Intermittant speedo and mpg indicator?

Need technical Q/A then you're in the right place

Moderator: martauto

User avatar
bigjprogs
E30 Zone Newbie
E30 Zone Newbie
Posts: 16
Joined: Wed Aug 02, 2006 11:00 pm

Post Sun Dec 17, 2006 9:55 pm

Can anybody suggest a reason for my speedo and fuel consumption gauge dropping back to zero and then suddenly springing back to life for a few minutes before the same thing happens again! Noticed this yesterday for the first time after going along at about 65-70 on the M25 for about half an hour? Seems to operate normally at lower speeds? any help much appreciated-john.
User avatar
orangecurry
E30 Zone Addict
E30 Zone Addict
Posts: 2518
Joined: Mon Apr 11, 2005 11:00 pm
Location: West Sussex

Post Sun Dec 17, 2006 9:57 pm

wires from the diff speedo sensor will be broken inside the plastic covering - replace as much as you can from the sensor forward to where the cable enters the car body...

was I first?

seems I was :D

the wires get damaged due to mechanical wear (being over the back axle)

Well at least that was the reason for my speedo going intermittent (the wires inside the plastic sleeve although broken still touch some of the time) and then stopping altogether.
User avatar
bigjprogs
E30 Zone Newbie
E30 Zone Newbie
Posts: 16
Joined: Wed Aug 02, 2006 11:00 pm

Post Sun Dec 17, 2006 10:01 pm

Many thanks,Yes you were the first!!! If the wires were broken would'nt the fault be permanent and not intermittent?
fuzzy
He who sleeps with "Gingers"
Posts: 14351
Joined: Sat Jun 04, 2005 11:00 pm
Location: melbourne Australia

Post Sun Dec 17, 2006 10:10 pm

it might be broken but still making occasional contact on bumps or the other way around,mine did for ages and was the wire right at the back of the diff as it attached to the sensor.
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Sun Dec 17, 2006 10:44 pm

Copper becomes soft and flexible after it is heated and then allowed to cool slowly. If the copper is then bent a few times it becomes "work hardened" and more brittle, and can only be restored to the flexible state by heating again.
The wire to the diff suffers from vibration which causes this hardening, and it eventually breaks inside the plastic sheath, occasionally making contact again when the ends touch.
This is why the section of wire should be replaced rather than repaired.
User avatar
orangecurry
E30 Zone Addict
E30 Zone Addict
Posts: 2518
Joined: Mon Apr 11, 2005 11:00 pm
Location: West Sussex

Post Sun Dec 17, 2006 10:49 pm

who would have thought you would go over 8000 posts explaining about the intermittent speedo, Brian?

winkeye winkeye winkeye
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Sun Dec 17, 2006 11:06 pm

Been looking for things to post on all evening!
Morat
E30 Zone Team Member
E30 Zone Team Member
Posts: 8943
Joined: Thu Feb 09, 2006 11:00 pm
Location: The Peoples Republic of Yorkshire

Post Mon Dec 18, 2006 9:30 am

Well, I'm going to leave my car alone until Brian is getting near 10k posts :)
E30 Touring 0.35 cD - more slippery than prison soap :)

Image
Praise the Lard... and pass the dripping!
User avatar
bigjprogs
E30 Zone Newbie
E30 Zone Newbie
Posts: 16
Joined: Wed Aug 02, 2006 11:00 pm

Post Wed Dec 20, 2006 8:54 pm

MANY THANKS FOR EVERYBODY'S HELP,MUCH APPRECIATED-

JOHN :) :D