Rebuild diff?

Need technical Q/A then you're in the right place

Moderator: martauto

bennyboy
E30 Zone Newbie
E30 Zone Newbie
Posts: 218
Joined: Mon Jan 10, 2005 11:00 pm
Location: West Sussex

Post Thu Dec 14, 2006 6:38 pm

Just last week my diff failed on my cab. it screamed when i came off the power with it gear but was ok when being driven. i spoke to a gearbox specialist and he reckons that it is the bearings as the crown wheel and pinion rarely fail. he can replace them all for £400+vat. at the moment i have put a spare diff on but it doesnt sound too clever and its a 4,10. i prefer my original 4,27.
i rang the stealers today and can get all the bearings for £110-£120 approx.
Shall i rebuild it myself?
Also, the gearbox bloke said that he had a second hand lsd cage/unit for about £150. Is it worth buying this too and fitting at the same time as rebuild? For £270 i could have a 4,27 lsd with all new bearings.
Image
16V IS engine!!!
stuartgallafant
E30 Zone Addict
E30 Zone Addict
Posts: 4531
Joined: Tue Mar 29, 2005 11:00 pm
Location: Costa del Croydon

Post Thu Dec 14, 2006 8:33 pm

do it mate, i bloody would!!!
Image
bennyboy
E30 Zone Newbie
E30 Zone Newbie
Posts: 218
Joined: Mon Jan 10, 2005 11:00 pm
Location: West Sussex

Post Thu Dec 14, 2006 8:52 pm

Cheers Stu. Think i might!
Has anybody else had a diff fail on them? if you have, What failed?
As i say the noise was quite loud and only on deceleration when in gear. does it sound like bearings? Just dont want to go spending a load of money on it when its something else thats fcuked!
Image
16V IS engine!!!
Chris-W
E30 Zone Team Member
E30 Zone Team Member
Posts: 7219
Joined: Tue May 24, 2005 11:00 pm
Location: South Cheshire

Post Thu Dec 14, 2006 9:41 pm

Sounds like diff bearings indeed - just replaced the front diff today on our Range Rover for exactly the same symptoms.
Image
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Thu Dec 14, 2006 9:53 pm

E30 diffs have preloads and clearances to set up, which requires specialist equipment of the kind only specialist diff re builders are likely to have.
Not quite as simple as just replacing the seals and bearings.
Chris-W
E30 Zone Team Member
E30 Zone Team Member
Posts: 7219
Joined: Tue May 24, 2005 11:00 pm
Location: South Cheshire

Post Thu Dec 14, 2006 9:56 pm

Quite right - I should have pointed out that I made no attempt to remedy the duff diff, and fitted a professionally re-built unit.
Image
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Thu Dec 14, 2006 9:59 pm

On the other hand, Colin Chapman used to put non matching crown wheels and pinions together in diffs and add grinding paste, and he was a fairly successful engineer!
Chris-W
E30 Zone Team Member
E30 Zone Team Member
Posts: 7219
Joined: Tue May 24, 2005 11:00 pm
Location: South Cheshire

Post Thu Dec 14, 2006 10:02 pm

Brianmoooore wrote:On the other hand, Colin Chapman used to put non matching crown wheels and pinions together in diffs and add grinding paste, and he was a fairly successful engineer!
Quite a special running in period, I imagine!
Image
Speedtouch
Old Skooler
Old Skooler
Posts: 14129
Joined: Tue Feb 14, 2006 11:00 pm
Location: Canterbury

Post Thu Dec 14, 2006 10:09 pm

I had a diff go very noisy after high mileage, it turned out to be worn case-hardening on the pinion teeth.
No amount of sawdust, etc. would quieten it.
///M aurice
ECU Upgrade EPROM Chips, £40 posted within the UK. Note these are not Zone chips.
viewtopic.php?f=6&t=279421
bennyboy
E30 Zone Newbie
E30 Zone Newbie
Posts: 218
Joined: Mon Jan 10, 2005 11:00 pm
Location: West Sussex

Post Thu Dec 14, 2006 11:18 pm

just taken the diff apart and its the input shaft bearings that have gone. £70 will get me the two bearings on this shaft. Shall i take this on my self?
Image
16V IS engine!!!
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Thu Dec 14, 2006 11:21 pm

Brianmoooore wrote:E30 diffs have preloads and clearances to set up, which requires specialist equipment of the kind only specialist diff re builders are likely to have.
Not quite as simple as just replacing the seals and bearings.
stuartgallafant
E30 Zone Addict
E30 Zone Addict
Posts: 4531
Joined: Tue Mar 29, 2005 11:00 pm
Location: Costa del Croydon

Post Fri Dec 15, 2006 9:38 am

i've got all the data and tools needed for the job, so i was gonna do something like this at work.

its not gonna be easy, but i do love a challenge!!
Image
Templ8e30
E30 Zone Addict
E30 Zone Addict
Posts: 2801
Joined: Mon Jan 10, 2005 11:00 pm
Location: Ashton-under-Lyne, Lancashire

Post Fri Dec 15, 2006 12:17 pm

If you've never worked with feeler guages, peelable shims, micrometers and engineers blue to get the correct clearances and wear patterns I wouldn't bother.

It'd be cheaper and a lot less hassle to get a good second hand diff.

I have rebuilt a medium case diff before and I spent all weekend setting it up.

You'll find it very frustrating and you'll probably never be happy with the results.

Forget it.

Cheers,

Iain T
Image
2007 Mazda 6 2.0 estate
Political Correctness - A concept based on the idea that its possible to pick up a turd by the clean end !
stuartgallafant
E30 Zone Addict
E30 Zone Addict
Posts: 4531
Joined: Tue Mar 29, 2005 11:00 pm
Location: Costa del Croydon

Post Fri Dec 15, 2006 12:31 pm

its a good feeling if you get it right though!!
Image
bennyboy
E30 Zone Newbie
E30 Zone Newbie
Posts: 218
Joined: Mon Jan 10, 2005 11:00 pm
Location: West Sussex

Post Fri Dec 15, 2006 7:43 pm

yeah thanks. im just very impatient and thought bearings would be the quickest way. Thanks for pointing out how much work is needed for the job. i nearly jumped right in the deep end!
Anyway, i rang BMC(bmparts) as they have a '93 318i cab with 66k which will have the 4,27 ratio diff i want. £60+vat. I get it tuesday!!!
Thanls everyone, for saving me! :D
Image
16V IS engine!!!
stuartgallafant
E30 Zone Addict
E30 Zone Addict
Posts: 4531
Joined: Tue Mar 29, 2005 11:00 pm
Location: Costa del Croydon

Post Sat Dec 16, 2006 12:00 pm

bennyboy, what size is your original 4.27? is the small case or the medium case?
Image