Odd looking bolts in dizzy cap / thermo housing...

Need technical Q/A then you're in the right place

Moderator: martauto

User avatar
Royalratch
E30 Zone Addict
E30 Zone Addict
Posts: 4921
Joined: Sat Oct 21, 2006 11:00 pm
Location: London

Post Mon Dec 18, 2006 10:32 am

318i/M40 engine.

Another 10 min job stretching into days...:eek:

Took all bolts off thermostat housing - 2 bolt heads sheared off and stuck in the head/block.

The question is, I'm not sure I have enough room to use a tap+dye set without removing the head/engine? The offending area is facing the radioator with maybe 10 inches max if space.

I'm replacing the engine in Jan/Feb anyway so should I just put as many bolts back on as I can with a load of gasket seal and see if it makes it?

The other thing is, I noticed 2 of the distirbutor cap housing bolts have sheared too - they are odd looking long bolts with only a couple mm's of thread at the very end. BMW can't seem to find these bolts with what looks like the correct part number or even when they check the microfilm archive against a sketch from me.

I 'think' I need the bolts that go in the highlighted:
Image

Also (not sure) is the highlited area below the distributor cap housing and it's mounting bolt (item 21)?
Image

Am I reading these diagramns wrong? Are this correct?
Both these problems are keeping the car off the road and it sucks...

As always, much appreciated.
Martinaston
E30 Zone Addict
E30 Zone Addict
Posts: 3749
Joined: Mon Mar 14, 2005 11:00 pm
Location: London

Post Mon Dec 18, 2006 10:49 am

The top pic is the small bolts that come with a new dizzy cap, the bottom one is just a standard bolt.
There is NO nucleus.
User avatar
Royalratch
E30 Zone Addict
E30 Zone Addict
Posts: 4921
Joined: Sat Oct 21, 2006 11:00 pm
Location: London

Post Mon Dec 18, 2006 10:57 am

If I need to replace some dizzy cap bolts that have sheared/fallen off, what do use?

Can I use a alternative bolts? I'm guessing from looking at them they would be M4 x 50mm at least.
smithy318i
Engaged to the E30 Zone
Engaged to the E30 Zone
Posts: 5797
Joined: Thu Apr 28, 2005 11:00 pm
Location: Tyne & Wear

Post Mon Dec 18, 2006 11:51 am

You can probably get enough space inside the engine bay by removing the radiator and cowl.

You wont be able to bolt the thermostat housing on propperly without using all of the bolt holes. It will just leak as soon as the pressure builds up.

Parts 21 isn't one of the dizzy cap bolts. The dizzy bolts are attached to the cap when you buy it.
Image
User avatar
Royalratch
E30 Zone Addict
E30 Zone Addict
Posts: 4921
Joined: Sat Oct 21, 2006 11:00 pm
Location: London

Post Mon Dec 18, 2006 1:14 pm

So I can't get dizzy bolts without ordering the whole part?

Can I use a substitute?
smithy318i
Engaged to the E30 Zone
Engaged to the E30 Zone
Posts: 5797
Joined: Thu Apr 28, 2005 11:00 pm
Location: Tyne & Wear

Post Mon Dec 18, 2006 1:21 pm

Royalratch wrote:Can I use a substitute?
probably. im sure you have a tub of nuts/bolts/screws you could fish around in (or know someone who has) to find a replacement
Image