M52 Donor Car
Moderator: martauto
-
Motorhole
- E30 Zone Addict

- Posts: 2395
- Joined: Tue Jul 12, 2005 11:00 pm
- Location: Cheshire
Going to check out a potential donor car (e36 328i SE) for engine, gearbox, prop etc tonight. 1997 car, fairly high mileage but cheap enough. Anything in particular I should be on the lookout for? Cheers!
-
magpie
- Old Skooler

- Posts: 28035
- Joined: Sun Jun 29, 2008 11:00 pm
- Location: Consett,Durham.
alusil block.
not sure what year they stopped the other type nickasil or something or other
not sure what year they stopped the other type nickasil or something or other

m52 b30 stroker 6-speed 318is Galvanizer
m42 touring
+ a yard full of scrap turds
-
Grrrmachine
- E30 Zone Wiki / Team Member

- Posts: 8043
- Joined: Sat Feb 09, 2008 11:00 pm
- Location: Warsaw, Poland
'89 325i Touring | Touring Resto Thread | In-Dash Screen install
-
daimlerman
- **BANNED**
- Posts: 15968
- Joined: Mon Feb 27, 2006 11:00 pm
- Location: Grumpy Old Man
Depends on your objectives,really.
Once these plastic engines have over-heated,the block is goosed,but the crank,rods and pistons will fit an iron block M50
The head will skim up,but dump the M52 ECU and go with the earlier M50 item that can be mapped in the same way as an M20 ECU.
When my M50'd touring needs an engine re-build,that's my chosen route.
Once these plastic engines have over-heated,the block is goosed,but the crank,rods and pistons will fit an iron block M50
The head will skim up,but dump the M52 ECU and go with the earlier M50 item that can be mapped in the same way as an M20 ECU.
When my M50'd touring needs an engine re-build,that's my chosen route.
Youth is wasted on the young.
-
Barx325i
- Engaged to the E30 Zone

- Posts: 6493
- Joined: Wed Jul 26, 2006 11:00 pm
sounds like I should empty the trailer 
-
E30BeemerLad
- Married to the E30 Zone

- Posts: 16806
- Joined: Mon Mar 28, 2005 11:00 pm
- Location: Norfolk
Malcolm, I don't know why you have such a fondness for retaining the M50 ECU when sticking the 2.8 guts in a M50, the Siemens ECU on the M52 is a far superior bit of kit
-
daimlerman
- **BANNED**
- Posts: 15968
- Joined: Mon Feb 27, 2006 11:00 pm
- Location: Grumpy Old Man
It may well be,but you try getting some-one to re-map it!E30BeemerLad wrote:Malcolm, I don't know why you have such a fondness for retaining the M50 ECU when sticking the 2.8 guts in a M50, the Siemens ECU on the M52 is a far superior bit of kit
-
E30BeemerLad
- Married to the E30 Zone

- Posts: 16806
- Joined: Mon Mar 28, 2005 11:00 pm
- Location: Norfolk
No need to though, they adjust very well to changes and you're just replicating a M52 anyway 
-
DanThe
- E30 Zone Team Member

- Posts: 28649
- Joined: Sat Sep 10, 2005 11:00 pm
- Location: Staffs
Its not much different to remapping a Bosch M50 ECU, I think the point your raising is more to do with the fact an M52 ECU is not a simple chip swap job which most "tuners" favour. Remapping is a word used very looselydaimlerman wrote:It may well be,but you try getting some-one to re-map it!E30BeemerLad wrote:Malcolm, I don't know why you have such a fondness for retaining the M50 ECU when sticking the 2.8 guts in a M50, the Siemens ECU on the M52 is a far superior bit of kit
With the M52B28 ECU and your m50 iron block M52B28 engine there are no issues anyway, plug and play.
-
daimlerman
- **BANNED**
- Posts: 15968
- Joined: Mon Feb 27, 2006 11:00 pm
- Location: Grumpy Old Man
Not quite true young man!E30BeemerLad wrote:No need to though, they adjust very well to changes and you're just replicating a M52 anyway
M52 with M50 inlet,and a suitable ECU mod will make rather more than your stock M52....whichever block is used...
-
Motorhole
- E30 Zone Addict

- Posts: 2395
- Joined: Tue Jul 12, 2005 11:00 pm
- Location: Cheshire
Thanks chaps! it looks good, no water in oil or vice versa, no fluid leaks, no rattle from the chain/tensioner or vanos, revs well and pulls well, changes gear just fine. Temp sat just under halfway throughout. Will take a day or 2 to consider.
-
DanThe
- E30 Zone Team Member

- Posts: 28649
- Joined: Sat Sep 10, 2005 11:00 pm
- Location: Staffs
Lee knows this, he has exactly what you typed above in his cardaimlerman wrote:Not quite true young man!E30BeemerLad wrote:No need to though, they adjust very well to changes and you're just replicating a M52 anyway
M52 with M50 inlet,and a suitable ECU mod will make rather more than your stock M52....whichever block is used...
-
Andyboy
- Alpina Colada
- Posts: 12577
- Joined: Mon Sep 11, 2006 11:00 pm
- Location: Notts
Daimlerman typed that in Lee's car?
-
DanThe
- E30 Zone Team Member

- Posts: 28649
- Joined: Sat Sep 10, 2005 11:00 pm
- Location: Staffs
Blackberry innit
-
Morat
- E30 Zone Team Member

- Posts: 8943
- Joined: Thu Feb 09, 2006 11:00 pm
- Location: The Peoples Republic of Yorkshire
Where's the riot? I'm almost out of Basmati...DanThe wrote:Blackberry innit
E30 Touring 0.35 cD - more slippery than prison soap 

Praise the Lard... and pass the dripping!

Praise the Lard... and pass the dripping!
