dropping an engine out

Need technical Q/A then you're in the right place

Moderator: martauto

User avatar
gazza
E30 Zone Camper
E30 Zone Camper
Posts: 1266
Joined: Tue Feb 08, 2005 11:00 pm
Location: north london/herts

Post Sun Dec 24, 2006 4:11 pm

as above going to do a swop next week ive pulled them out the top before
but never from the bottom (oooh) i have removed the subframe before. is there anything i have to watch out for or tips ie wheels on or off or leave it all on a jack or should i support the engine and box seperately...it seems easier as i want to swop the suspension at the same time and i dont have to change springs/power steerring pipes(its going into a 318)

also when its out is it easy to move around so i can gunk it all down and give it a lick of paint to tidy it up (nice misty buff i think)
mybmw6
E30 Zone Newbie
E30 Zone Newbie
Posts: 153
Joined: Tue Sep 20, 2005 11:00 pm

Post Tue Dec 26, 2006 1:13 am

I took my 325i engine out from underneath. For me and the tools I had it worked out easier. I removed my wheels (much easier to do while on the car rather than later), but left the engine on the subframe. The guy helping me made up some brackets to fit on the shock mounts and we lifted the car using a chain hoist and dropped the engine onto a welded up rolling frame.

Before the engine came out I removed the exhaust from Manifold down, disconnected the driveshaft, removed all the ancillaries p/s a/c etc and left them on the car along with the loom. I was putting in a new camshaft and fixing some steering rack and gearbox issues, the engine was coming out and going back in. I left the gearbox attached to the engine.

Hope this is of some helps.
Matt
DanThe
E30 Zone Team Member
E30 Zone Team Member
Posts: 28649
Joined: Sat Sep 10, 2005 11:00 pm
Location: Staffs

Post Tue Dec 26, 2006 11:00 am

A small frame on castor wheels is best, like the type bread vans use winkeye

Wheels off, dissconnect brake lines from calipers, abs etc, exhaust frontpipe, prop, gearbox mount, pull ecu harness through and dissconnect loom in the usual way, dissconnect steering UJ from rack, remove strut top mounting nuts and subframe mounting bolts then jack the car over the engine and slide out from underneath or if the car is scrap then cut the front panel and cross member out which will make the job oh so much easier 8)
User avatar
gazza
E30 Zone Camper
E30 Zone Camper
Posts: 1266
Joined: Tue Feb 08, 2005 11:00 pm
Location: north london/herts

Post Tue Dec 26, 2006 7:24 pm

cheers so would you support the engine and lift the body off the subframe and drop the next body straight on top and bolt up the bits
DanThe
E30 Zone Team Member
E30 Zone Team Member
Posts: 28649
Joined: Sat Sep 10, 2005 11:00 pm
Location: Staffs

Post Wed Dec 27, 2006 12:23 am

Yep, thats how I always do it
seanboy
E30 Zone Regular
E30 Zone Regular
Posts: 642
Joined: Mon Aug 21, 2006 11:00 pm
Location: Beckenham

Post Wed Dec 27, 2006 12:33 am

Just wondering,If you had an engine crane would you be able to just lift the engine and gearbox out or is there more to it. got to go underneath the car, pulling car over engine while supporting the engine or taking off front of car if its scrap all good ways but wondering about the crane. get cheap discount at hss and not putting anything back in. cheers
DanThe
E30 Zone Team Member
E30 Zone Team Member
Posts: 28649
Joined: Sat Sep 10, 2005 11:00 pm
Location: Staffs

Post Wed Dec 27, 2006 12:53 am

Ive got a crane, its just a pain with 6 pots and if the suspension is coming off to be changed over then why bother with the crane
User avatar
gazza
E30 Zone Camper
E30 Zone Camper
Posts: 1266
Joined: Tue Feb 08, 2005 11:00 pm
Location: north london/herts

Post Wed Dec 27, 2006 2:27 pm

dan how would you lift the body ....jack on each chassis member or jack and beam of wood sounds like i need a few jacks but if i support the engine on blocks maybe it would be easier
DanThe
E30 Zone Team Member
E30 Zone Team Member
Posts: 28649
Joined: Sat Sep 10, 2005 11:00 pm
Location: Staffs

Post Wed Dec 27, 2006 2:38 pm

Heres a pic of the 4 pot coming out of mine

Image

I think I had a piece of 4x2 accross the 2 jacks but cant really remember.
User avatar
gazza
E30 Zone Camper
E30 Zone Camper
Posts: 1266
Joined: Tue Feb 08, 2005 11:00 pm
Location: north london/herts

Post Wed Dec 27, 2006 2:54 pm

right sorted one last question when re fitting does the body come down to the floor and you bolt up the struts and lift the lump up and allign all the bolts and bits
DanThe
E30 Zone Team Member
E30 Zone Team Member
Posts: 28649
Joined: Sat Sep 10, 2005 11:00 pm
Location: Staffs

Post Wed Dec 27, 2006 3:06 pm

Yes, you will need to have something underneath the lump, on castors is best so you can move it about.