Changing pads on ATE callipers - how do you remove pins?

Need technical Q/A then you're in the right place

Moderator: martauto

User avatar
kevin316i
E30 Zone Regular
E30 Zone Regular
Posts: 783
Joined: Mon Jan 10, 2005 11:00 pm

Post Thu Dec 14, 2006 9:15 am

The Benltey seems to only show the brake pad changing procedure for Girling callipers. On the ATE callipers, there is a dust cap and some sort of pin inside. Has this pin got some sort of hex head or do you need any special tools?

Do these pins need to be renewed when changing the pads?

The reason I'm asking is that I don't want to start changing the discs and pads over the Xmas and find out that I need some tool I don't have in my toolbox.

Thanks,
Kevin
Richy325iTouring
E30 Zone Addict
E30 Zone Addict
Posts: 3490
Joined: Sun Jan 09, 2005 11:00 pm
Location: Newport SouthWales

Post Thu Dec 14, 2006 9:39 am

7 mm allen key iirc
Image
smithy318i
Engaged to the E30 Zone
Engaged to the E30 Zone
Posts: 5797
Joined: Thu Apr 28, 2005 11:00 pm
Location: Tyne & Wear

Post Thu Dec 14, 2006 1:14 pm

remove the 13mm bolt from the end of the bottom pin, then rotate the whole calliper upwards using the top pin as a pivot.
Image
User avatar
Royalratch
E30 Zone Addict
E30 Zone Addict
Posts: 4921
Joined: Sat Oct 21, 2006 11:00 pm
Location: London

Post Thu Dec 14, 2006 1:24 pm

How common is that 7mm key? I tried to do this and found I did not have that key?

Couldn't even find it in 3 hardware stores.

Is it non-standard?
Dan318-is
Married to the E30 Zone
Married to the E30 Zone
Posts: 8006
Joined: Wed Jul 06, 2005 11:00 pm
Location: Surrey/London

Post Thu Dec 14, 2006 1:26 pm

Royalratch wrote:How common is that 7mm key? I tried to do this and found I did not have that key?

Couldn't even find it in 3 hardware stores.

Is it non-standard?
Got mine from halfords for about 3 quid on a 1/4 inch socket. :?
User avatar
Royalratch
E30 Zone Addict
E30 Zone Addict
Posts: 4921
Joined: Sat Oct 21, 2006 11:00 pm
Location: London

Post Thu Dec 14, 2006 3:24 pm

Why do they make brake bolts such an odd size. Stopped me dead in my tracks trying to change the handbrake shoes.

So a No 7 hex key is an (imperial) 1/4 socket?
old_skool
E30 Zone Team Member
E30 Zone Team Member
Posts: 3405
Joined: Fri Sep 01, 2006 11:00 pm
Location: Glossersure

Post Thu Dec 14, 2006 7:15 pm

Why do they make brake bolts such an odd size. Stopped me dead in my tracks trying to change the handbrake shoes.

So a No 7 hex key is an (imperial) 1/4 socket?
The 7mm allen key is available embedded into a 1/4" or 3/8" drive socket. Either that or buy an allen key set, I'm sure a 7 is in mine iirc?

Same goes for the steering rack mounting bolts, they are 15mm which is most odd.

I think they do this to stop people messing with them :lol:
User avatar
kevin316i
E30 Zone Regular
E30 Zone Regular
Posts: 783
Joined: Mon Jan 10, 2005 11:00 pm

Post Thu Dec 14, 2006 8:36 pm

Thanks for the feedback guys. I have a set of hex and torx keys so I should be OK then.

Regards,
Kevin
Templ8e30
E30 Zone Addict
E30 Zone Addict
Posts: 2801
Joined: Mon Jan 10, 2005 11:00 pm
Location: Ashton-under-Lyne, Lancashire

Post Thu Dec 14, 2006 11:03 pm

smithy318i wrote:remove the 13mm bolt from the end of the bottom pin, then rotate the whole calliper upwards using the top pin as a pivot.
Pretty sure you can only do that with the girling non-vented types :?

Cheers,

Iain T
Image
2007 Mazda 6 2.0 estate
Political Correctness - A concept based on the idea that its possible to pick up a turd by the clean end !