Alloy front arms

Need technical Q/A then you're in the right place

Moderator: martauto

old_skool
E30 Zone Team Member
E30 Zone Team Member
Posts: 3405
Joined: Fri Sep 01, 2006 11:00 pm
Location: Glossersure

Post Sat Dec 02, 2006 8:14 pm

Just dropping the front end out of the touring and noted the front arms are alloy. The lower balljoint in the n/s is shot, is it worth keeping the alloy arms and replacing/pressing new joints or is it wise to replace with new steel arms.

I'm sure I've read about alloy arms being hard to find, were they all alloy from factory?
fuzzy
He who sleeps with "Gingers"
Posts: 14351
Joined: Sat Jun 04, 2005 11:00 pm
Location: melbourne Australia

Post Sat Dec 02, 2006 8:17 pm

i think the only differences are about £300 in cash and minimal weight difference.most folk replace with steel at around £30 each.i did.
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Sat Dec 02, 2006 8:21 pm

Don't think you can change the joints on the alloy arms, so it's £300 or a couple of steel arms.
Dan318-is
Married to the E30 Zone
Married to the E30 Zone
Posts: 8006
Joined: Wed Jul 06, 2005 11:00 pm
Location: Surrey/London

Post Sat Dec 02, 2006 10:11 pm

Brianmoooore wrote:Don't think you can change the joints on the alloy arms, so it's £300 or a couple of steel arms.
Correct. Although the ball joints can physically be pressed in, they will damage the alloy arms; i think it cracks them or something? as said they are not cheap!
fuzzy
He who sleeps with "Gingers"
Posts: 14351
Joined: Sat Jun 04, 2005 11:00 pm
Location: melbourne Australia

Post Sat Dec 02, 2006 10:14 pm

£360 per pair compaired to £60 for a pair of steel ones from ECP 8O
Morat
E30 Zone Team Member
E30 Zone Team Member
Posts: 8943
Joined: Thu Feb 09, 2006 11:00 pm
Location: The Peoples Republic of Yorkshire

Post Sun Dec 03, 2006 1:31 am

So... why did BMW bother with them?
E30 Touring 0.35 cD - more slippery than prison soap :)

Image
Praise the Lard... and pass the dripping!
Dan318-is
Married to the E30 Zone
Married to the E30 Zone
Posts: 8006
Joined: Wed Jul 06, 2005 11:00 pm
Location: Surrey/London

Post Sun Dec 03, 2006 1:39 am

Morat wrote:So... why did BMW bother with them?
Principly they were installed on later m3's as being made of aluminium they are a lot less weight. If you ever get the chance to pick up a steel wishbone then an aluminium one do so and you will be amazed at the difference. Its not just the loss of mass in the actual wishbone, its the loss of unsprung mass that benefits the cars handling, braking, etc. im guessing they were included on 325 tourings to keep the weight down some more as they had beefier suspension struts (56mm instead of 51mm iirc) already.

When i fitted them to mine i noticed a massive difference!
oguz327
Captain Armco
Captain Armco
Posts: 4174
Joined: Tue Oct 25, 2005 11:00 pm
Location: Hampshire

Post Sun Dec 03, 2006 2:02 am

Dan318-is wrote:
Morat wrote:So... why did BMW bother with them?
Principly they were installed on later m3's as being made of aluminium they are a lot less weight. If you ever get the chance to pick up a steel wishbone then an aluminium one do so and you will be amazed at the difference. Its not just the loss of mass in the actual wishbone, its the loss of unsprung mass that benefits the cars handling, braking, etc. im guessing they were included on 325 tourings to keep the weight down some more as they had beefier suspension struts (56mm instead of 51mm iirc) already.

When i fitted them to mine i noticed a massive difference!
What was the massive difference dude?
Dan318-is
Married to the E30 Zone
Married to the E30 Zone
Posts: 8006
Joined: Wed Jul 06, 2005 11:00 pm
Location: Surrey/London

Post Sun Dec 03, 2006 2:06 am

Quicker steering response, a lot less harsh over bumps and a lot more stable round long sweeping corners such as goldsworth park raceway. :o