Seized brake nipples
Moderator: martauto
-
Farbbm
- E30 Zone Newbie

- Posts: 216
- Joined: Sun Feb 24, 2008 11:00 pm
- Location: bedfordshire
I dropped my car off to have an MOT and brake fluid change this morning, but i've just received a call from the garage to say that one of the brake nipples has broken off and at least two for the others have seized. The garage have advised changing the calipers but that sounds expensive. Any one have any advice or expierence of the this sort of problem?
-
macas
- E30 Zone Squatter

- Posts: 1696
- Joined: Sat Mar 10, 2007 11:00 pm
- Location: BEAUTIFUL BIRMINGHAM
Yep...just get secondhand calipers...
-
bimanut
- E30 Zone Camper

- Posts: 1194
- Joined: Thu Oct 30, 2008 11:00 pm
- Location: Warrington
siezed nipples should come undone with a little heat.As for the one with a snapped nipple for the all the hassle of trying to get it out i`d just buy a second hand unit some one on here should be able to see you right 

-
Motorhole
- E30 Zone Addict

- Posts: 2395
- Joined: Tue Jul 12, 2005 11:00 pm
- Location: Cheshire
You can buy brake nipples on their own, provided you know the sizes - I don't know the E30 ones off hand but I'm sure someone here does. Havn't had a problem removing snapped nipples before, using the hammer & torx bit solution, but I guess there's always a first!
-
scjimbo
- E30 Zone Camper

- Posts: 1249
- Joined: Thu Feb 09, 2012 11:00 pm
- Location: Gloucester
flippin heck the poor old torx bits again. I bet you have shares in themMotorhole wrote:You can buy brake nipples on their own, provided you know the sizes - I don't know the E30 ones off hand but I'm sure someone here does. Havn't had a problem removing snapped nipples before, using the hammer & torx bit solution, but I guess there's always a first!
-
Topblag
- Old Skooler

- Posts: 7095
- Joined: Wed Jul 30, 2008 11:00 pm
- Location: Fife - You got a problem with that ?
It's always a good idea to check your nipples each time you have the wheels off. Never seen an E30 brake nipple which won't come out. Seen a load of fuds rounding them off.
1990 325i Cab auto in Alpine White II
1988 Alpina C2.5 moredoor in Black, 71k
1990 325ix, moredoor auto in Laser Blue. 51k
1984 Hartge H35 in Black
2004 996 C4S in Silver 43k manual
2006 Audi S6 V10 in Black 58k
1988 Alpina C2.5 moredoor in Black, 71k
1990 325ix, moredoor auto in Laser Blue. 51k
1984 Hartge H35 in Black
2004 996 C4S in Silver 43k manual
2006 Audi S6 V10 in Black 58k
-
Motorhole
- E30 Zone Addict

- Posts: 2395
- Joined: Tue Jul 12, 2005 11:00 pm
- Location: Cheshire
My torx bits are 'ard mate 
-
scjimbo
- E30 Zone Camper

- Posts: 1249
- Joined: Thu Feb 09, 2012 11:00 pm
- Location: Gloucester
I check mine every time the misses is outTopblag wrote:It's always a good idea to check your nipples each time you have the wheels off. Never seen an E30 brake nipple which won't come out. Seen a load of fuds rounding them off.
-
Speedtouch
- Old Skooler

- Posts: 14129
- Joined: Tue Feb 14, 2006 11:00 pm
- Location: Canterbury
You can try using an Easy-out (reverse thread) extractor.
///M aurice
ECU Upgrade EPROM Chips, £40 posted within the UK. Note these are not Zone chips.
viewtopic.php?f=6&t=279421
ECU Upgrade EPROM Chips, £40 posted within the UK. Note these are not Zone chips.
viewtopic.php?f=6&t=279421
-
capri_rob
- Married to the E30 Zone

- Posts: 9678
- Joined: Tue Feb 19, 2008 11:00 pm
- Location: South Staffordshire
Theyre stupid money from BMW ( about £5 each IIRC
)
For the one thats bust off agreed get secondhand calipers
I had to replace the rears on the bronze turd for that very reason
For the one thats bust off agreed get secondhand calipers
I had to replace the rears on the bronze turd for that very reason

e30topless said : Proper BMW's have 4 headlights, last of the run was the E30 and E34/E32 anything after that is just complete shite
-
DanThe
- E30 Zone Team Member

- Posts: 28649
- Joined: Sat Sep 10, 2005 11:00 pm
- Location: Staffs
If they are seized/tight the best way to do it is take the caliper off and get it in the vice for some gas axe action. Refitting the bleed nipples with grease will stop it happening again. Most mechanics dont have a clue and think excessive force is the only way to remove things, then when it breaks, swear and buy a new one
The thread is M7, cant remember the pitch but its standard, not fine
The thread is M7, cant remember the pitch but its standard, not fine
-
Farbbm
- E30 Zone Newbie

- Posts: 216
- Joined: Sun Feb 24, 2008 11:00 pm
- Location: bedfordshire
Care to expand on the hammer & torx solution? I've got an idea what your on about but thought I ask the obvious.Motorhole wrote:You can buy brake nipples on their own, provided you know the sizes - I don't know the E30 ones off hand but I'm sure someone here does. Havn't had a problem removing snapped nipples before, using the hammer & torx bit solution, but I guess there's always a first!
-
Motorhole
- E30 Zone Addict

- Posts: 2395
- Joined: Tue Jul 12, 2005 11:00 pm
- Location: Cheshire
Brake nipples are soft, torx bits are 'ard...well, decent quality ones are. Find a bit that won't quite fit inside what's left of the brake nipple and tap it in with a hammer so its a tight fit, biting into the soft metal. Don't hit so hard as to damage the thread. Get a ratchet on the bit then wind out the remains of the nipple.
-
HairyScreech
- Engaged to the E30 Zone

- Posts: 6265
- Joined: Sun Jan 21, 2007 11:00 pm
And often the act of tapping it in there will free off the thread as well, its a bit of a hack method however it works, and sometimes that's just what you need.
2.8 development thread http://www.e30zone.net/modules.php?name ... c&t=170822
m3.3.1 m20 thread - now running, chip needed - any volunteers?
http://www.e30zone.net/modules.php?name ... =viewtopic&
m3.3.1 m20 thread - now running, chip needed - any volunteers?
http://www.e30zone.net/modules.php?name ... =viewtopic&
-
Farbbm
- E30 Zone Newbie

- Posts: 216
- Joined: Sun Feb 24, 2008 11:00 pm
- Location: bedfordshire
Excellent, I thought that was the method used.
