idle
Moderator: martauto
-
gingerrusta
- E30 Zone Regular

- Posts: 527
- Joined: Fri Jul 31, 2009 11:00 pm
- Location: Bedfordshire
Hi
Today on my 320i 1988 Auto convertabile i changed the dizzy and dizzy cap as they both looked a bit worse for wear. The car has been idling all over the place. It seems to be a bit better when warm but does cut out alot when say you engaged reverse to move car.
Any of you gurus could give me some pointers on what to take off clean up and that kind of thing so i can get this beauty running like she should be please?
The dizzy and dizzy cap were bremi as i thought i didnt want any cheap shite on it.
Today on my 320i 1988 Auto convertabile i changed the dizzy and dizzy cap as they both looked a bit worse for wear. The car has been idling all over the place. It seems to be a bit better when warm but does cut out alot when say you engaged reverse to move car.
Any of you gurus could give me some pointers on what to take off clean up and that kind of thing so i can get this beauty running like she should be please?
The dizzy and dizzy cap were bremi as i thought i didnt want any cheap shite on it.
-
Grrrmachine
- E30 Zone Wiki / Team Member

- Posts: 8043
- Joined: Sat Feb 09, 2008 11:00 pm
- Location: Warsaw, Poland
'89 325i Touring | Touring Resto Thread | In-Dash Screen install
-
lamby
- E30 Zone Regular

- Posts: 251
- Joined: Wed Jan 27, 2010 11:00 pm
check the ecu,i.e take it apart and clean it with wd40 and a toothbrush.if the roof leaked it will run down into it and cause this.same thing on mine and i done everything else first,pipes plugs valves fpr the lot!10 mins on the ecu and runs smooth no hesitation etc if you can,t see anything obvious like loose pipework then do this first,mine cut out when in reverse and at braking,even if the roof don,t leak now it will have done at some point!
-
gingerrusta
- E30 Zone Regular

- Posts: 527
- Joined: Fri Jul 31, 2009 11:00 pm
- Location: Bedfordshire
cheers i will give this ago as it will save alot of work. is it best to disconnect the battery when doing it first ?
-
Speedtouch
- Old Skooler

- Posts: 14129
- Joined: Tue Feb 14, 2006 11:00 pm
- Location: Canterbury
Yes, disconnect it for an hour or so to reset it, reconnect then let it idle for at least 10 minutes to enable base idle settings to be learnt, switch off, then take it for a drive throughout the rev range.
Check the ECU code; if it's a later 380/381 ECU, these are notorious for blowing diodes in the idle control circuit.
Check the ECU code; if it's a later 380/381 ECU, these are notorious for blowing diodes in the idle control circuit.
///M aurice
ECU Upgrade EPROM Chips, £40 posted within the UK. Note these are not Zone chips.
viewtopic.php?f=6&t=279421
ECU Upgrade EPROM Chips, £40 posted within the UK. Note these are not Zone chips.
viewtopic.php?f=6&t=279421
-
gingerrusta
- E30 Zone Regular

- Posts: 527
- Joined: Fri Jul 31, 2009 11:00 pm
- Location: Bedfordshire
lamby wrote:check the ecu,i.e take it apart and clean it with wd40 and a toothbrush.if the roof leaked it will run down into it and cause this.same thing on mine and i done everything else first,pipes plugs valves fpr the lot!10 mins on the ecu and runs smooth no hesitation etc if you can,t see anything obvious like loose pipework then do this first,mine cut out when in reverse and at braking,even if the roof don,t leak now it will have done at some point!
i have taken Ecu out and sprayed WD40 on the pins and brushed them with a toothbrush. Do i need to actually open up the ECU or is this enough ?
-
Speedtouch
- Old Skooler

- Posts: 14129
- Joined: Tue Feb 14, 2006 11:00 pm
- Location: Canterbury
It will probably suffice. The innards of ECUs rarely go wrong unless water gets in from a leaking windscreen seal.
Which ECU number is it, e.g., 0 261 200 172.?
Which ECU number is it, e.g., 0 261 200 172.?
///M aurice
ECU Upgrade EPROM Chips, £40 posted within the UK. Note these are not Zone chips.
viewtopic.php?f=6&t=279421
ECU Upgrade EPROM Chips, £40 posted within the UK. Note these are not Zone chips.
viewtopic.php?f=6&t=279421
-
gingerrusta
- E30 Zone Regular

- Posts: 527
- Joined: Fri Jul 31, 2009 11:00 pm
- Location: Bedfordshire
its a bosch 0 261 200 163Speedtouch wrote:It will probably suffice. The innards of ECUs rarely go wrong unless water gets in from a leaking windscreen seal.
Which ECU number is it, e.g., 0 261 200 172.?
i plugged it back in tonight and run it for 10 or so mins on tick over and in fairness it seemed to run alot better. car is currently sorn off road so cant do the next bit like taking it for a nice drive to set it up properly.
but so far so good. its running a million times better at the moment
-
Speedtouch
- Old Skooler

- Posts: 14129
- Joined: Tue Feb 14, 2006 11:00 pm
- Location: Canterbury
That will be a first-generation Motronic 1.3 with the twin-PCB (printed circuit board) design. If you can get hold of one, a later single PCB 172 ECU is more reliable, and easier to chip. 
///M aurice
ECU Upgrade EPROM Chips, £40 posted within the UK. Note these are not Zone chips.
viewtopic.php?f=6&t=279421
ECU Upgrade EPROM Chips, £40 posted within the UK. Note these are not Zone chips.
viewtopic.php?f=6&t=279421
-
gingerrusta
- E30 Zone Regular

- Posts: 527
- Joined: Fri Jul 31, 2009 11:00 pm
- Location: Bedfordshire
is that the code it ends in 172 instead of 163?
-
Speedtouch
- Old Skooler

- Posts: 14129
- Joined: Tue Feb 14, 2006 11:00 pm
- Location: Canterbury
Yes, 0 261 200 172 is the later 320i ECU.
Though, you can use any of the later six-pot ECUs (172/173/179/380/381) as they are all identical, apart from the EPROM chip - just change the chip to suit.
However, note that a 163 ECU chip will not work in a later ECU, and vice-versa.
Though, you can use any of the later six-pot ECUs (172/173/179/380/381) as they are all identical, apart from the EPROM chip - just change the chip to suit.
However, note that a 163 ECU chip will not work in a later ECU, and vice-versa.
///M aurice
ECU Upgrade EPROM Chips, £40 posted within the UK. Note these are not Zone chips.
viewtopic.php?f=6&t=279421
ECU Upgrade EPROM Chips, £40 posted within the UK. Note these are not Zone chips.
viewtopic.php?f=6&t=279421
-
gingerrusta
- E30 Zone Regular

- Posts: 527
- Joined: Fri Jul 31, 2009 11:00 pm
- Location: Bedfordshire
what benefits would i see if i changed it for one of 172 ?
-
Speedtouch
- Old Skooler

- Posts: 14129
- Joined: Tue Feb 14, 2006 11:00 pm
- Location: Canterbury
They're both Motronic 1.3, so no greatly noticeable gains apart from better reliability and the far easier availability of upgrade chips, which if you get a decent one
will enhance driveability, performance and improve fuel economy.
Last edited by Speedtouch on Fri Jul 06, 2012 11:41 am, edited 1 time in total.
///M aurice
ECU Upgrade EPROM Chips, £40 posted within the UK. Note these are not Zone chips.
viewtopic.php?f=6&t=279421
ECU Upgrade EPROM Chips, £40 posted within the UK. Note these are not Zone chips.
viewtopic.php?f=6&t=279421
-
lamby
- E30 Zone Regular

- Posts: 251
- Joined: Wed Jan 27, 2010 11:00 pm
mine was the 163 which i changed for the 172 which made it run perfect,but after i stripped the 163 down,yes open it up you will have two pcb,s inside.cleaned it with wd40 and a toothbrush i put it back and it was sorted.HOWEVER i would strongly suggest you get a 172 before you clean the old one as they are cheap enough and if you bugger up the 163 it won,t matter,plus you can chip the 172 and yes it does make a nice difference on the auto.but def get a 172 and plug it in and see what happens
-
Grrrmachine
- E30 Zone Wiki / Team Member

- Posts: 8043
- Joined: Sat Feb 09, 2008 11:00 pm
- Location: Warsaw, Poland
Not only do I have a 172 ECU kicking around, I've also got one of Speedtouch's Mild chips to go with it...
'89 325i Touring | Touring Resto Thread | In-Dash Screen install
-
gingerrusta
- E30 Zone Regular

- Posts: 527
- Joined: Fri Jul 31, 2009 11:00 pm
- Location: Bedfordshire
pm cost please
-
gingerrusta
- E30 Zone Regular

- Posts: 527
- Joined: Fri Jul 31, 2009 11:00 pm
- Location: Bedfordshire
update:
Rotor arm and dizzy replaced with brand new Bremi parts.
Ecu disconnected , cleaned with WD 40 with toothbrush
reconnected and ran car for 10 mins on tick over
Took car for run to mot centre and run through rev ranges
Failed on emissions running to rich
Got car home , disconnected ICV cleaned and reconnected
disconnected MAF cleaned and reconnected
disconnected the sensor under throttle body ( cant remember the name for this bit lol ) cleaned and reconnected
started car up and is running a little better but still doesnt sound 100%.
Any ideas???
Rotor arm and dizzy replaced with brand new Bremi parts.
Ecu disconnected , cleaned with WD 40 with toothbrush
reconnected and ran car for 10 mins on tick over
Took car for run to mot centre and run through rev ranges
Failed on emissions running to rich
Got car home , disconnected ICV cleaned and reconnected
disconnected MAF cleaned and reconnected
disconnected the sensor under throttle body ( cant remember the name for this bit lol ) cleaned and reconnected
started car up and is running a little better but still doesnt sound 100%.
Any ideas???
-
Speedtouch
- Old Skooler

- Posts: 14129
- Joined: Tue Feb 14, 2006 11:00 pm
- Location: Canterbury
Check blue temperature sensor - should be around 3300 ohms cold, dropping to around 600 ohms hot.
Check air filter - replace if dirty.
Check exhaust CO emissions and adjust AFM if necessary.
Spray WD40 or similar around the inlet manifold gasket with the engine idling, and if it temporarily alters the idle speed then you have an air leak and need to either tighten the inlet manifold bolts or replace the gasket.
Check air filter - replace if dirty.
Check exhaust CO emissions and adjust AFM if necessary.
Spray WD40 or similar around the inlet manifold gasket with the engine idling, and if it temporarily alters the idle speed then you have an air leak and need to either tighten the inlet manifold bolts or replace the gasket.
///M aurice
ECU Upgrade EPROM Chips, £40 posted within the UK. Note these are not Zone chips.
viewtopic.php?f=6&t=279421
ECU Upgrade EPROM Chips, £40 posted within the UK. Note these are not Zone chips.
viewtopic.php?f=6&t=279421
-
gingerrusta
- E30 Zone Regular

- Posts: 527
- Joined: Fri Jul 31, 2009 11:00 pm
- Location: Bedfordshire
how do i check the blue temp sensor? also whereabouts is it?
Air filter is clean
how do you adjust the air flow meter???
Air filter is clean
how do you adjust the air flow meter???
-
BenHar
- E30 Zone Addict

- Posts: 3089
- Joined: Sun Jul 11, 2010 11:00 pm
- Location: Reigate, Surrey
http://www.e30zone.net/e30zonewiki/inde ... oubleshootgingerrusta wrote:how do i check the blue temp sensor? also whereabouts is it?
Air filter is clean
how do you adjust the air flow meter???
Ben
-
gingerrusta
- E30 Zone Regular

- Posts: 527
- Joined: Fri Jul 31, 2009 11:00 pm
- Location: Bedfordshire
Blue temp sensor does anyone know the part number for it please?
-
Grrrmachine
- E30 Zone Wiki / Team Member

- Posts: 8043
- Joined: Sat Feb 09, 2008 11:00 pm
- Location: Warsaw, Poland
Blue Temp Sensor info is here:
http://www.e30zone.net/e30zonewiki/index.php/Blue_Plug
You can use RealOEM to find the part number for things like this. The Blue Plug is part number 13621709966
http://www.e30zone.net/e30zonewiki/index.php/Blue_Plug
You can use RealOEM to find the part number for things like this. The Blue Plug is part number 13621709966
'89 325i Touring | Touring Resto Thread | In-Dash Screen install
-
gingerrusta
- E30 Zone Regular

- Posts: 527
- Joined: Fri Jul 31, 2009 11:00 pm
- Location: Bedfordshire
update
Blue temp sensor has been changed. Seems to run alot better but this morning when i took the car to have its Mot it did one of the things it was doing before . Put it into reverse and it cut out.
What else could it be?
Blue temp sensor has been changed. Seems to run alot better but this morning when i took the car to have its Mot it did one of the things it was doing before . Put it into reverse and it cut out.
What else could it be?
-
cecotto479
- Caution Unreliable Seller

- Posts: 2949
- Joined: Sun May 13, 2007 11:00 pm
- Location: On a golf course somewhere probably
Crankcase breathers blocked, split or disconnected accidentally? Dipstick not fully home?
1981 E23 735i
1989 E30 325i Motorsport Convertible
Bavarian Retro - Classic BMW Cars, Parts and Accessories - 12.5% discount for forum members on E30 parts - use voucher code "E30zone" at checkout
1989 E30 325i Motorsport Convertible
Bavarian Retro - Classic BMW Cars, Parts and Accessories - 12.5% discount for forum members on E30 parts - use voucher code "E30zone" at checkout
-
gingerrusta
- E30 Zone Regular

- Posts: 527
- Joined: Fri Jul 31, 2009 11:00 pm
- Location: Bedfordshire
where abouts are these?cecotto479 wrote:Crankcase breathers blocked, split or disconnected accidentally? Dipstick not fully home?
-
gingerrusta
- E30 Zone Regular

- Posts: 527
- Joined: Fri Jul 31, 2009 11:00 pm
- Location: Bedfordshire
car is idling lovely now but emissions are at 9% . What next ?
-
Speedtouch
- Old Skooler

- Posts: 14129
- Joined: Tue Feb 14, 2006 11:00 pm
- Location: Canterbury
What's the mileage? If quite high, it would be worth doing a compression test; all six cylinders should read roughly the same, at around 175-190 psi.
A Gunsons compression gauge can be bought cheaply from Halfords for around £25, and is a good investment, as you can use it to check any other engines you may need to. I've had one for years, and it's been reliable.
http://www.halfords.com/webapp/wcs/stor ... yId_255216
And what spark plugs are you using? The best for M20 engines are the NGK BPR6ES.
A Gunsons compression gauge can be bought cheaply from Halfords for around £25, and is a good investment, as you can use it to check any other engines you may need to. I've had one for years, and it's been reliable.
http://www.halfords.com/webapp/wcs/stor ... yId_255216
And what spark plugs are you using? The best for M20 engines are the NGK BPR6ES.
///M aurice
ECU Upgrade EPROM Chips, £40 posted within the UK. Note these are not Zone chips.
viewtopic.php?f=6&t=279421
ECU Upgrade EPROM Chips, £40 posted within the UK. Note these are not Zone chips.
viewtopic.php?f=6&t=279421
-
gingerrusta
- E30 Zone Regular

- Posts: 527
- Joined: Fri Jul 31, 2009 11:00 pm
- Location: Bedfordshire
car has done 107,000 so nothing major for this engine really. Im not sure what plugs it has in it although they were changed on the last mot a year ago. The car hasnt been used much .
Would the compression make it run rich ??
as you can see from the thread i have changed a few things and cleaned up where possible.
My mate at my local garage thinks it is the AFM as its not adjusting???
Would the compression make it run rich ??
as you can see from the thread i have changed a few things and cleaned up where possible.
My mate at my local garage thinks it is the AFM as its not adjusting???
-
Speedtouch
- Old Skooler

- Posts: 14129
- Joined: Tue Feb 14, 2006 11:00 pm
- Location: Canterbury
Well, if the car hasn't been used much, this may explain the rich running - big engines like this need regular excercise!
Check that the correct spark plugs are fitted and correctly gapped, and go from there.
Check that the correct spark plugs are fitted and correctly gapped, and go from there.
///M aurice
ECU Upgrade EPROM Chips, £40 posted within the UK. Note these are not Zone chips.
viewtopic.php?f=6&t=279421
ECU Upgrade EPROM Chips, £40 posted within the UK. Note these are not Zone chips.
viewtopic.php?f=6&t=279421
-
gingerrusta
- E30 Zone Regular

- Posts: 527
- Joined: Fri Jul 31, 2009 11:00 pm
- Location: Bedfordshire
will try a new set of plugs . Are the ones you mentioned on euro car parts?
-
Speedtouch
- Old Skooler

- Posts: 14129
- Joined: Tue Feb 14, 2006 11:00 pm
- Location: Canterbury
Yes, probably, or available from E-bay, etc.
Just a thought; my first E30, a 320i with L-Jet, failed the MOT one year because of excess emissions, and it had a stripped spark plug thread on one cylinder. When I disconnected the injector to that cylinder, it went down to a passable level!
So, carefully remove the spark plugs, and check that the threads are OK and that they seal properly when tightened up.
Just a thought; my first E30, a 320i with L-Jet, failed the MOT one year because of excess emissions, and it had a stripped spark plug thread on one cylinder. When I disconnected the injector to that cylinder, it went down to a passable level!
So, carefully remove the spark plugs, and check that the threads are OK and that they seal properly when tightened up.
///M aurice
ECU Upgrade EPROM Chips, £40 posted within the UK. Note these are not Zone chips.
viewtopic.php?f=6&t=279421
ECU Upgrade EPROM Chips, £40 posted within the UK. Note these are not Zone chips.
viewtopic.php?f=6&t=279421
-
gingerrusta
- E30 Zone Regular

- Posts: 527
- Joined: Fri Jul 31, 2009 11:00 pm
- Location: Bedfordshire
ok cool will give that a try cheers. Thank you for your ideas and fingers crossed it helps 
Will update when i have done it.
Cheers
Will update when i have done it.
Cheers
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
Examine each spark plug as you remove it, note the colour of the tip, and any differences between them.
-
gingerrusta
- E30 Zone Regular

- Posts: 527
- Joined: Fri Jul 31, 2009 11:00 pm
- Location: Bedfordshire
plugs or afm that is the question 
-
lamby
- E30 Zone Regular

- Posts: 251
- Joined: Wed Jan 27, 2010 11:00 pm
wind the allen bolt on the afm all the way home counting each rotation,if its about 3 that should be ok as it does your mixture.mine was all the way out put it to 2.5 and emissions went just under 1,try it nothing to lose just remember how many turns
