Need technical Q/A then you're in the right place
Moderator: martauto
-
iDreamBeemer
- E30 Zone Camper

- Posts: 1177
- Joined: Mon Feb 14, 2005 11:00 pm
- Location: Camberley
Post
Fri Dec 29, 2006 11:27 am
Well, broke my ebay cherry and managed to buy a tech2 wheel and pretty pleased.... here is a poor pic!
Going to replace the tech1 wheel on just now....
Am I right in thinking you need to take the badge off with something like a screw driver to get to the bolt behind or is there more to it?
-
Templ8e30
- E30 Zone Addict

- Posts: 2801
- Joined: Mon Jan 10, 2005 11:00 pm
- Location: Ashton-under-Lyne, Lancashire
Post
Fri Dec 29, 2006 11:36 am
Iirc the whole centre section pulls off (horn push).
See here:
http://www.realoem.com/bmw/showparts.do ... g=32&fg=35
Remember you'll need the key in the ignition turned to position 1 with the steering lock off or you won't be able to remove the old wheel.
Cheers,
Iain T

2007 Mazda 6 2.0 estate
Political Correctness - A concept based on the idea that its possible to pick up a turd by the clean end !
-
gooner1
- Out humping Reindeer
- Posts: 13280
- Joined: Fri Apr 14, 2006 11:00 pm
- Location: Northampton.For my sins.
Post
Fri Dec 29, 2006 11:44 am
And watch your nose when you pull wheel off mate.
-
iDreamBeemer
- E30 Zone Camper

- Posts: 1177
- Joined: Mon Feb 14, 2005 11:00 pm
- Location: Camberley
Post
Fri Dec 29, 2006 11:52 am
Iirc the whole centre section pulls off (horn push).
sorry, not clear enough! Its the tech1 wheel I wanted to know about, I can see easily enough on the new wheel!
-
Gortour
- E30 Zone Team Member

- Posts: 9025
- Joined: Sat Sep 23, 2006 11:00 pm
- Location: Poole, Dorset
Post
Fri Dec 29, 2006 11:56 am
I THINK the Tech one just removes the BMW badge from the centre as you first suggested.
Currently slumming it in an E46 Touring
-
OBs
- E30 Zone Squatter

- Posts: 1655
- Joined: Thu Nov 02, 2006 11:00 pm
- Location: Torbay, Devon
Post
Fri Dec 29, 2006 12:19 pm
Dreamer you selling your Tech 1 wheel mate is it a little one??
-
Dan318-is
- Married to the E30 Zone

- Posts: 8006
- Joined: Wed Jul 06, 2005 11:00 pm
- Location: Surrey/London
Post
Fri Dec 29, 2006 12:22 pm
Correct me if im wrong but i think that looks liek an e36 tec 2 wheel? the centre holds aim up at an angle rather than straight across liek the e30 ones?
on tec 1s the roundel pops of to expose the 22mm nut, on tec 2s the whole horn push assembly simply pushes off to expose it,
-
iDreamBeemer
- E30 Zone Camper

- Posts: 1177
- Joined: Mon Feb 14, 2005 11:00 pm
- Location: Camberley
Post
Fri Dec 29, 2006 12:39 pm
Dan - pretty sure its an e30 one - I measured it this morning and it is the 370mm smaller version. I understand the e36 were 385mm...
Dreamer you selling your Tech 1 wheel mate is it a little one??
They are the same size I think for tech 1s but no, not selling, I plan to be able to put the car back to original spec if I want to sell it so it is destined for the garden shed!
-
Dan318-is
- Married to the E30 Zone

- Posts: 8006
- Joined: Wed Jul 06, 2005 11:00 pm
- Location: Surrey/London
Post
Fri Dec 29, 2006 12:40 pm
only one way to find out mate! should only take five minutes to refit a new one go n give it a try!
-
OBs
- E30 Zone Squatter

- Posts: 1655
- Joined: Thu Nov 02, 2006 11:00 pm
- Location: Torbay, Devon
Post
Fri Dec 29, 2006 12:42 pm
They are the same size I think for tech 1s but no, not selling, I plan to be able to put the car back to original spec if I want to sell it so it is destined for the garden shed!
Bugger!
-
Templ8e30
- E30 Zone Addict

- Posts: 2801
- Joined: Mon Jan 10, 2005 11:00 pm
- Location: Ashton-under-Lyne, Lancashire
Post
Fri Dec 29, 2006 12:57 pm
iDreamBeemer wrote:Iirc the whole centre section pulls off (horn push).
sorry, not clear enough! Its the tech1 wheel I wanted to know about, I can see easily enough on the new wheel!
Yes sorry, the tech one requires the centre badge to be prised out with a small screwdriver
Cheers,
Iain T

2007 Mazda 6 2.0 estate
Political Correctness - A concept based on the idea that its possible to pick up a turd by the clean end !
-
iDreamBeemer
- E30 Zone Camper

- Posts: 1177
- Joined: Mon Feb 14, 2005 11:00 pm
- Location: Camberley
Post
Sat Dec 30, 2006 10:32 am
OK, the nut I can get too but not sure on what to do next - do I need the keys turned to position 1 to undo the nut? If so how the hell do you stop the steering wheel from turning?
spent a few minutes trying both ways and the nut wont budge (having been there for 16 years I can understand) any advices folks?
-
eko
- Old timer
- Posts: 11531
- Joined: Sat Feb 05, 2005 11:00 pm
- Location: South Devon
Post
Sat Dec 30, 2006 10:37 am
iDreamBeemer wrote:OK, the nut I can get too but not sure on what to do next - do I need the keys turned to position 1 to undo the nut? If so how the hell do you stop the steering wheel from turning?
spent a few minutes trying both ways and the nut wont budge (having been there for 16 years I can understand) any advices folks?
Martin,put the steering lock on(key removed) then loosen the nut,then insert key and turn to position 1 to remove the wheel!
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
Post
Sat Dec 30, 2006 10:41 am
Put the nut back on a few turns before you pull at the wheel. Saves a visit to A & E at a time of year when they are short staffed.
-
iDreamBeemer
- E30 Zone Camper

- Posts: 1177
- Joined: Mon Feb 14, 2005 11:00 pm
- Location: Camberley
Post
Sat Dec 30, 2006 10:44 am
cheers Brian and Tony, now all I need is some arm strength!! No long poles in the house!
Can I put wd40 on to try to loosen it a bit?
p.s. Tony have you sold your short shifter?
-
DaveD
- E30Zone Wiki Specialist
- Posts: 5129
- Joined: Tue Jan 11, 2005 11:00 pm
- Location: Sheffield
Post
Sat Dec 30, 2006 10:44 am
soak the nut in wd 40 ,,with the steering lock off get someone to hold the wheel while you turn the wrench anti clockwise or keep tapping it with a hammer (the wrench) while trying to turn it....you need 3 hands
best of luck
-
eko
- Old timer
- Posts: 11531
- Joined: Sat Feb 05, 2005 11:00 pm
- Location: South Devon
Post
Sat Dec 30, 2006 10:51 am
No Martin ive not sold it,its still in my car
Priced up the 2.8 one recently and its about £35,just had more important things to put that £35 into

-
iDreamBeemer
- E30 Zone Camper

- Posts: 1177
- Joined: Mon Feb 14, 2005 11:00 pm
- Location: Camberley
Post
Sat Dec 30, 2006 10:59 am

no worries Tony, just would hate to think I missed a bargain!! Understand its low on the priority list, got a few other things I have to sort out too (like the fecking paint!!)
just tried again and I think I am going to need some help, need to rope in a second pair of hands or a bigger socket wrench!! Could you use an air gun or is that a bad idea? Its not budging at all!
-
eko
- Old timer
- Posts: 11531
- Joined: Sat Feb 05, 2005 11:00 pm
- Location: South Devon
Post
Sat Dec 30, 2006 11:03 am
Martin have you tried undoing the nut with the key removed?
Some people might say its risky(putting strain on the column) but ive done loads like that and never had a problem!
Once the nut is `loose` you can insert the key and carry on as described

-
iDreamBeemer
- E30 Zone Camper

- Posts: 1177
- Joined: Mon Feb 14, 2005 11:00 pm
- Location: Camberley
Post
Sat Dec 30, 2006 11:08 am
Martin have you tried undoing the nut with the key removed?
Thats what I was doing, it was the only way I could get resistance to push against but the nut wont budge
-
eko
- Old timer
- Posts: 11531
- Joined: Sat Feb 05, 2005 11:00 pm
- Location: South Devon
Post
Sat Dec 30, 2006 11:10 am
iDreamBeemer wrote:Martin have you tried undoing the nut with the key removed?
Thats what I was doing, it was the only way I could get resistance to push against but the nut wont budge
ah right
What size ratchet are you using then?
You got nothing to hand to slide over the end of the ratchet to extend it?
Piece of tubing/pipe etc?
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
Post
Sat Dec 30, 2006 11:13 am
Can't see WD40 helping much, as it isn't going to be a rust problem. Should be tight (79Nm), but not THAT tight.
Agree with not putting too much strain on the steering lock. Get someone to hold the wheel as well.
-
iDreamBeemer
- E30 Zone Camper

- Posts: 1177
- Joined: Mon Feb 14, 2005 11:00 pm
- Location: Camberley
Post
Sat Dec 30, 2006 11:19 am
quite a short small ratchet, no tubing though, have bashed it a couple of times with a hammer but I dont want to be too rough and damage the rest of the steering!
No rust there at all, but does look like some white paint on it.....?
Will need to find a friend to hold the wheel! but that will have to be a bit later on....might try to see if I can get some tubing or borrow a bigger ratchet and see how I get on.
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
Post
Sat Dec 30, 2006 11:22 am
Ratchet? Ratchets aren't for tightening or loosening fasteners; they're for removing them once they're loose. It's too tight for a ratchet. You need a cracker bar or at least a sliding T bar.
Last edited by Brianmoooore on Sat Dec 30, 2006 11:24 am, edited 1 time in total.
-
iDreamBeemer
- E30 Zone Camper

- Posts: 1177
- Joined: Mon Feb 14, 2005 11:00 pm
- Location: Camberley
Post
Sat Dec 30, 2006 11:23 am
You need a cracker bar or at least a sliding T bar
pardon? not got a lot a tools and pretty sure I dont have either of those!!!
-
benjy
- E30 Zone Regular

- Posts: 662
- Joined: Mon Jan 02, 2006 11:00 pm
- Location: English Riviera
Post
Sat Dec 30, 2006 11:28 am
Three Weetabix's mate and dedication thats all you need!! Seriously tho, it just takes a bit of muscule/weight on it. If its never been off then it will be tight and will prob have the remains of thread lock holding on...........
Gaffa tape is like "the force" - it has a light side, a dark side, and it holds the universe together.
There's nothing that shouts "Poor Workmanship" more than wrinkles in the Gaffer tap
-
Gortour
- E30 Zone Team Member

- Posts: 9025
- Joined: Sat Sep 23, 2006 11:00 pm
- Location: Poole, Dorset
Post
Sat Dec 30, 2006 11:33 am
I have a 4-bar wheel brace, very handy for such things. Just needs an end with a 22mm on it.
Also bought one of those extending bars for wheel nuts a while ago for about £3, comes with a reversible 17mm / 19mm head, but it's a standard 1/2" socket end, so a 22mm socket would fit no problem.
Currently slumming it in an E46 Touring
-
iil325i
- E30 Zone Regular

- Posts: 589
- Joined: Fri May 06, 2005 11:00 pm
- Location: cambs
Post
Sat Dec 30, 2006 11:44 am
check the indercaters are terned off when you put the new wheels on as you will brake the bit that turns them off when you turn the wheel, and thats a pain in the ass.
go get a braker bar there only like £10 for a s**t one, then keep it in the car. you can beat chavs with it if they cut you up

-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
Post
Sat Dec 30, 2006 11:55 am
iil325i wrote:
go get a braker bar there only like £10 for a s**t one, then keep it in the car. you can beat chavs with it if they cut you up

One of those extendable wheel nut breaker bars would do, and is a useful addition to any car boot.
The one I acquired has a reversible 1/2" socket on it, that comes off to leave a useful cracker bar.
-
iil325i
- E30 Zone Regular

- Posts: 589
- Joined: Fri May 06, 2005 11:00 pm
- Location: cambs
Post
Sat Dec 30, 2006 12:05 pm
yer i have one of them as well you can get these for well under s 5er now.
-
Gortour
- E30 Zone Team Member

- Posts: 9025
- Joined: Sat Sep 23, 2006 11:00 pm
- Location: Poole, Dorset
Post
Sat Dec 30, 2006 12:47 pm
Brianmoooore wrote:One of those extendable wheel nut breaker bars would do, and is a useful addition to any car boot.
The one I acquired has a reversible 1/2" socket on it, that comes off to leave a useful cracker bar.
Yup, that's the one I have. Very good it is too, and being standard 1/2" it has even more uses. Well worth £3...
Currently slumming it in an E46 Touring