Rebuild diff?
Moderator: martauto
-
bennyboy
- E30 Zone Newbie

- Posts: 218
- Joined: Mon Jan 10, 2005 11:00 pm
- Location: West Sussex
Just last week my diff failed on my cab. it screamed when i came off the power with it gear but was ok when being driven. i spoke to a gearbox specialist and he reckons that it is the bearings as the crown wheel and pinion rarely fail. he can replace them all for £400+vat. at the moment i have put a spare diff on but it doesnt sound too clever and its a 4,10. i prefer my original 4,27.
i rang the stealers today and can get all the bearings for £110-£120 approx.
Shall i rebuild it myself?
Also, the gearbox bloke said that he had a second hand lsd cage/unit for about £150. Is it worth buying this too and fitting at the same time as rebuild? For £270 i could have a 4,27 lsd with all new bearings.
i rang the stealers today and can get all the bearings for £110-£120 approx.
Shall i rebuild it myself?
Also, the gearbox bloke said that he had a second hand lsd cage/unit for about £150. Is it worth buying this too and fitting at the same time as rebuild? For £270 i could have a 4,27 lsd with all new bearings.

16V IS engine!!!
-
stuartgallafant
- E30 Zone Addict

- Posts: 4531
- Joined: Tue Mar 29, 2005 11:00 pm
- Location: Costa del Croydon
-
bennyboy
- E30 Zone Newbie

- Posts: 218
- Joined: Mon Jan 10, 2005 11:00 pm
- Location: West Sussex
Cheers Stu. Think i might!
Has anybody else had a diff fail on them? if you have, What failed?
As i say the noise was quite loud and only on deceleration when in gear. does it sound like bearings? Just dont want to go spending a load of money on it when its something else thats fcuked!
Has anybody else had a diff fail on them? if you have, What failed?
As i say the noise was quite loud and only on deceleration when in gear. does it sound like bearings? Just dont want to go spending a load of money on it when its something else thats fcuked!

16V IS engine!!!
-
Chris-W
- E30 Zone Team Member

- Posts: 7219
- Joined: Tue May 24, 2005 11:00 pm
- Location: South Cheshire
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
E30 diffs have preloads and clearances to set up, which requires specialist equipment of the kind only specialist diff re builders are likely to have.
Not quite as simple as just replacing the seals and bearings.
Not quite as simple as just replacing the seals and bearings.
-
Chris-W
- E30 Zone Team Member

- Posts: 7219
- Joined: Tue May 24, 2005 11:00 pm
- Location: South Cheshire
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
On the other hand, Colin Chapman used to put non matching crown wheels and pinions together in diffs and add grinding paste, and he was a fairly successful engineer!
-
Chris-W
- E30 Zone Team Member

- Posts: 7219
- Joined: Tue May 24, 2005 11:00 pm
- Location: South Cheshire
-
Speedtouch
- Old Skooler

- Posts: 14129
- Joined: Tue Feb 14, 2006 11:00 pm
- Location: Canterbury
I had a diff go very noisy after high mileage, it turned out to be worn case-hardening on the pinion teeth.
No amount of sawdust, etc. would quieten it.
No amount of sawdust, etc. would quieten it.
///M aurice
ECU Upgrade EPROM Chips, £40 posted within the UK. Note these are not Zone chips.
viewtopic.php?f=6&t=279421
ECU Upgrade EPROM Chips, £40 posted within the UK. Note these are not Zone chips.
viewtopic.php?f=6&t=279421
-
bennyboy
- E30 Zone Newbie

- Posts: 218
- Joined: Mon Jan 10, 2005 11:00 pm
- Location: West Sussex
just taken the diff apart and its the input shaft bearings that have gone. £70 will get me the two bearings on this shaft. Shall i take this on my self?

16V IS engine!!!
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
Brianmoooore wrote:E30 diffs have preloads and clearances to set up, which requires specialist equipment of the kind only specialist diff re builders are likely to have.
Not quite as simple as just replacing the seals and bearings.
-
stuartgallafant
- E30 Zone Addict

- Posts: 4531
- Joined: Tue Mar 29, 2005 11:00 pm
- Location: Costa del Croydon
-
Templ8e30
- E30 Zone Addict

- Posts: 2801
- Joined: Mon Jan 10, 2005 11:00 pm
- Location: Ashton-under-Lyne, Lancashire
If you've never worked with feeler guages, peelable shims, micrometers and engineers blue to get the correct clearances and wear patterns I wouldn't bother.
It'd be cheaper and a lot less hassle to get a good second hand diff.
I have rebuilt a medium case diff before and I spent all weekend setting it up.
You'll find it very frustrating and you'll probably never be happy with the results.
Forget it.
Cheers,
Iain T
It'd be cheaper and a lot less hassle to get a good second hand diff.
I have rebuilt a medium case diff before and I spent all weekend setting it up.
You'll find it very frustrating and you'll probably never be happy with the results.
Forget it.
Cheers,
Iain T

2007 Mazda 6 2.0 estate
Political Correctness - A concept based on the idea that its possible to pick up a turd by the clean end !
-
stuartgallafant
- E30 Zone Addict

- Posts: 4531
- Joined: Tue Mar 29, 2005 11:00 pm
- Location: Costa del Croydon
-
bennyboy
- E30 Zone Newbie

- Posts: 218
- Joined: Mon Jan 10, 2005 11:00 pm
- Location: West Sussex
yeah thanks. im just very impatient and thought bearings would be the quickest way. Thanks for pointing out how much work is needed for the job. i nearly jumped right in the deep end!
Anyway, i rang BMC(bmparts) as they have a '93 318i cab with 66k which will have the 4,27 ratio diff i want. £60+vat. I get it tuesday!!!
Thanls everyone, for saving me!
Anyway, i rang BMC(bmparts) as they have a '93 318i cab with 66k which will have the 4,27 ratio diff i want. £60+vat. I get it tuesday!!!
Thanls everyone, for saving me!

16V IS engine!!!
-
stuartgallafant
- E30 Zone Addict

- Posts: 4531
- Joined: Tue Mar 29, 2005 11:00 pm
- Location: Costa del Croydon


