Just dropping the front end out of the touring and noted the front arms are alloy. The lower balljoint in the n/s is shot, is it worth keeping the alloy arms and replacing/pressing new joints or is it wise to replace with new steel arms.
I'm sure I've read about alloy arms being hard to find, were they all alloy from factory?
Alloy front arms
Moderator: martauto
-
old_skool
- E30 Zone Team Member

- Posts: 3405
- Joined: Fri Sep 01, 2006 11:00 pm
- Location: Glossersure
-
fuzzy
- He who sleeps with "Gingers"
- Posts: 14351
- Joined: Sat Jun 04, 2005 11:00 pm
- Location: melbourne Australia
i think the only differences are about £300 in cash and minimal weight difference.most folk replace with steel at around £30 each.i did.
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
Don't think you can change the joints on the alloy arms, so it's £300 or a couple of steel arms.
-
Dan318-is
- Married to the E30 Zone

- Posts: 8006
- Joined: Wed Jul 06, 2005 11:00 pm
- Location: Surrey/London
Correct. Although the ball joints can physically be pressed in, they will damage the alloy arms; i think it cracks them or something? as said they are not cheap!Brianmoooore wrote:Don't think you can change the joints on the alloy arms, so it's £300 or a couple of steel arms.
-
fuzzy
- He who sleeps with "Gingers"
- Posts: 14351
- Joined: Sat Jun 04, 2005 11:00 pm
- Location: melbourne Australia
£360 per pair compaired to £60 for a pair of steel ones from ECP 
-
Morat
- E30 Zone Team Member

- Posts: 8943
- Joined: Thu Feb 09, 2006 11:00 pm
- Location: The Peoples Republic of Yorkshire
So... why did BMW bother with them?
E30 Touring 0.35 cD - more slippery than prison soap 

Praise the Lard... and pass the dripping!

Praise the Lard... and pass the dripping!
-
Dan318-is
- Married to the E30 Zone

- Posts: 8006
- Joined: Wed Jul 06, 2005 11:00 pm
- Location: Surrey/London
Principly they were installed on later m3's as being made of aluminium they are a lot less weight. If you ever get the chance to pick up a steel wishbone then an aluminium one do so and you will be amazed at the difference. Its not just the loss of mass in the actual wishbone, its the loss of unsprung mass that benefits the cars handling, braking, etc. im guessing they were included on 325 tourings to keep the weight down some more as they had beefier suspension struts (56mm instead of 51mm iirc) already.Morat wrote:So... why did BMW bother with them?
When i fitted them to mine i noticed a massive difference!
-
oguz327
- Captain Armco

- Posts: 4174
- Joined: Tue Oct 25, 2005 11:00 pm
- Location: Hampshire
What was the massive difference dude?Dan318-is wrote:Principly they were installed on later m3's as being made of aluminium they are a lot less weight. If you ever get the chance to pick up a steel wishbone then an aluminium one do so and you will be amazed at the difference. Its not just the loss of mass in the actual wishbone, its the loss of unsprung mass that benefits the cars handling, braking, etc. im guessing they were included on 325 tourings to keep the weight down some more as they had beefier suspension struts (56mm instead of 51mm iirc) already.Morat wrote:So... why did BMW bother with them?
When i fitted them to mine i noticed a massive difference!
-
Dan318-is
- Married to the E30 Zone

- Posts: 8006
- Joined: Wed Jul 06, 2005 11:00 pm
- Location: Surrey/London
Quicker steering response, a lot less harsh over bumps and a lot more stable round long sweeping corners such as goldsworth park raceway. 

