btb manifold (m20)
Moderator: martauto
-
jimerilo
- E30 Zone Regular

- Posts: 285
- Joined: Mon Oct 09, 2006 11:00 pm
- Location: Yorkshire
Ive just purchased a mild steel btb manifold but ive noticed that it doesnt have a thread/hole for the lamba senser? is this right? surely my sport wont run properly if this isnt fitted?
any info will be greatly appreciated.
any info will be greatly appreciated.
-
Templ8e30
- E30 Zone Addict

- Posts: 2801
- Joined: Mon Jan 10, 2005 11:00 pm
- Location: Ashton-under-Lyne, Lancashire
I assume you'll be ditching the cat anyway if you fit this manifold (if it actually had one) ?
If so ditch the lambda sensor, the ECU will operate in open-loop mode (like all non-cat models) and you may find it runs better.
Cheers,
Iain T
If so ditch the lambda sensor, the ECU will operate in open-loop mode (like all non-cat models) and you may find it runs better.
Cheers,
Iain T

2007 Mazda 6 2.0 estate
Political Correctness - A concept based on the idea that its possible to pick up a turd by the clean end !
-
jimerilo
- E30 Zone Regular

- Posts: 285
- Joined: Mon Oct 09, 2006 11:00 pm
- Location: Yorkshire
Thankyou for the info Templ8e30
My car doesnt have a cat fitted but has a two piece exhaust system so abit of modding needed.
When you say ditch the sensor do you mean dis connect from loom at connector or just zip tie up out the way still plugged in?
cheers.
My car doesnt have a cat fitted but has a two piece exhaust system so abit of modding needed.
When you say ditch the sensor do you mean dis connect from loom at connector or just zip tie up out the way still plugged in?
cheers.
-
toughguych
- E30 Zone Newbie

- Posts: 211
- Joined: Sat Feb 19, 2005 11:00 pm
- Location: Channel Islands
jimerilo mate,
I am thinking of getting a 6 branch.
I also have a two part exhaust which I fitted 18 month ago so dont want to swap out.
I would be interseted to know how you get on fitting the 6 branch manifold to your two piece.

I am thinking of getting a 6 branch.
I also have a two part exhaust which I fitted 18 month ago so dont want to swap out.
I would be interseted to know how you get on fitting the 6 branch manifold to your two piece.
-
Templ8e30
- E30 Zone Addict

- Posts: 2801
- Joined: Mon Jan 10, 2005 11:00 pm
- Location: Ashton-under-Lyne, Lancashire
You'll need to unplug the sensor from the wiring loom.
If you find an E30 in the scrappies without a Lambda sensor there should be a dummy plug for the wiring connector, get hold of one to protect it from water and dirt.
The dummy plug has no connectors in it and you can run the car without it.
Cheers,
Iain T
If you find an E30 in the scrappies without a Lambda sensor there should be a dummy plug for the wiring connector, get hold of one to protect it from water and dirt.
The dummy plug has no connectors in it and you can run the car without it.
Cheers,
Iain T

2007 Mazda 6 2.0 estate
Political Correctness - A concept based on the idea that its possible to pick up a turd by the clean end !
-
toughguych
- E30 Zone Newbie

- Posts: 211
- Joined: Sat Feb 19, 2005 11:00 pm
- Location: Channel Islands
Surely thats just the same as tying it out the way?
Wouldnt a bit of insulating tape at the sensor end of the wire do the job?
Asking cause I need to do mine!
Wouldnt a bit of insulating tape at the sensor end of the wire do the job?
Asking cause I need to do mine!
-
jimerilo
- E30 Zone Regular

- Posts: 285
- Joined: Mon Oct 09, 2006 11:00 pm
- Location: Yorkshire
Templ8e30 thanks again for your info, much appreciated.
toughguych, will post up some pics/info on how i fitted it once complete.
toughguych, will post up some pics/info on how i fitted it once complete.
-
Templ8e30
- E30 Zone Addict

- Posts: 2801
- Joined: Mon Jan 10, 2005 11:00 pm
- Location: Ashton-under-Lyne, Lancashire
Nope, it's an oxygen sensor that gives a small voltage output corresponding to the oxygen content of the gas its sensing. If you just remove it from the exhaust but leave it connected to the wiring it'll be sensing free air instead of exhaust gas giving a false reading and the engine will run badly.toughguych wrote:Surely thats just the same as tying it out the way?
Wouldnt a bit of insulating tape at the sensor end of the wire do the job?
Asking cause I need to do mine!
Cheers,
Iain T

2007 Mazda 6 2.0 estate
Political Correctness - A concept based on the idea that its possible to pick up a turd by the clean end !
-
toughguych
- E30 Zone Newbie

- Posts: 211
- Joined: Sat Feb 19, 2005 11:00 pm
- Location: Channel Islands
Thanks for the info Iain.
-
he30
- E30 Zone Regular

- Posts: 978
- Joined: Tue Oct 31, 2006 11:00 pm
- Location: west yorkshire
Not really related fella, did you get your mates number for the wheel refurb? 
-
jimerilo
- E30 Zone Regular

- Posts: 285
- Joined: Mon Oct 09, 2006 11:00 pm
- Location: Yorkshire
Now then mate totally forgot about that sorry,
gonna see him early next week so will let you know.
gonna see him early next week so will let you know.
-
he30
- E30 Zone Regular

- Posts: 978
- Joined: Tue Oct 31, 2006 11:00 pm
- Location: west yorkshire
I'm looking at modding my engine fella, nowing you've had some work done mate, where would you say the best place to start is ? Looking for a winter project. Don't want anything that can't be reversed as my cars pretty standard, just a few little tweeks!...thoughts?
Cheers he30
Cheers he30
-
jimerilo
- E30 Zone Regular

- Posts: 285
- Joined: Mon Oct 09, 2006 11:00 pm
- Location: Yorkshire
He30 you have pm 
-
jimerilo
- E30 Zone Regular

- Posts: 285
- Joined: Mon Oct 09, 2006 11:00 pm
- Location: Yorkshire
Finally got round to fitting my manifold a few days ago and everything about the manifold is very good. My car feels soooo much more eager to rev, sounds well and feels alot quicker
For anyone out there thinking about purchasing a manifold, btb seem to be well worth the money.
james.
For anyone out there thinking about purchasing a manifold, btb seem to be well worth the money.
james.

