Rear beam removal

Need technical Q/A then you're in the right place

Moderator: martauto

User avatar
Brian28
E30 Zone Squatter
E30 Zone Squatter
Posts: 1596
Joined: Sat Jun 11, 2005 11:00 pm
Location: Bournemouth

Post Sun Jan 14, 2007 12:45 pm

Trying to get the rear beam out, but its being stubborn. I'm assuming that the two big vertical bolts are siezed. I've done them with wd40 from the top and it is finding its way down, is it Ok to twat these bolts upwards with a hammer to release the beam? I can't get a good spot to get any decent leverage downwards, petrol tank is in the way.

Cheers
Brian
For sale - E30 320i racer project - sold.
stuartgallafant
E30 Zone Addict
E30 Zone Addict
Posts: 4531
Joined: Tue Mar 29, 2005 11:00 pm
Location: Costa del Croydon

Post Sun Jan 14, 2007 12:50 pm

undo the 22mm nut under the support plate, and remove the 2 6mm hex bolts to remove the plate

with a rubber mallet, twat the bolt through the car from underneath (make sure your rear bench is up!) and remove the bolt

then wiggle the f*ck out of the rear beam by putting something up the tube where the bolt was

remove handbrake cables and brakepipes, or even remove the calipers

undo the propshaft, and the rear axle should come away!!
Image
Templ8e30
E30 Zone Addict
E30 Zone Addict
Posts: 2801
Joined: Mon Jan 10, 2005 11:00 pm
Location: Ashton-under-Lyne, Lancashire

Post Sun Jan 14, 2007 1:12 pm

You may not be able to release the bolts, I had them sat on axle stands supporting the weight of the car whilst myself and 4 mates jumped in unison inside the car. No movement.

I ended up using a bearing puller to pull the beam and bushes down off the bolts.

Bitch of a job.

Cheers,

Iain T
Image
2007 Mazda 6 2.0 estate
Political Correctness - A concept based on the idea that its possible to pick up a turd by the clean end !
Ant
Retired Team Member
Retired Team Member
Posts: 10496
Joined: Tue Dec 21, 2004 11:00 pm
Location: PD+E dept :D

Post Sun Jan 14, 2007 1:42 pm

the tops of the bolts are sometimes covered over with mastic, if that is the case here, use something to remove all of it from inside the car, until you can see the bolts themselves.

you will not be able to force the bolts through the stuff, its very elastic

some heat on the bolts works wonders too, and will help the WD creep into the places it cant normally reach, capillary action baby :rock:
Product Development and Endurance for Delphi.

Original performance chips, original works not unlicensed copies :D Email FTW
User avatar
Brian28
E30 Zone Squatter
E30 Zone Squatter
Posts: 1596
Joined: Sat Jun 11, 2005 11:00 pm
Location: Bournemouth

Post Sun Jan 14, 2007 1:46 pm

Ok, thanks guys. I'm pretty much there Stuart, just wasn't sure if anything was f*ck-uppable if I tried to hammer the bolt upwards because the beam wasn't going anywhere. (Don't have a rubber mallet by the way so it'll be the sledgehammer :D ). So not a piece of cake then Ian. Ok, I'm off to try a bit more violent approach and see what happens.

Cheers
Brian
For sale - E30 320i racer project - sold.
User avatar
Brian28
E30 Zone Squatter
E30 Zone Squatter
Posts: 1596
Joined: Sat Jun 11, 2005 11:00 pm
Location: Bournemouth

Post Sun Jan 14, 2007 1:47 pm

Thanks for that Ant, I just type too slow ....
For sale - E30 320i racer project - sold.