stolen center caps!!
Moderator: martauto
-
wangdangdo
- E30 Zone Newbie

- Posts: 4
- Joined: Mon Jan 30, 2012 11:00 pm
Hello what a great forum!! ok I just wondering if anybody knows of a way to make the centre caps on my 14" bbs wheels more secure? some little sod has nicked all 4 from my lovely 1989 325i touring Arr & I don't just want to waste money buying some from evilbay just to have them nicked again, thanks very much cheers
-
adit
- Married to the E30 Zone

- Posts: 13727
- Joined: Wed Jun 20, 2007 11:00 pm
- Location: portsmouth
Snap! i had a full set stolen from my Touring too! i don't (sorry, i mean DIDn't) remove them as it's usually the 15s that get taken. fortunately i have spares.
maybe the thieving scum lowlife mistook them for 15s, thinking he could make a few quid.
maybe the thieving scum lowlife mistook them for 15s, thinking he could make a few quid.

E30 Parts Galore!! 07901 888019
[quote="bss325i"]
Get a f* grip,we are talking about 20+yr.old sub £10k cars here,NOT the crown jewels!
-
mrLEE30
- E30 Zone Team Member

- Posts: 6589
- Joined: Tue Jan 18, 2005 11:00 pm
- Location: Sweating buckets in Bahrain
there is not a lot you can do really, i have heard some of the threaded BBS centre caps can be bolted to the wheel by tapping a small thread and putting a small bolt trough it, which of course can be removed but it helps a little.
what i do with my 16 inch BBS is i put silicone sealant on the inside if the cap and some on the end of the thread, i then use some large stiltsons to get then on (and off) its a pain to remove them with a big spanner, so much harder if someone turns up with a BBS tool, basicaly it does not stop them it just slows them down hopefully enough to put them off.
Otherwise i remove them if car parked overnight away from home.
my "tool"

what i do with my 16 inch BBS is i put silicone sealant on the inside if the cap and some on the end of the thread, i then use some large stiltsons to get then on (and off) its a pain to remove them with a big spanner, so much harder if someone turns up with a BBS tool, basicaly it does not stop them it just slows them down hopefully enough to put them off.
Otherwise i remove them if car parked overnight away from home.
my "tool"


-
scallyally
- E30 Zone Newbie

- Posts: 228
- Joined: Mon May 28, 2012 11:00 pm
- Location: east london
MrLEE30, that "tool" of your's is far too drastic for those gorgeous wheels. Far better at removing the nuts off the low-life you might find hanging round your motor. I'm looking into securing my caps as suggested above, (6x10mm c/s cap screws)
-
andyp
- True Old Skooler
- Posts: 6899
- Joined: Sun Jan 09, 2005 11:00 pm
- Location: LONDON
they will be gutted when they find out they are only 14" ones
i used clear silicone on the back of mine it makes it a lot harder to come off, thats about all you can do
i used clear silicone on the back of mine it makes it a lot harder to come off, thats about all you can do
-
G-Bear
- E30 Zone Squatter

- Posts: 1631
- Joined: Wed Mar 12, 2008 11:00 pm
- Location: Hertfordshire
Silicone is what I have been thinking of too. I never had the caps on my previous e30. But now i check for missing centres every time now on my new one.. It's a Touring too.. Best go out and check..!
