I too have never seen how Alpina done it, not sure how much benefit you get from it though, to me it sounds like a yank thing.
Rav's Chromie, Bodywork time
Moderator: martauto
-
leeparkes
- Married to the E30 Zone
- Posts: 9538
- Joined: Thu Jan 03, 2008 11:00 pm
- Location: Black country
Either Toby or Andy335 replicated one back in the day and there was pics of the job.
I too have never seen how Alpina done it, not sure how much benefit you get from it though, to me it sounds like a yank thing.
I too have never seen how Alpina done it, not sure how much benefit you get from it though, to me it sounds like a yank thing.
Cypriotgeeza wrote:I done both my mates in my old 318is
felt so proud,even tried it with a E30 325i and got put in my place..
-
leeparkes
- Married to the E30 Zone
- Posts: 9538
- Joined: Thu Jan 03, 2008 11:00 pm
- Location: Black country
I remember years ago in films they were all raving on about there big block Hemi V8's.
I guess your a bit too old for Dukes of hazzard though, i was only a young pup.
I guess your a bit too old for Dukes of hazzard though, i was only a young pup.
Cypriotgeeza wrote:I done both my mates in my old 318is
felt so proud,even tried it with a E30 325i and got put in my place..
-
Rav335uk
- E30 Zone Meets/Events Team
- Posts: 27985
- Joined: Wed Jan 19, 2005 11:00 pm
- Location: Mad mad mad
- Contact:
After pissing around today 
and not doing much this morning, I finally decided to pull the ITB's apart and start to clean and paint them.
After a few hours
of freeing up bolts, cleaning faces and general spraying, I ended up from this:-
To this:-
The "Eagled" eyed of you will notice it's not the exact same part, but you get the idea
Only 2 more to go
and not doing much this morning, I finally decided to pull the ITB's apart and start to clean and paint them.After a few hours
of freeing up bolts, cleaning faces and general spraying, I ended up from this:-To this:-
The "Eagled" eyed of you will notice it's not the exact same part, but you get the idea
Only 2 more to go
Last edited by Rav335uk on Sat Nov 03, 2012 9:29 am, edited 1 time in total.
If you Got "Haters",Then your doing something Right!
CR24v??? Where's it all gone?? LOL
-
Rav335uk
- E30 Zone Meets/Events Team
- Posts: 27985
- Joined: Wed Jan 19, 2005 11:00 pm
- Location: Mad mad mad
- Contact:
You can run 9j all rounds with an et of 10-15.
Rears are fine, but the fronts normally need a 3mm spacer, or you can look for ET5 for the fronts.
Rears are fine, but the fronts normally need a 3mm spacer, or you can look for ET5 for the fronts.
If you Got "Haters",Then your doing something Right!
CR24v??? Where's it all gone?? LOL
-
goosiegander
- Zonegoose
- Posts: 2544
- Joined: Sun Nov 19, 2006 11:00 pm
- Location: East Anglia
Good job with the throttlebodies there dude!
-
Rav335uk
- E30 Zone Meets/Events Team
- Posts: 27985
- Joined: Wed Jan 19, 2005 11:00 pm
- Location: Mad mad mad
- Contact:
Missing out on a set of BC coilovers a few days ago 
, (Thanks Craig)
I decided to spend the money elsewhere, and bought this, atleast now I can set the car up to take the Hartge Splits.
, (Thanks Craig) I decided to spend the money elsewhere, and bought this, atleast now I can set the car up to take the Hartge Splits.
If you Got "Haters",Then your doing something Right!
CR24v??? Where's it all gone?? LOL