Intermittant speedo and mpg indicator?
Moderator: martauto
-
bigjprogs
- E30 Zone Newbie

- Posts: 16
- Joined: Wed Aug 02, 2006 11:00 pm
Can anybody suggest a reason for my speedo and fuel consumption gauge dropping back to zero and then suddenly springing back to life for a few minutes before the same thing happens again! Noticed this yesterday for the first time after going along at about 65-70 on the M25 for about half an hour? Seems to operate normally at lower speeds? any help much appreciated-john.
-
orangecurry
- E30 Zone Addict

- Posts: 2518
- Joined: Mon Apr 11, 2005 11:00 pm
- Location: West Sussex
wires from the diff speedo sensor will be broken inside the plastic covering - replace as much as you can from the sensor forward to where the cable enters the car body...
was I first?
seems I was
the wires get damaged due to mechanical wear (being over the back axle)
Well at least that was the reason for my speedo going intermittent (the wires inside the plastic sleeve although broken still touch some of the time) and then stopping altogether.
was I first?
seems I was
the wires get damaged due to mechanical wear (being over the back axle)
Well at least that was the reason for my speedo going intermittent (the wires inside the plastic sleeve although broken still touch some of the time) and then stopping altogether.
-
bigjprogs
- E30 Zone Newbie

- Posts: 16
- Joined: Wed Aug 02, 2006 11:00 pm
Many thanks,Yes you were the first!!! If the wires were broken would'nt the fault be permanent and not intermittent?
-
fuzzy
- He who sleeps with "Gingers"
- Posts: 14351
- Joined: Sat Jun 04, 2005 11:00 pm
- Location: melbourne Australia
it might be broken but still making occasional contact on bumps or the other way around,mine did for ages and was the wire right at the back of the diff as it attached to the sensor.
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
Copper becomes soft and flexible after it is heated and then allowed to cool slowly. If the copper is then bent a few times it becomes "work hardened" and more brittle, and can only be restored to the flexible state by heating again.
The wire to the diff suffers from vibration which causes this hardening, and it eventually breaks inside the plastic sheath, occasionally making contact again when the ends touch.
This is why the section of wire should be replaced rather than repaired.
The wire to the diff suffers from vibration which causes this hardening, and it eventually breaks inside the plastic sheath, occasionally making contact again when the ends touch.
This is why the section of wire should be replaced rather than repaired.
-
orangecurry
- E30 Zone Addict

- Posts: 2518
- Joined: Mon Apr 11, 2005 11:00 pm
- Location: West Sussex
who would have thought you would go over 8000 posts explaining about the intermittent speedo, Brian?

-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
Been looking for things to post on all evening!
-
Morat
- E30 Zone Team Member

- Posts: 8943
- Joined: Thu Feb 09, 2006 11:00 pm
- Location: The Peoples Republic of Yorkshire
Well, I'm going to leave my car alone until Brian is getting near 10k posts 
E30 Touring 0.35 cD - more slippery than prison soap 

Praise the Lard... and pass the dripping!

Praise the Lard... and pass the dripping!
-
bigjprogs
- E30 Zone Newbie

- Posts: 16
- Joined: Wed Aug 02, 2006 11:00 pm
MANY THANKS FOR EVERYBODY'S HELP,MUCH APPRECIATED-
JOHN

JOHN
