what clutch fluid do i use?
Moderator: martauto
-
bennyboy
- E30 Zone Newbie

- Posts: 218
- Joined: Mon Jan 10, 2005 11:00 pm
- Location: West Sussex
i have had two slave cylinders go in the last few hundred miles. i have used Halfrauds brake/clutch fluid both times and i think this is what has caused them both to leak.

16V IS engine!!!
-
orangecurry
- E30 Zone Addict

- Posts: 2518
- Joined: Mon Apr 11, 2005 11:00 pm
- Location: West Sussex
doubtful - Halfords will just be buying stuff which is just at British-standard quality, so it should be up to the job.
Were the slaves new?
Were the slaves new?
-
bennyboy
- E30 Zone Newbie

- Posts: 218
- Joined: Mon Jan 10, 2005 11:00 pm
- Location: West Sussex
no but they looked pretty good on inspection. just seems a bit strange that they should both fail in such a short time (couple of weeks)! i have just bought a new one and dont want to go fcuking this one up! the last one failed last night when i was 160 miles from home and had to wait 6 hours for AA.
Both the last two went when i was using DOT 4 fluid. should i be using mineral oil?
Both the last two went when i was using DOT 4 fluid. should i be using mineral oil?

16V IS engine!!!
-
jcjdavis1
- E30 Zone Camper

- Posts: 1128
- Joined: Thu Apr 13, 2006 11:00 pm
- Location: Paisley Scotland
Hi secondhand can be more expensive than buying new as I found to my cost.I had two fuel pumps go before I bought new.

-
DRIFTBOY
- E30 Zone Addict

- Posts: 3131
- Joined: Mon May 22, 2006 11:00 pm
- Location: Kent
Any dot3 or dot4 brake fluid is ok for clutch fluid.
From what I've read in the past it might be wise to also fit a new clutch master cylinder.
Having a new slave will likely put more stress on the aold master cylinder and they often fail shortly after fitting a new slave - and vice versa.
From what I've read in the past it might be wise to also fit a new clutch master cylinder.
Having a new slave will likely put more stress on the aold master cylinder and they often fail shortly after fitting a new slave - and vice versa.
Jeremy Clarkson wrote:...but it drives the front wheels. Theee wrooong wheels!
da4x4turbo wrote:I raced a vivaro on the motorway once in a 318is.... and lost!!!
-
fuzzy
- He who sleeps with "Gingers"
- Posts: 14351
- Joined: Sat Jun 04, 2005 11:00 pm
- Location: melbourne Australia
i think it would be down to pure bad luck to have had 2 cylinders fail rather than blaming the halfords clutch fluid.if i remember correct slave cylinders are under £30 new from ECP so it isnt worth buying second hand,but hindsight is a wonderful thing 
-
jmc330i
- Engaged to the E30 Zone

- Posts: 6621
- Joined: Mon Jan 10, 2005 11:00 pm
- Location: Somerset
My 325i has been running on Halfrauds clutch fluid for the last 6 months and my Sport had the Halfrauds stuff for 2-3 years without problems.
James
'91 325i Sport
'93 318i touring 16v
'91 325i Sport
'93 318i touring 16v
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
Few driving lessons in order I think! No problem in driving a car with a permanently engaged clutch, although it helps to avoid stop/start traffic.bennyboy wrote: the last one failed last night when i was 160 miles from home and had to wait 6 hours for AA.
If you changed the slave without changing the master, that is probably the problem. Debris from the master is getting into the slave and damaging it.
-
bennyboy
- E30 Zone Newbie

- Posts: 218
- Joined: Mon Jan 10, 2005 11:00 pm
- Location: West Sussex
Thanks everyone. i rang the AA at 5 in the evening coz it was rush hour and thought that i would be on my way home in the next 60-90 mins. looking back i wish i had waited till 8-9 o'clock and driven without the clutch. but never mind.
its interesting you should comment on the master though. i changed that a few weeks before the first slave went. as you say, the old one probably broke up inside.
Any ideas on how to flush the system out before i put the new slave on?
its interesting you should comment on the master though. i changed that a few weeks before the first slave went. as you say, the old one probably broke up inside.
Any ideas on how to flush the system out before i put the new slave on?

16V IS engine!!!
