2 LITRE 731 HEADS & 323 heads
Moderator: martauto
-
exup
- Boost Junkie
- Posts: 351
- Joined: Tue Mar 08, 2005 11:00 pm
Are all 2 litre heads ( and 323i heads too ) the same?
, ie would a 1985 2litre l head be the same in ie port sizes as the later 731 heads or are they smaller and round like the 200 / ETA heads ?
cheers
, ie would a 1985 2litre l head be the same in ie port sizes as the later 731 heads or are they smaller and round like the 200 / ETA heads ?
cheers
-
pacerpete
- E30 Zone Team Member

- Posts: 18165
- Joined: Sun Jan 23, 2005 11:00 pm
- Location: Iver heath. South bucks.
All e30 320i and 323i heads are exactly the same,both use a 731 casting.
-
M-technik3
- E30 Zone Newbie

- Posts: 104
- Joined: Sun Apr 23, 2006 11:00 pm
And we in the US wish these head were more common and available here.
-
exup
- Boost Junkie
- Posts: 351
- Joined: Tue Mar 08, 2005 11:00 pm
Many thanks for info,pacerpete wrote:All e30 320i and 323i heads are exactly the same,both use a 731 casting.
i had head that the early heads &323 had smaller ports , if there all the same should help in my search for one
u can nt beat the zone 4 info
cheers
-
Templ8e30
- E30 Zone Addict

- Posts: 2801
- Joined: Mon Jan 10, 2005 11:00 pm
- Location: Ashton-under-Lyne, Lancashire
The E21 had the 200 casting like the eta's with small ports but E30's were all 731's.
Cheers,
Iain T
Cheers,
Iain T

2007 Mazda 6 2.0 estate
Political Correctness - A concept based on the idea that its possible to pick up a turd by the clean end !
-
Estoril-5
- E30 Zone Newbie

- Posts: 216
- Joined: Sun Dec 11, 2005 11:00 pm
- Location: Birmingham
whats a 731 when its at home?
-
Gunni
- E30 Zone Addict

- Posts: 2115
- Joined: Tue Jan 11, 2005 11:00 pm
- Location: Oxford
a 320i l-jet or motronic
-
maxfield
- Old Skooler

- Posts: 15185
- Joined: Sat Nov 26, 2005 11:00 pm
- Location: Mansfield
320/323 headEstoril-5 wrote:whats a 731 when its at home?
885 is 325 head

-
dazleeds
- old skool raver

- Posts: 12883
- Joined: Fri Apr 01, 2005 11:00 pm
- Location: Empire Building @
exup
havent managed to find the cam yet as my sheds like a bombsite but it is in there somewhere
found head so thats not a prob
Daz
havent managed to find the cam yet as my sheds like a bombsite but it is in there somewhere
found head so thats not a prob
Daz
www.oldskoolfantasy.co.uk
in the shit,the one to blame,yeh its all my fault ;)
in the shit,the one to blame,yeh its all my fault ;)
-
Andyboy
- Alpina Colada
- Posts: 12577
- Joined: Mon Sep 11, 2006 11:00 pm
- Location: Notts
Well, find out how much it would cost to ship one over. There are thousands of them over here and they would transform a 325e. The good thing is, the 731 head has the same chamber volume as the Eta head so you'd keep your existing compression - which on the US Etas isn't that great (9:1?).M-technik3 wrote:And we in the US wish these head were more common and available here.
-
exup
- Boost Junkie
- Posts: 351
- Joined: Tue Mar 08, 2005 11:00 pm
Thanks Ian , i see your now running a 731 head not the PORTED OUT ETA one, may i ask why , as i ve got 4 good 200 heads and was thinking of porting / drill out the cam bearing etc as u did , i thought u got 209 bhp out the ETA head on a std CAM ??Templ8e30 wrote:The E21 had the 200 casting like the eta's with small ports but E30's were all 731's.
Cheers,
Ian T
Regards F
-
Templ8e30
- E30 Zone Addict

- Posts: 2801
- Joined: Mon Jan 10, 2005 11:00 pm
- Location: Ashton-under-Lyne, Lancashire
I am indeed, the eta head had original size valves and wasn't particularly revvy, felt a bit restricted at full chat. I got a 731 head to replace it as there's less porting work needed so I could fit larger valves.exup wrote:Thanks Ian , i see your now running a 731 head not the PORTED OUT ETA one, may i ask why , as i ve got 4 good 200 heads and was thinking of porting / drill out the cam bearing etc as u did , i thought u got 209 bhp out the ETA head on a std CAM ??Templ8e30 wrote:The E21 had the 200 casting like the eta's with small ports but E30's were all 731's.
Cheers,
Ian T
Regards F
I've also fitted a 273 degree cat cam, she now revs like a 325i with a nice powerband that 'kicks' in at 3500rpm.
No dyno results as yet, megasquirt will be going on shortly to sort the fuelling out properly. She's seriously quick now
Cheers,
Iain T

2007 Mazda 6 2.0 estate
Political Correctness - A concept based on the idea that its possible to pick up a turd by the clean end !
-
exup
- Boost Junkie
- Posts: 351
- Joined: Tue Mar 08, 2005 11:00 pm
I followed your lead ,
but used a ported out a 731 head with 325 valves ,new guides etc , was going to fit a new 325 cam , its all waiting to be bolted up , over x mass , assume the 325 cam had a wide flat torque curve but did nt wake up enought ?
,
i ve already done one on a 731 heads with std 371 valves ported out/325CAM ETC etc but put it back in to mY old 525E , But ant COULD NOT CHIP IT CAUSE ITS A SWITCHABLE AUTO on a 2 row / 24 pin ECU ,
,
HOW MUCH WAS THE cat cam ?
CHEERS
,
but used a ported out a 731 head with 325 valves ,new guides etc , was going to fit a new 325 cam , its all waiting to be bolted up , over x mass , assume the 325 cam had a wide flat torque curve but did nt wake up enought ?
,
i ve already done one on a 731 heads with std 371 valves ported out/325CAM ETC etc but put it back in to mY old 525E , But ant COULD NOT CHIP IT CAUSE ITS A SWITCHABLE AUTO on a 2 row / 24 pin ECU ,
HOW MUCH WAS THE cat cam ?
CHEERS
,
-
Andyboy
- Alpina Colada
- Posts: 12577
- Joined: Mon Sep 11, 2006 11:00 pm
- Location: Notts
My old man chipped my 525e auto, a 1987E Lux with the non-switchable auto. It raised the rev limit to 5000, gave it a huge increase in fuelling and timing and transformed it. Etas are quite torquey but conversely a bit flat as well. This one went well afterwards but the cam is the limiting factor.
To be honest I don't see the point on fitting 325i valves to a 731 head. Unless you're using some ghastly US spec Eta, why not just use a 325i head? They're £50-100 in any scrapyard and have the bigger valves and slightly bigger inlet ports as standard. Despite what many 'expurts' say it doesn't adversely affect the compression ratio either.
To be honest I don't see the point on fitting 325i valves to a 731 head. Unless you're using some ghastly US spec Eta, why not just use a 325i head? They're £50-100 in any scrapyard and have the bigger valves and slightly bigger inlet ports as standard. Despite what many 'expurts' say it doesn't adversely affect the compression ratio either.
-
Templ8e30
- E30 Zone Addict

- Posts: 2801
- Joined: Mon Jan 10, 2005 11:00 pm
- Location: Ashton-under-Lyne, Lancashire
The Cat cam was about £250 from here http://www.catcams.co.uk/
Andy, I used the 731 head because the combustion chambers are correct for the Eta pistons and I'm a bit anal about doing things the 'correct' way
Cheers,
Iain T
Andy, I used the 731 head because the combustion chambers are correct for the Eta pistons and I'm a bit anal about doing things the 'correct' way
Cheers,
Iain T

2007 Mazda 6 2.0 estate
Political Correctness - A concept based on the idea that its possible to pick up a turd by the clean end !
