M52 Donor Car

General E30 related discussions -
Please put technical questions in E30 Tech Help forum below

Moderator: martauto

Motorhole
E30 Zone Addict
E30 Zone Addict
Posts: 2395
Joined: Tue Jul 12, 2005 11:00 pm
Location: Cheshire

Post Wed Jul 18, 2012 5:29 pm

Going to check out a potential donor car (e36 328i SE) for engine, gearbox, prop etc tonight. 1997 car, fairly high mileage but cheap enough. Anything in particular I should be on the lookout for? Cheers!
magpie
Old Skooler
Old Skooler
Posts: 28035
Joined: Sun Jun 29, 2008 11:00 pm
Location: Consett,Durham.

Post Wed Jul 18, 2012 5:44 pm

alusil block.

not sure what year they stopped the other type nickasil or something or other
Image
m52 b30 stroker 6-speed 318is Galvanizer
m42 touring
+ a yard full of scrap turds :)
Grrrmachine
E30 Zone Wiki / Team Member
E30 Zone Wiki / Team Member
Posts: 8043
Joined: Sat Feb 09, 2008 11:00 pm
Location: Warsaw, Poland

Post Wed Jul 18, 2012 5:58 pm

Make a cup of tea, get comfortable, and read this:

http://www.e30zone.net/e30zonewiki/index.php/M5x
daimlerman
**BANNED**
Posts: 15968
Joined: Mon Feb 27, 2006 11:00 pm
Location: Grumpy Old Man

Post Wed Jul 18, 2012 6:03 pm

Depends on your objectives,really.

Once these plastic engines have over-heated,the block is goosed,but the crank,rods and pistons will fit an iron block M50 :D
The head will skim up,but dump the M52 ECU and go with the earlier M50 item that can be mapped in the same way as an M20 ECU.

When my M50'd touring needs an engine re-build,that's my chosen route.
Youth is wasted on the young.
Barx325i
Engaged to the E30 Zone
Engaged to the E30 Zone
Posts: 6493
Joined: Wed Jul 26, 2006 11:00 pm

Post Wed Jul 18, 2012 6:14 pm

sounds like I should empty the trailer :)
E30BeemerLad
Married to the E30 Zone
Married to the E30 Zone
Posts: 16806
Joined: Mon Mar 28, 2005 11:00 pm
Location: Norfolk

Post Wed Jul 18, 2012 6:17 pm

Malcolm, I don't know why you have such a fondness for retaining the M50 ECU when sticking the 2.8 guts in a M50, the Siemens ECU on the M52 is a far superior bit of kit
daimlerman
**BANNED**
Posts: 15968
Joined: Mon Feb 27, 2006 11:00 pm
Location: Grumpy Old Man

Post Wed Jul 18, 2012 6:28 pm

E30BeemerLad wrote:Malcolm, I don't know why you have such a fondness for retaining the M50 ECU when sticking the 2.8 guts in a M50, the Siemens ECU on the M52 is a far superior bit of kit
It may well be,but you try getting some-one to re-map it!
E30BeemerLad
Married to the E30 Zone
Married to the E30 Zone
Posts: 16806
Joined: Mon Mar 28, 2005 11:00 pm
Location: Norfolk

Post Wed Jul 18, 2012 7:03 pm

No need to though, they adjust very well to changes and you're just replicating a M52 anyway :)
DanThe
E30 Zone Team Member
E30 Zone Team Member
Posts: 28649
Joined: Sat Sep 10, 2005 11:00 pm
Location: Staffs

Post Wed Jul 18, 2012 7:04 pm

daimlerman wrote:
E30BeemerLad wrote:Malcolm, I don't know why you have such a fondness for retaining the M50 ECU when sticking the 2.8 guts in a M50, the Siemens ECU on the M52 is a far superior bit of kit
It may well be,but you try getting some-one to re-map it!
Its not much different to remapping a Bosch M50 ECU, I think the point your raising is more to do with the fact an M52 ECU is not a simple chip swap job which most "tuners" favour. Remapping is a word used very loosely

With the M52B28 ECU and your m50 iron block M52B28 engine there are no issues anyway, plug and play.
daimlerman
**BANNED**
Posts: 15968
Joined: Mon Feb 27, 2006 11:00 pm
Location: Grumpy Old Man

Post Wed Jul 18, 2012 7:28 pm

E30BeemerLad wrote:No need to though, they adjust very well to changes and you're just replicating a M52 anyway :)
Not quite true young man!

M52 with M50 inlet,and a suitable ECU mod will make rather more than your stock M52....whichever block is used...
Motorhole
E30 Zone Addict
E30 Zone Addict
Posts: 2395
Joined: Tue Jul 12, 2005 11:00 pm
Location: Cheshire

Post Wed Jul 18, 2012 7:43 pm

Thanks chaps! it looks good, no water in oil or vice versa, no fluid leaks, no rattle from the chain/tensioner or vanos, revs well and pulls well, changes gear just fine. Temp sat just under halfway throughout. Will take a day or 2 to consider.
DanThe
E30 Zone Team Member
E30 Zone Team Member
Posts: 28649
Joined: Sat Sep 10, 2005 11:00 pm
Location: Staffs

Post Wed Jul 18, 2012 9:52 pm

daimlerman wrote:
E30BeemerLad wrote:No need to though, they adjust very well to changes and you're just replicating a M52 anyway :)
Not quite true young man!

M52 with M50 inlet,and a suitable ECU mod will make rather more than your stock M52....whichever block is used...
Lee knows this, he has exactly what you typed above in his car winkeye
Andyboy
Alpina Colada
Posts: 12577
Joined: Mon Sep 11, 2006 11:00 pm
Location: Notts

Post Thu Jul 19, 2012 7:36 am

Daimlerman typed that in Lee's car?
DanThe
E30 Zone Team Member
E30 Zone Team Member
Posts: 28649
Joined: Sat Sep 10, 2005 11:00 pm
Location: Staffs

Post Thu Jul 19, 2012 8:26 am

Blackberry innit
Morat
E30 Zone Team Member
E30 Zone Team Member
Posts: 8943
Joined: Thu Feb 09, 2006 11:00 pm
Location: The Peoples Republic of Yorkshire

Post Thu Jul 19, 2012 9:52 am

DanThe wrote:Blackberry innit
Where's the riot? I'm almost out of Basmati...
E30 Touring 0.35 cD - more slippery than prison soap :)

Image
Praise the Lard... and pass the dripping!