i am just curios really if anyine has any knowledge on the subject - im fairly sure that the comp ratio on my eta is 10.5:1 and wondering do i need to change the sparks to work better as its not a 325i which is what the bpr6es were for?
B= 14mm thread tpye
P= Projected insulator type plug
R= Resistor
6= Temp (2 hot --> 11 cold)
E= 19mm thread reach
S= standard 2.5mm centre electrode type
i presume the heat rating might be the one to experiment with and maybe even a shallower thread reach though i am out of my depth here and as i said just wondering if anyone is a bit of a wiz on the subject
ta
spark plugs for high comp/hotter 2.7
Moderator: martauto
-
Simon13
- The longest resto in the world !
- Posts: 22697
- Joined: Mon Jan 10, 2005 11:00 pm
- Location: Camberley, Surrey don't u know
I'd say Chrome bumper 325i ones
BPR6ES is their number, should run lovely with these, my alpina likes them
BPR6ES is their number, should run lovely with these, my alpina likes them
-
Turbo-Brown
- Boost Junkie
- Posts: 4705
- Joined: Tue Feb 15, 2005 11:00 pm
- Location: Aldershot, Hants
Wouldn't change the thread depth or you'll end up with either a shrouded plug or one that sticks out into the chamber.
Heat ranges, fine, fiddle with them
Heat ranges, fine, fiddle with them
-
liam012
- E30 Zone Camper

- Posts: 1424
- Joined: Sun Aug 28, 2005 11:00 pm
do you use a 0.8 gap on the alpina?

-
reggid
- E30 Zone Squatter

- Posts: 1984
- Joined: Mon Jul 11, 2005 11:00 pm
- Location: Oz
is the heat range the only difference between the chrome and plastic bumper e30 325i?
I have a higher comp m20b31 11:1 but with i am still running a cat
, so should i use the bpr6es or the std ZGR5A ones? I am currently running bosch WR8LC (W8LCR) and have tried a cooler plug in the WR7DC+ but the engine seemed to run hotter (according to the coolant temp gauge and no wasn't expectin it to run cooler....lol) and didn't seem to be any better or worse in terms of responsiveness or driveability. There is no real problem with the WR8LC (AFAIK) other than that it doesn't make sense to use the same plugs when compression has increased 2.2 points so i just want to use a plug that is probably more suited to my application.
I have a higher comp m20b31 11:1 but with i am still running a cat
-
Turbo-Brown
- Boost Junkie
- Posts: 4705
- Joined: Tue Feb 15, 2005 11:00 pm
- Location: Aldershot, Hants
Guess assuming you know the fueling's correct, you can whip the plugs out and see whether they're in the correct heat range 
Only works if you know the fueling's right though.
Only works if you know the fueling's right though.
-
d6dph
- Married to the E30 Zone

- Posts: 12435
- Joined: Sun Aug 14, 2005 11:00 pm
- Location: Tiptree. Essex
I have been running mine on ZGR5A (late model plugs) and I really didn't like the idle. Changed to BPR6ES and its so much nicer, silky smooth idle and seems to run a lot nicer. Maybe I just had a faulty ZGR plug? But I'd definately reccomend the chrome bumper model plugs.

-
reggid
- E30 Zone Squatter

- Posts: 1984
- Joined: Mon Jul 11, 2005 11:00 pm
- Location: Oz
what do i look for? Is it just the deposits light brown greyish sort of colour?Turbo-Brown wrote:Guess assuming you know the fueling's correct, you can whip the plugs out and see whether they're in the correct heat range
Only works if you know the fueling's right though.
Won't the O2 sensor make it difficult to read the plugs?
-
Andyboy
- Alpina Colada
- Posts: 12577
- Joined: Mon Sep 11, 2006 11:00 pm
- Location: Notts
Use Bosch W7DCR's. The higher the compression, the higher the combustion temperatures so you'll need a cooler plug. These plugs were used in the original high compression 325i (chrome bumper like Simon13 says) and the Alpina C2 2.7. They are physically a similar plug to the later one but the ceramic core differs so that it dissipates more heat. As long as the fuelling and timing is correct, it's the spark plug that regulates the combustion chamber temperature - wrong plugs lose power.
-
Turbo-Brown
- Boost Junkie
- Posts: 4705
- Joined: Tue Feb 15, 2005 11:00 pm
- Location: Aldershot, Hants
The O2 sensor should only make alterations to light/no load fueling so if you can kill the engine from high revs/load and have a look at the plugs you'll get a good idea of whether they're in the correct heat range.....assuming that the fueling's correct.what do i look for? Is it just the deposits light brown greyish sort of colour?
Won't the O2 sensor make it difficult to read the plugs?
Think those piccies in the Haynes manuals assume that the plug's correct and the engine unmodified and therefore talk about the symptoms of incorrect fueling and their effect on the plugs.
-
reggid
- E30 Zone Squatter

- Posts: 1984
- Joined: Mon Jul 11, 2005 11:00 pm
- Location: Oz
i had a look at the haynes manual and bosch plug brochureTurbo-Brown wrote:The O2 sensor should only make alterations to light/no load fueling so if you can kill the engine from high revs/load and have a look at the plugs you'll get a good idea of whether they're in the correct heat range.....assuming that the fueling's correct.what do i look for? Is it just the deposits light brown greyish sort of colour?
Won't the O2 sensor make it difficult to read the plugs?
Think those piccies in the Haynes manuals assume that the plug's correct and the engine unmodified and therefore talk about the symptoms of incorrect fueling and their effect on the plugs.
http://www.bosch.com.au/content/languag ... tcover.pdf
and i have concluded that if they are glazed or have started burning away then engine is running too hot and as you say if the AFR is okay then the heat range is the likely cause.
i have used the WR8LC (revised W8LCR) and WR7DC+ (revised W7DCR) and both visually look the same but i will try them both again to see whats best
