M52-E30 engine mounts

Post Thu Dec 18, 2014 9:14 pm

Been trying to find somewhere to buy the 5 series cylindrical engine mounts , looked on Ebay and think I found them for about a tenner?
Do ECP have them and if so how much or is there somewhere better to buy them?
Only off work every 2 weeks so dont get much chance to check.

Post Thu Dec 18, 2014 9:44 pm

Just checked ecp on a 1986 5 series 3.4 and came back at £20, does this sound about right?

Post Sat Dec 20, 2014 12:14 pm

I've just received two from ebay for a tenner each like you said, as far as ive been told they're all the same regardless of the model so the ecp ones should be fine.

Post Sat Dec 20, 2014 2:06 pm

Stick a link up for those parts please.

Post Mon Dec 22, 2014 10:34 am

If you want uprated M5X swap engine mounts, I sell them here - http://www.hackengineering.bigcartel.co ... wap-mounts

Post Mon Dec 22, 2014 5:30 pm

HackEngineering wrote:If you want uprated M5X swap engine mounts, I sell them here - http://www.hackengineering.bigcartel.co ... wap-mounts

Would you be up for doing a group buy discount on these?

Post Mon Dec 22, 2014 5:33 pm

LondonTom wrote:
HackEngineering wrote:If you want uprated M5X swap engine mounts, I sell them here - http://www.hackengineering.bigcartel.co ... wap-mounts
Would you be up for doing a group buy discount on these?

Absolutely. How many pairs do you think we could get people signed up for? 5? 10?

Post Mon Dec 22, 2014 5:36 pm

HackEngineering wrote:
LondonTom wrote:
HackEngineering wrote:If you want uprated M5X swap engine mounts, I sell them here - http://www.hackengineering.bigcartel.co ... wap-mounts
Would you be up for doing a group buy discount on these?
Absolutely. How many pairs do you think we could get people signed up for? 5? 10?

Good man.

I would have thought 5 should be feasible.

Post Mon Dec 22, 2014 5:38 pm

LondonTom wrote:
HackEngineering wrote:
LondonTom wrote: Would you be up for doing a group buy discount on these?
Absolutely. How many pairs do you think we could get people signed up for? 5? 10?
Good man.

I would have thought 5 should be feasible.

Ok. Bring me 5 people and I will give you 10% discount. More and I will see if I can do more ;)

Post Thu Jan 08, 2015 6:57 pm

I'll take a pair please.a˜Š

Post Thu Jan 08, 2015 9:46 pm

Will start a fresh thread next week

Post Fri Jan 09, 2015 3:02 pm

Any pictures of them mounted? I cant see the angle on the website pictures

Post Mon Jan 12, 2015 10:41 am

DanThe wrote:Any pictures of them mounted? I cant see the angle on the website pictures

I don't I'm afraid - but they are promised as a direct bolt in, which will leave the gearbox exactly in line with the diff.

GB started here - guys please make sure you confirm what stiffness you would like and whether you'd like transmission mounts too, which I am offering at 10% off when purchased together.

Ben

Post Mon Jan 12, 2015 12:46 pm

Like the look of the transmission mounts on the website. Reverted back to E30 ones as I wasn't impressed by the Condor Speed Shop mounts not having the opposing ends isolated.

Post Mon Jan 12, 2015 1:47 pm

Motorhole wrote:Like the look of the transmission mounts on the website. Reverted back to E30 ones as I wasn't impressed by the Condor Speed Shop mounts not having the opposing ends isolated.

Bolt-through is certainly not the way forwards if you want it to be refined at all! Other cheap mounts we have seen are like this, much easier to make of course but very disappointing results.

Post Mon Jan 12, 2015 2:59 pm

Do you have any more information/pictures to how they are made? There are lots of mounts out there that fall apart due to poor design
Plus, if I was to be paying over £100 for a pair of mounts id like to be able to see that they are the correct shape/angle

Post Mon Jan 12, 2015 3:16 pm

DanThe wrote:Do you have any more information/pictures to how they are made? There are lots of mounts out there that fall apart due to poor design
Plus, if I was to be paying over £100 for a pair of mounts id like to be able to see that they are the correct shape/angle

They are made in the somewhat traditional manner - baseplates with studs bonded into high quality polyurethane. Others fail due to the depth of the bonding, this is not a problem with Revshift. I should also mention that these have a lifetime warranty.

I've just found a photo on the Revshift Instagram, as seen below. Let me know if this helps, happy to dig for more.

Post Mon Jan 12, 2015 7:16 pm

Looks good from that angle

Post Fri Jan 16, 2015 7:23 pm

What price are we looking at in the group buy?

Post Fri Jan 16, 2015 7:45 pm

TheMeathead wrote:What price are we looking at in the group buy?

£113 posted

Post Sun Feb 15, 2015 10:08 pm

Are we gonna get this group buy going then? I'm up for a pair.

Post Sun Feb 15, 2015 11:20 pm

There's a post in the group buy section

Post Sun Feb 15, 2015 11:26 pm

http://www.e30zone.net/modules.php?name ... c&t=258431

Post Mon Feb 16, 2015 8:26 am

Thanks Meathead, I'd never have found that.