M10 Throttle body sizes?

Need technical Q/A then you're in the right place

Moderator: martauto

User avatar
PigPen
E30 Zone Newbie
E30 Zone Newbie
Posts: 8
Joined: Sat Dec 09, 2006 11:00 pm

Post Sun Dec 10, 2006 11:05 am

Do all M10 engines have the same throttle body?

I've had an idea to use 4 of them to make a cheap ITB setup. I've got one from an 87 316i which has a 42-43mm throttle plate. Anyone know if the throttles in the 318i and E28 518 all the same size?
Last edited by PigPen on Sun Dec 10, 2006 1:22 pm, edited 1 time in total.
maxfield
Old Skooler
Old Skooler
Posts: 15185
Joined: Sat Nov 26, 2005 11:00 pm
Location: Mansfield

Post Sun Dec 10, 2006 12:45 pm

Didn't M10 engines have a carb :?
Image
User avatar
PigPen
E30 Zone Newbie
E30 Zone Newbie
Posts: 8
Joined: Sat Dec 09, 2006 11:00 pm

Post Sun Dec 10, 2006 1:28 pm

They did an injected 316 M10 for about 18 months (87-88 ) before switching to the M40, and I'm told the M10 318 was injection after late 1984. My friend's E28 518 also had an injected M10.
Turbo-Brown
Boost Junkie
Posts: 4705
Joined: Tue Feb 15, 2005 11:00 pm
Location: Aldershot, Hants

Post Sun Dec 10, 2006 4:58 pm

Ryan? From 205GTidrivers?
325i Twin Turbo (until 10am 01/12/07 :( )

www.air-in.co.uk free M20 exhaust and inlet flange
Gwynleym10
E30 Zone Addict
E30 Zone Addict
Posts: 3650
Joined: Sun Jan 09, 2005 11:00 pm
Location: London/Cymru

Post Sun Dec 10, 2006 5:35 pm

There was a injected (L jetronic) m10 from about 1984 -1987 it was the 318i
Image
Dual wheel carriers -------195litre Fuel Tank
London 2 Cape Town
www.Overlandinthesun.com
User avatar
PigPen
E30 Zone Newbie
E30 Zone Newbie
Posts: 8
Joined: Sat Dec 09, 2006 11:00 pm

Post Sun Dec 10, 2006 11:25 pm

Turbo-Brown wrote:Ryan? From 205GTidrivers?
Yep. :thumb:

I've looked up the part numbers on RealOEM.com and it seems the same part is common to the 316i, 318i, and E28 518i. :)
Turbo-Brown
Boost Junkie
Posts: 4705
Joined: Tue Feb 15, 2005 11:00 pm
Location: Aldershot, Hants

Post Mon Dec 11, 2006 1:56 pm

So what engine are these destined for? :D
325i Twin Turbo (until 10am 01/12/07 :( )

www.air-in.co.uk free M20 exhaust and inlet flange
User avatar
PigPen
E30 Zone Newbie
E30 Zone Newbie
Posts: 8
Joined: Sat Dec 09, 2006 11:00 pm

Post Mon Dec 11, 2006 5:03 pm

My Mi16.

The M10 throttle body is nice and compact and has very little rubbish on the outside so I can mount them close enough together. Since they are seperate instead of being made as pairs with DCOE spacing like most aftermarket throttle bodies I won't need to buy an inlet manifold either, just cut down the standard inlet an inch or two after the injector holes and weld on a plate which the BMW bodies bolt onto. That way I can keep the original fuel rail too.
Turbo-Brown
Boost Junkie
Posts: 4705
Joined: Tue Feb 15, 2005 11:00 pm
Location: Aldershot, Hants

Post Mon Dec 11, 2006 5:07 pm

Good thinking, Batman :cool:

Be interested to see how you link them all up, you thinking Jenvey style or with a bar that runs the length of the engine and connects them up?
325i Twin Turbo (until 10am 01/12/07 :( )

www.air-in.co.uk free M20 exhaust and inlet flange
User avatar
toby
E30 Zone Addict
E30 Zone Addict
Posts: 3609
Joined: Thu Aug 11, 2005 11:00 pm
Location: Kent

Post Mon Dec 11, 2006 6:02 pm

This sounds really good - pictures of all this would be great when it's done.
Good luck.
Image
User avatar
PigPen
E30 Zone Newbie
E30 Zone Newbie
Posts: 8
Joined: Sat Dec 09, 2006 11:00 pm

Post Mon Dec 11, 2006 7:07 pm

I'm thinking the simplest way would be to mount them with the throttle cable sides all facing upwards and link them all with a bar, something like this:

Image

...depending on how much bonnet clearence there is as the engine is tilted back towards the rear making the inlet side stick upwards, plus the alternator is quite close underneath the left-hand end, but that could be moved down a bit.
User avatar
toby
E30 Zone Addict
E30 Zone Addict
Posts: 3609
Joined: Thu Aug 11, 2005 11:00 pm
Location: Kent

Post Mon Dec 11, 2006 10:08 pm

Maybe you've already seen this but...
http://e30m3performance.com/installs/2. ... umpets.htm

Just an idle thought about somehow angling them downwards with a spacer or something if space is a problem.
Image
Turbo-Brown
Boost Junkie
Posts: 4705
Joined: Tue Feb 15, 2005 11:00 pm
Location: Aldershot, Hants

Post Mon Dec 11, 2006 10:24 pm

PigPen wrote:I'm thinking the simplest way would be to mount them with the throttle cable sides all facing upwards and link them all with a bar, something like this:

Image
Funnily enough I'm working on a set of TBs for a V8 at the moment and had come up with exactly the same idea for the linkage. Nice and easy to adjust for throttle to throttle balance if you make the bar that links the throttles threaded :)
325i Twin Turbo (until 10am 01/12/07 :( )

www.air-in.co.uk free M20 exhaust and inlet flange
User avatar
PigPen
E30 Zone Newbie
E30 Zone Newbie
Posts: 8
Joined: Sat Dec 09, 2006 11:00 pm

Post Mon Dec 11, 2006 11:04 pm

Turbo-Brown wrote:Nice and easy to adjust for throttle to throttle balance if you make the bar that links the throttles threaded :)
Great minds thinking alike? :)
User avatar
PigPen
E30 Zone Newbie
E30 Zone Newbie
Posts: 8
Joined: Sat Dec 09, 2006 11:00 pm

Post Tue Dec 12, 2006 12:54 pm

I've never seen curved trumpets like that before. Bit out of my budget though.
DawieM3
E30 Zone Regular
E30 Zone Regular
Posts: 320
Joined: Mon Jan 10, 2005 11:00 pm
Location: London

Post Tue Dec 12, 2006 1:06 pm

Pigpen,

They are standard on the S14 M3 lump. 46mm standard and 48mm for evo III,.

Regards,

Dave