The Benltey seems to only show the brake pad changing procedure for Girling callipers. On the ATE callipers, there is a dust cap and some sort of pin inside. Has this pin got some sort of hex head or do you need any special tools?
Do these pins need to be renewed when changing the pads?
The reason I'm asking is that I don't want to start changing the discs and pads over the Xmas and find out that I need some tool I don't have in my toolbox.
Thanks,
Kevin
Changing pads on ATE callipers - how do you remove pins?
Moderator: martauto
-
Richy325iTouring
- E30 Zone Addict

- Posts: 3490
- Joined: Sun Jan 09, 2005 11:00 pm
- Location: Newport SouthWales
7 mm allen key iirc

-
smithy318i
- Engaged to the E30 Zone

- Posts: 5797
- Joined: Thu Apr 28, 2005 11:00 pm
- Location: Tyne & Wear
remove the 13mm bolt from the end of the bottom pin, then rotate the whole calliper upwards using the top pin as a pivot.

-
Royalratch
- E30 Zone Addict

- Posts: 4921
- Joined: Sat Oct 21, 2006 11:00 pm
- Location: London
How common is that 7mm key? I tried to do this and found I did not have that key?
Couldn't even find it in 3 hardware stores.
Is it non-standard?
Couldn't even find it in 3 hardware stores.
Is it non-standard?
-
Dan318-is
- Married to the E30 Zone

- Posts: 8006
- Joined: Wed Jul 06, 2005 11:00 pm
- Location: Surrey/London
Got mine from halfords for about 3 quid on a 1/4 inch socket.Royalratch wrote:How common is that 7mm key? I tried to do this and found I did not have that key?
Couldn't even find it in 3 hardware stores.
Is it non-standard?
-
Royalratch
- E30 Zone Addict

- Posts: 4921
- Joined: Sat Oct 21, 2006 11:00 pm
- Location: London
Why do they make brake bolts such an odd size. Stopped me dead in my tracks trying to change the handbrake shoes.
So a No 7 hex key is an (imperial) 1/4 socket?
So a No 7 hex key is an (imperial) 1/4 socket?
-
old_skool
- E30 Zone Team Member

- Posts: 3405
- Joined: Fri Sep 01, 2006 11:00 pm
- Location: Glossersure
The 7mm allen key is available embedded into a 1/4" or 3/8" drive socket. Either that or buy an allen key set, I'm sure a 7 is in mine iirc?Why do they make brake bolts such an odd size. Stopped me dead in my tracks trying to change the handbrake shoes.
So a No 7 hex key is an (imperial) 1/4 socket?
Same goes for the steering rack mounting bolts, they are 15mm which is most odd.
I think they do this to stop people messing with them
-
kevin316i
- E30 Zone Regular

- Posts: 783
- Joined: Mon Jan 10, 2005 11:00 pm
Thanks for the feedback guys. I have a set of hex and torx keys so I should be OK then.
Regards,
Kevin
Regards,
Kevin
-
Templ8e30
- E30 Zone Addict

- Posts: 2801
- Joined: Mon Jan 10, 2005 11:00 pm
- Location: Ashton-under-Lyne, Lancashire
Pretty sure you can only do that with the girling non-vented typessmithy318i wrote:remove the 13mm bolt from the end of the bottom pin, then rotate the whole calliper upwards using the top pin as a pivot.
Cheers,
Iain T

2007 Mazda 6 2.0 estate
Political Correctness - A concept based on the idea that its possible to pick up a turd by the clean end !
