Taylor's Engine Refurb Pics

Show off your pride and joy here

Moderator: martauto

Taylor325i
E30 Zone Camper
E30 Zone Camper
Posts: 1120
Joined: Sun Jan 30, 2005 11:00 pm
Location: Kilmarnock, Ayrshire, Scotland. Brilliant Red Tech II 325i.

Post Sun May 14, 2006 9:09 pm

After plans to put my track car on the road were well and truly scuppered (failed MOT big time and is not worth the cost of getting the work done - needs "a bit" of welding), I took the decision of transplanting the engine into my red 325i. The reason being that the engine that I put in last year was not as quick as the original engine that was in the car and tbh I think it needed a rebuild as I suspect it had done mega miles. Plus the engine from the track car is a good, fast, strong engine with no leaks.
Me being me I had to give the engine a bit of a clean up so it was completely stripped down as far as possible without removing the head or the sump. Next the whole engine was degreased and the block was painted satin black. Various brackets were also painted aswell as the rusty bit of the alternator. All alloy parts were cleaned up and copper brushed.

All new parts fitted were:-

Timing belt and tensioner
Thermostat housing, gasket and cover
Thermostat
Blue and brown temp sensors
Water pump gasket
Inlet manifold gaskets
Throttle body gaskets
Exhaust manifold gaskets, studs and nuts
Rocker cover gasket
All possible nuts, bolts and washers replaced with stainless steel ones

Stripped and ready for paint

Image

Painted and ready for re-assembly

Image

Image

Timing belt, tensioner, belt covers and thermostat housing fitted

Image

Image

Inlet manifold and alternator fitted

Image

New manifold studs and nuts fitted

Image

All plumbed up and wired and ready for insertion winkeye

Image

Image

A couple of problems were encountered along the way

1. I snapped the middle stud while removing the inlet manifold. This was drilled out ready for re-tapping but I drilled too big a hole and had to take it up from a M8 thread to a M10. :oops: :x

2. After installing the engine and while trying to bleed the cooling system I found a leak. The hole on the thermostat housing for one of the blanking plugs had been drilled too close to the edge of the body of the housing and did not leave enough flat surface for the copper washer to seal against. :x :cry: So after about an hour and a half, several copper washers and some ptfe tape, I finally got it sealed. The moral of this story is if you're gonna fit a new thermostat housing - don't get it from GSF - buy a BMW one as they are not that much dearer as I found out when it was too late. :mad:

Apart from that pretty straight forward although time consuming.

P.S. Apologies for the long post but there have been longer, less interesting posts than this before. :giggle:



Taylor.
Image
Cloggy Saint
Old Skooler
Old Skooler
Posts: 8027
Joined: Sun Jan 09, 2005 11:00 pm
Location: zummerzet

Post Sun May 14, 2006 9:35 pm

good work mate, i'm very jealous!
Image

E30 zone - promoting adult illiteracy since 2004
gcorky
Boost Junkie
Posts: 2009
Joined: Tue Jul 12, 2005 11:00 pm
Location: n.e england

Post Sun May 14, 2006 9:51 pm

very nice m8
Image

525 sport
User avatar
rare
E30 Zone Regular
E30 Zone Regular
Posts: 590
Joined: Sun Jan 09, 2005 11:00 pm
Location: Sussex

Post Mon May 15, 2006 10:11 am

Looks real good, wish mine was that clean!
EThreezero
E30 Zone Camper
E30 Zone Camper
Posts: 1007
Joined: Mon Jun 20, 2005 11:00 pm
Location: Central Caledonia

Post Mon May 15, 2006 1:50 pm

Thought i recognised that driveway, hows it going geezer?. Shame about the MOT but its inspired you to do an engine refurb to better the life of another E30 so thats got to be a good thing :) and you have in turn inspired me to rip out my own lump (sounds a bit dodgy) and give it a right good clean and renew a few ancilliries so again a good thing. Since gettin mine back from the bump repair man ive had the beast out a couple of times and noticed some steering wrongnesses so i was going to put her off the road again for all round bush renewal etc, ive got a set of those nice purple ones, so could just do the engine thing aswell its manky and could be doing with it. Any chance i could hire that engine lift off you when your done???? winkeye anyway class post and i hope all is well.
Image

*******MERC E240 BREAKING..1998...LEATHER...ALL PARTS*******
Taylor325i
E30 Zone Camper
E30 Zone Camper
Posts: 1120
Joined: Sun Jan 30, 2005 11:00 pm
Location: Kilmarnock, Ayrshire, Scotland. Brilliant Red Tech II 325i.

Post Mon May 15, 2006 6:33 pm

Cheers for the positive comments guys. :thumb:


toitliketoiger wrote:Thought i recognised that driveway, hows it going geezer?. Shame about the MOT but its inspired you to do an engine refurb to better the life of another E30 so thats got to be a good thing :) and you have in turn inspired me to rip out my own lump (sounds a bit dodgy) and give it a right good clean and renew a few ancilliries so again a good thing. Since gettin mine back from the bump repair man ive had the beast out a couple of times and noticed some steering wrongnesses so i was going to put her off the road again for all round bush renewal etc, ive got a set of those nice purple ones, so could just do the engine thing aswell its manky and could be doing with it. Any chance i could hire that engine lift off you when your done???? winkeye anyway class post and i hope all is well.

Hi Mark, how's you?

Sorry bud but the engine lift was borrowed from a mate who runs his own garage and he'll not hire it out. I only had it on the terms that if he needed it back quick he knew I could have it delivered back within half an hour. You can hire them from HSS etc for about £20 a day though.
I think a clean engine bay would finish your car off nicely - it's mint and one of the coolest Tourers on the Zone.


Cheers!


Taylor.
Image
EThreezero
E30 Zone Camper
E30 Zone Camper
Posts: 1007
Joined: Mon Jun 20, 2005 11:00 pm
Location: Central Caledonia

Post Mon May 15, 2006 7:02 pm

I think a clean engine bay would finish your car off nicely - it's mint and one of the coolest Tourers on the Zone.



Cheers dude nice of you to say but do you mean mint niiiiice or mint flawless cause the later its not anymore :cry: needs a couple of little rust spots treated and a full respray. Its came back from the body shop and im not too happy at all with the result, the gaps are all to fcuk, the one between the wing and the bonnet is like a valley. It'll have to do for now untill i can afford a respray, whoever i get to paint it can reset the wing. Still from her good side she is still defo mint niiiiice! Cheers the noo man.
Image

*******MERC E240 BREAKING..1998...LEATHER...ALL PARTS*******
charlE30
E30 Zone Addict
E30 Zone Addict
Posts: 3818
Joined: Mon Jan 10, 2005 11:00 pm
Location: Warwick

Post Sat May 20, 2006 12:29 pm

Job well done mate :thumb: can you tell me what paints you used and how you got the manifold etc looking like new?

I'm soon to fit my 3.5 and have decided that whilst the engine is out it would be a good time to do what you have done.

Very impressed with your engine :cool:
BMW E30 344i track car :banana:
BMW F31 335d xdrive
Taylor325i
E30 Zone Camper
E30 Zone Camper
Posts: 1120
Joined: Sun Jan 30, 2005 11:00 pm
Location: Kilmarnock, Ayrshire, Scotland. Brilliant Red Tech II 325i.

Post Sun May 21, 2006 11:15 am

Thanks mate!

The block was painted with hammerite satin black and all the alloy parts were de-greased with gunk then I used a copper bristle brush to give a bit of a shine. The inlet manifold is a pig to do and takes ages but the results are worth it.
You should definately clean your 3.5 when it's out - you would regret it if you didn't. Good luck with it and keep us posted of your progress.



Taylor.
Image
charlE30
E30 Zone Addict
E30 Zone Addict
Posts: 3818
Joined: Mon Jan 10, 2005 11:00 pm
Location: Warwick

Post Sun May 21, 2006 1:04 pm

I thought I saw a can of hammerite in the first photo :D I take it then that it's suitable for high temperatures?
BMW E30 344i track car :banana:
BMW F31 335d xdrive
Taylor325i
E30 Zone Camper
E30 Zone Camper
Posts: 1120
Joined: Sun Jan 30, 2005 11:00 pm
Location: Kilmarnock, Ayrshire, Scotland. Brilliant Red Tech II 325i.

Post Sun May 21, 2006 4:52 pm

My old engine was painted with hammerite on the block and when it was removed there were no signs of the paint bubbling or peeling. I also use hammerite on brake calipers aswell with no problems.


Taylor.
Image
User avatar
stevo
E30 Zone Regular
E30 Zone Regular
Posts: 984
Joined: Sun Mar 06, 2005 11:00 pm
Location: Kilmarnock, scotland

Post Sun May 21, 2006 8:00 pm

very nice mate! 8) you must have the patience of a saint! lookin forward to seeing it on the road. i planned on cleaning the new supra engine when it was out but done a wee square and got frustrated, so set the block on fire with brake cleaner :screwy: :D
TouringMatt
E30 Zone Camper
E30 Zone Camper
Posts: 1188
Joined: Mon Jan 10, 2005 11:00 pm
Location: Not where i should be

Post Mon May 22, 2006 3:11 pm

I like :cool:

Picked up a 2.5 engine at the weekend and plan on painting it but was unsure how to go about it/what paint to use etc - well timed thread :D

Matt
E30cabrioman
E30 Zone Newbie
E30 Zone Newbie
Posts: 190
Joined: Mon Jul 18, 2005 11:00 pm
Location: Scotland

Post Mon May 22, 2006 3:31 pm

looks smart ,clean and tidy....................well worth the effort winkeye 8)
Image
325i Cab
E39 V8