H/lamp wiper motor

Need technical Q/A then you're in the right place

Moderator: martauto

jcjdavis1
E30 Zone Camper
E30 Zone Camper
Posts: 1128
Joined: Thu Apr 13, 2006 11:00 pm
Location: Paisley Scotland

Post Sun Dec 24, 2006 10:07 am

Hi Is the motor fooked if not how doe's it come out to clean/grease.
PS I know the pic is a bit big

Image
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Sun Dec 24, 2006 10:51 am

I've only ever had to throw away one motor that was beyond repair, and that was because the steel motor casing had rusted right away.
Yours looks non too clever in the picture, but as long as there's still enough case to locate the magnets, then it should go again.
First thing to remove is the output shaft/pinion gear and the rack that goes from it to the plastic gear behind the plate. This is the shaft that seizes and causes the wipers to quit, so it might take some time and effort to remove it.
After these are removed, the metal plate unclips and the rest is obvious.
jcjdavis1
E30 Zone Camper
E30 Zone Camper
Posts: 1128
Joined: Thu Apr 13, 2006 11:00 pm
Location: Paisley Scotland

Post Sun Dec 24, 2006 4:44 pm

hi brian is it a case of prying off the spindle at the front with plenty of wd40, elbow grease and mole grips. i have taken all the nuts and bolts off the spindle.

MERRY CHRISTMAS
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Sun Dec 24, 2006 6:43 pm

Spindle comes out backwards through the motor, and yes, it's a matter of getting a little movement and then working in WD40 untill it all comes free.
Put a wiper arm back on to turn the shaft, but don't turn hard enough to break the arm or strip the splines. If you do have to resort to grips as well, you'll have to clean up the damage on the shaft before it'll go back through the bush.
jcjdavis1
E30 Zone Camper
E30 Zone Camper
Posts: 1128
Joined: Thu Apr 13, 2006 11:00 pm
Location: Paisley Scotland

Post Tue Dec 26, 2006 4:43 pm

Hi casing on motor has hole in it so that one is binned,taken of n/s one,motor casing ok but having trouble removing spindle.Looks like I will be visiting the wanted section.thanks for the help.
Image
noney82
E30 Zone Camper
E30 Zone Camper
Posts: 1102
Joined: Thu Apr 27, 2006 11:00 pm
Location: manchester, stockport

Post Tue Dec 26, 2006 4:46 pm

what was the point behind these wipers
jcjdavis1
E30 Zone Camper
E30 Zone Camper
Posts: 1128
Joined: Thu Apr 13, 2006 11:00 pm
Location: Paisley Scotland

Post Tue Dec 26, 2006 5:32 pm

Headlamp wipers
Image
Simon
E30 Zone Team Member
E30 Zone Team Member
Posts: 14939
Joined: Sun Jan 09, 2005 11:00 pm
Location: South Wales

Post Tue Dec 26, 2006 7:44 pm

noney82 wrote:what was the point behind these wipers
To keep the headlamps clean!

They are actually very effective, especially at this time of year with the build up of salt on the car.

After a drive in the mildy wet current conditions, try parking up against a wall, clean one headlamp and then compare light outputs on the wall between the clean one and the dirty lamp, the results will probably shock you.
Image
beardymat
E30 Zone Squatter
E30 Zone Squatter
Posts: 1979
Joined: Tue Jun 14, 2005 11:00 pm
Location: sheffield, city of steel, and rust apparently

Post Tue Dec 26, 2006 7:55 pm

noney82 wrote:what was the point behind these wipers
plus you get extra kudos for working ones
No longer self employed but still available for welding duties.
noney82
E30 Zone Camper
E30 Zone Camper
Posts: 1102
Joined: Thu Apr 27, 2006 11:00 pm
Location: manchester, stockport

Post Tue Dec 26, 2006 9:00 pm

fair comments guys, i took mine off not like the looks, just need to test them for a fellow zoner.
noney82
E30 Zone Camper
E30 Zone Camper
Posts: 1102
Joined: Thu Apr 27, 2006 11:00 pm
Location: manchester, stockport

Post Fri Jan 12, 2007 6:06 pm

tested them the both work