spark plugs for high comp/hotter 2.7

Need technical Q/A then you're in the right place

Moderator: martauto

liam012
E30 Zone Camper
E30 Zone Camper
Posts: 1424
Joined: Sun Aug 28, 2005 11:00 pm

Post Mon Jan 08, 2007 8:21 pm

i am just curios really if anyine has any knowledge on the subject - im fairly sure that the comp ratio on my eta is 10.5:1 and wondering do i need to change the sparks to work better as its not a 325i which is what the bpr6es were for?

B= 14mm thread tpye
P= Projected insulator type plug
R= Resistor
6= Temp (2 hot --> 11 cold)
E= 19mm thread reach
S= standard 2.5mm centre electrode type

i presume the heat rating might be the one to experiment with and maybe even a shallower thread reach though i am out of my depth here and as i said just wondering if anyone is a bit of a wiz on the subject

ta
Image
Simon13
The longest resto in the world !
Posts: 22697
Joined: Mon Jan 10, 2005 11:00 pm
Location: Camberley, Surrey don't u know

Post Mon Jan 08, 2007 10:02 pm

I'd say Chrome bumper 325i ones

BPR6ES is their number, should run lovely with these, my alpina likes them
Turbo-Brown
Boost Junkie
Posts: 4705
Joined: Tue Feb 15, 2005 11:00 pm
Location: Aldershot, Hants

Post Mon Jan 08, 2007 10:11 pm

Wouldn't change the thread depth or you'll end up with either a shrouded plug or one that sticks out into the chamber.

Heat ranges, fine, fiddle with them :D
325i Twin Turbo (until 10am 01/12/07 :( )

www.air-in.co.uk free M20 exhaust and inlet flange
liam012
E30 Zone Camper
E30 Zone Camper
Posts: 1424
Joined: Sun Aug 28, 2005 11:00 pm

Post Mon Jan 08, 2007 11:38 pm

do you use a 0.8 gap on the alpina?
Image
User avatar
reggid
E30 Zone Squatter
E30 Zone Squatter
Posts: 1984
Joined: Mon Jul 11, 2005 11:00 pm
Location: Oz

Post Tue Jan 09, 2007 1:44 am

is the heat range the only difference between the chrome and plastic bumper e30 325i?

I have a higher comp m20b31 11:1 but with i am still running a cat :( , so should i use the bpr6es or the std ZGR5A ones? I am currently running bosch WR8LC (W8LCR) and have tried a cooler plug in the WR7DC+ but the engine seemed to run hotter (according to the coolant temp gauge and no wasn't expectin it to run cooler....lol) and didn't seem to be any better or worse in terms of responsiveness or driveability. There is no real problem with the WR8LC (AFAIK) other than that it doesn't make sense to use the same plugs when compression has increased 2.2 points so i just want to use a plug that is probably more suited to my application.
Turbo-Brown
Boost Junkie
Posts: 4705
Joined: Tue Feb 15, 2005 11:00 pm
Location: Aldershot, Hants

Post Tue Jan 09, 2007 8:12 am

Guess assuming you know the fueling's correct, you can whip the plugs out and see whether they're in the correct heat range :)

Only works if you know the fueling's right though.
325i Twin Turbo (until 10am 01/12/07 :( )

www.air-in.co.uk free M20 exhaust and inlet flange
d6dph
Married to the E30 Zone
Married to the E30 Zone
Posts: 12435
Joined: Sun Aug 14, 2005 11:00 pm
Location: Tiptree. Essex

Post Tue Jan 09, 2007 8:18 am

I have been running mine on ZGR5A (late model plugs) and I really didn't like the idle. Changed to BPR6ES and its so much nicer, silky smooth idle and seems to run a lot nicer. Maybe I just had a faulty ZGR plug? But I'd definately reccomend the chrome bumper model plugs.
Image
User avatar
reggid
E30 Zone Squatter
E30 Zone Squatter
Posts: 1984
Joined: Mon Jul 11, 2005 11:00 pm
Location: Oz

Post Tue Jan 09, 2007 8:26 am

Turbo-Brown wrote:Guess assuming you know the fueling's correct, you can whip the plugs out and see whether they're in the correct heat range :)

Only works if you know the fueling's right though.
what do i look for? Is it just the deposits light brown greyish sort of colour?
Won't the O2 sensor make it difficult to read the plugs?
Andyboy
Alpina Colada
Posts: 12577
Joined: Mon Sep 11, 2006 11:00 pm
Location: Notts

Post Tue Jan 09, 2007 4:44 pm

Use Bosch W7DCR's. The higher the compression, the higher the combustion temperatures so you'll need a cooler plug. These plugs were used in the original high compression 325i (chrome bumper like Simon13 says) and the Alpina C2 2.7. They are physically a similar plug to the later one but the ceramic core differs so that it dissipates more heat. As long as the fuelling and timing is correct, it's the spark plug that regulates the combustion chamber temperature - wrong plugs lose power.
Turbo-Brown
Boost Junkie
Posts: 4705
Joined: Tue Feb 15, 2005 11:00 pm
Location: Aldershot, Hants

Post Wed Jan 10, 2007 8:14 am

what do i look for? Is it just the deposits light brown greyish sort of colour?
Won't the O2 sensor make it difficult to read the plugs?
The O2 sensor should only make alterations to light/no load fueling so if you can kill the engine from high revs/load and have a look at the plugs you'll get a good idea of whether they're in the correct heat range.....assuming that the fueling's correct.

Think those piccies in the Haynes manuals assume that the plug's correct and the engine unmodified and therefore talk about the symptoms of incorrect fueling and their effect on the plugs.
325i Twin Turbo (until 10am 01/12/07 :( )

www.air-in.co.uk free M20 exhaust and inlet flange
User avatar
reggid
E30 Zone Squatter
E30 Zone Squatter
Posts: 1984
Joined: Mon Jul 11, 2005 11:00 pm
Location: Oz

Post Wed Jan 10, 2007 10:52 am

Turbo-Brown wrote:
what do i look for? Is it just the deposits light brown greyish sort of colour?
Won't the O2 sensor make it difficult to read the plugs?
The O2 sensor should only make alterations to light/no load fueling so if you can kill the engine from high revs/load and have a look at the plugs you'll get a good idea of whether they're in the correct heat range.....assuming that the fueling's correct.

Think those piccies in the Haynes manuals assume that the plug's correct and the engine unmodified and therefore talk about the symptoms of incorrect fueling and their effect on the plugs.
i had a look at the haynes manual and bosch plug brochure

http://www.bosch.com.au/content/languag ... tcover.pdf

and i have concluded that if they are glazed or have started burning away then engine is running too hot and as you say if the AFR is okay then the heat range is the likely cause.

i have used the WR8LC (revised W8LCR) and WR7DC+ (revised W7DCR) and both visually look the same but i will try them both again to see whats best