, 2005 11:00 pm
- Location: Bournemouth
Thanks for that Ant, I just type too slow ....
For sale - E30 320i racer project - sold.

