btb manifold (m20)

Need technical Q/A then you're in the right place

Moderator: martauto

jimerilo
E30 Zone Regular
E30 Zone Regular
Posts: 285
Joined: Mon Oct 09, 2006 11:00 pm
Location: Yorkshire

Post Fri Nov 17, 2006 8:13 pm

Ive just purchased a mild steel btb manifold but ive noticed that it doesnt have a thread/hole for the lamba senser? is this right? surely my sport wont run properly if this isnt fitted?
any info will be greatly appreciated.
Templ8e30
E30 Zone Addict
E30 Zone Addict
Posts: 2801
Joined: Mon Jan 10, 2005 11:00 pm
Location: Ashton-under-Lyne, Lancashire

Post Sat Nov 18, 2006 2:49 pm

I assume you'll be ditching the cat anyway if you fit this manifold (if it actually had one) ?

If so ditch the lambda sensor, the ECU will operate in open-loop mode (like all non-cat models) and you may find it runs better.

Cheers,

Iain T
Image
2007 Mazda 6 2.0 estate
Political Correctness - A concept based on the idea that its possible to pick up a turd by the clean end !
jimerilo
E30 Zone Regular
E30 Zone Regular
Posts: 285
Joined: Mon Oct 09, 2006 11:00 pm
Location: Yorkshire

Post Sat Nov 18, 2006 5:10 pm

Thankyou for the info Templ8e30 :thumb:
My car doesnt have a cat fitted but has a two piece exhaust system so abit of modding needed.
When you say ditch the sensor do you mean dis connect from loom at connector or just zip tie up out the way still plugged in?

cheers.
toughguych
E30 Zone Newbie
E30 Zone Newbie
Posts: 211
Joined: Sat Feb 19, 2005 11:00 pm
Location: Channel Islands

Post Sat Nov 18, 2006 7:46 pm

jimerilo mate,
I am thinking of getting a 6 branch.
I also have a two part exhaust which I fitted 18 month ago so dont want to swap out.
I would be interseted to know how you get on fitting the 6 branch manifold to your two piece.
:D
Templ8e30
E30 Zone Addict
E30 Zone Addict
Posts: 2801
Joined: Mon Jan 10, 2005 11:00 pm
Location: Ashton-under-Lyne, Lancashire

Post Sat Nov 18, 2006 8:06 pm

You'll need to unplug the sensor from the wiring loom.

If you find an E30 in the scrappies without a Lambda sensor there should be a dummy plug for the wiring connector, get hold of one to protect it from water and dirt.

The dummy plug has no connectors in it and you can run the car without it.

Cheers,

Iain T
Image
2007 Mazda 6 2.0 estate
Political Correctness - A concept based on the idea that its possible to pick up a turd by the clean end !
toughguych
E30 Zone Newbie
E30 Zone Newbie
Posts: 211
Joined: Sat Feb 19, 2005 11:00 pm
Location: Channel Islands

Post Sat Nov 18, 2006 8:15 pm

Surely thats just the same as tying it out the way?
Wouldnt a bit of insulating tape at the sensor end of the wire do the job?
Asking cause I need to do mine!
jimerilo
E30 Zone Regular
E30 Zone Regular
Posts: 285
Joined: Mon Oct 09, 2006 11:00 pm
Location: Yorkshire

Post Sat Nov 18, 2006 8:31 pm

Templ8e30 thanks again for your info, much appreciated. :)

toughguych, will post up some pics/info on how i fitted it once complete.
Templ8e30
E30 Zone Addict
E30 Zone Addict
Posts: 2801
Joined: Mon Jan 10, 2005 11:00 pm
Location: Ashton-under-Lyne, Lancashire

Post Sat Nov 18, 2006 9:44 pm

toughguych wrote:Surely thats just the same as tying it out the way?
Wouldnt a bit of insulating tape at the sensor end of the wire do the job?
Asking cause I need to do mine!
Nope, it's an oxygen sensor that gives a small voltage output corresponding to the oxygen content of the gas its sensing. If you just remove it from the exhaust but leave it connected to the wiring it'll be sensing free air instead of exhaust gas giving a false reading and the engine will run badly.

Cheers,

Iain T
Image
2007 Mazda 6 2.0 estate
Political Correctness - A concept based on the idea that its possible to pick up a turd by the clean end !
toughguych
E30 Zone Newbie
E30 Zone Newbie
Posts: 211
Joined: Sat Feb 19, 2005 11:00 pm
Location: Channel Islands

Post Sun Nov 19, 2006 7:30 pm

Thanks for the info Iain.
he30
E30 Zone Regular
E30 Zone Regular
Posts: 978
Joined: Tue Oct 31, 2006 11:00 pm
Location: west yorkshire

Post Sun Nov 19, 2006 8:51 pm

Not really related fella, did you get your mates number for the wheel refurb? :D
jimerilo
E30 Zone Regular
E30 Zone Regular
Posts: 285
Joined: Mon Oct 09, 2006 11:00 pm
Location: Yorkshire

Post Sun Nov 19, 2006 10:36 pm

Now then mate totally forgot about that sorry,
gonna see him early next week so will let you know. :)
he30
E30 Zone Regular
E30 Zone Regular
Posts: 978
Joined: Tue Oct 31, 2006 11:00 pm
Location: west yorkshire

Post Tue Nov 21, 2006 7:49 pm

I'm looking at modding my engine fella, nowing you've had some work done mate, where would you say the best place to start is ? Looking for a winter project. Don't want anything that can't be reversed as my cars pretty standard, just a few little tweeks!...thoughts?

Cheers he30
jimerilo
E30 Zone Regular
E30 Zone Regular
Posts: 285
Joined: Mon Oct 09, 2006 11:00 pm
Location: Yorkshire

Post Sat Nov 25, 2006 9:31 am

He30 you have pm :)
jimerilo
E30 Zone Regular
E30 Zone Regular
Posts: 285
Joined: Mon Oct 09, 2006 11:00 pm
Location: Yorkshire

Post Thu Nov 30, 2006 9:05 pm

Finally got round to fitting my manifold a few days ago and everything about the manifold is very good. My car feels soooo much more eager to rev, sounds well and feels alot quicker :)
For anyone out there thinking about purchasing a manifold, btb seem to be well worth the money.

james.