325i engine freshen up list
Moderator: martauto
-
polsta
- Married to the E30 Zone

- Posts: 10322
- Joined: Fri Oct 09, 2009 11:00 pm
- Location: portsmouth
So.. a new thing for me to learn,and im sure would come in useful for many people too that are not too hot on engines and mechanics
with a 325i engine early high compression
what would a freshen up list of parts to service/spruce it up a bit and get it all running nice/its best be
not fluids etc, but other parts , with rough prices and best place to get them from be, and if "vital" or "worthwhile" and "can do" in terms of importance
im talking spark plugs, belts, sensors,distributor/caps,any leads worth upgrading/replacing, and all them sort of things and anything non major on a good engine, thats worth replacing to give it all nice freshen up
just want to get a list up together of what things to gather up and have it all ready to go and rough price im looking at
would appriciate any input
with a 325i engine early high compression
what would a freshen up list of parts to service/spruce it up a bit and get it all running nice/its best be
not fluids etc, but other parts , with rough prices and best place to get them from be, and if "vital" or "worthwhile" and "can do" in terms of importance
im talking spark plugs, belts, sensors,distributor/caps,any leads worth upgrading/replacing, and all them sort of things and anything non major on a good engine, thats worth replacing to give it all nice freshen up
just want to get a list up together of what things to gather up and have it all ready to go and rough price im looking at
would appriciate any input
-
Simon13
- The longest resto in the world !
- Posts: 22697
- Joined: Mon Jan 10, 2005 11:00 pm
- Location: Camberley, Surrey don't u know
theres loads of this advice all over the forum photo gallery/technical/m20 section!
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
For a pre facelift high comp. engine, the first thing to do is bin the primitive management system and upgrade to the considerably more sophisticated M1.3 system from a facelift car.
Apart from that, there's nothing that really can be 'upgraded', since BMW adequately specified everything in the first place. All that needs to be done is to replace anything that's not performing as it was when new, usually starting with the injectors.
Apart from that, there's nothing that really can be 'upgraded', since BMW adequately specified everything in the first place. All that needs to be done is to replace anything that's not performing as it was when new, usually starting with the injectors.
-
Simon13
- The longest resto in the world !
- Posts: 22697
- Joined: Mon Jan 10, 2005 11:00 pm
- Location: Camberley, Surrey don't u know
and knackered a camshaft, blocked spray bar, worn rockers, scored pistons and worn bores. Cranks in need of regrinds and shells along with worn oil pumps.
This is about the state of 95% of M20's left, in need of major top to bottom overhauls. Sad but true
This is about the state of 95% of M20's left, in need of major top to bottom overhauls. Sad but true
-
capri_rob
- Married to the E30 Zone

- Posts: 9678
- Joined: Tue Feb 19, 2008 11:00 pm
- Location: South Staffordshire
As above remove the spraybar, soak it in brake cleaner or something similar, drill out the holes slightly to improve oil flow and blast it through with compressed air before refitting.
Get the valve clearances properly set by someone who knows what they're doing.
Replace distributor cap & rotor arm.
Replace plugs.
Cambelt & tensioner buy the contitech kit from ECP
The rest is just standard service stuff.
Good luck mate - its all worth doing
Get the valve clearances properly set by someone who knows what they're doing.
Replace distributor cap & rotor arm.
Replace plugs.
Cambelt & tensioner buy the contitech kit from ECP
The rest is just standard service stuff.
Good luck mate - its all worth doing

e30topless said : Proper BMW's have 4 headlights, last of the run was the E30 and E34/E32 anything after that is just complete shite
-
polsta
- Married to the E30 Zone

- Posts: 10322
- Joined: Fri Oct 09, 2009 11:00 pm
- Location: portsmouth
thanks rob, what is a spray bar ? its not "upgrade" things im more fussed about, just what items to service and replace that are not too costly, to get it running nice and reliable as possible
so whats imvolved with that motronic thing then in terms of fitting it in ? easy plag and play style or more involved ? and to source one means what- get one of any latter 325i ? or have to be a sport ? what year onwards would it need to be ?
car drives nice, spent a decade in storage, so im hoping the bottom end of the engine will be decent and ok for a few years yet
so whats imvolved with that motronic thing then in terms of fitting it in ? easy plag and play style or more involved ? and to source one means what- get one of any latter 325i ? or have to be a sport ? what year onwards would it need to be ?
car drives nice, spent a decade in storage, so im hoping the bottom end of the engine will be decent and ok for a few years yet
-
Grrrmachine
- E30 Zone Wiki / Team Member

- Posts: 8043
- Joined: Sat Feb 09, 2008 11:00 pm
- Location: Warsaw, Poland
There's no difference at all between a Sport engine and any other 325i engine; you should know that by now. The Upgrade Brian refers to is here:
http://www.e30zone.net/e30zonewiki/inde ... tronic_1.3
And the oil spray bar is underneath the rocker cover. It sprays oil over the valve train.
http://www.e30zone.net/e30zonewiki/inde ... tronic_1.3
And the oil spray bar is underneath the rocker cover. It sprays oil over the valve train.
'89 325i Touring | Touring Resto Thread | In-Dash Screen install
-
polsta
- Married to the E30 Zone

- Posts: 10322
- Joined: Fri Oct 09, 2009 11:00 pm
- Location: portsmouth
of course i know that, but dont know anything about the electrical side and ecu, thanks for the info
in moneytary terms ££ ...how much does a full swap over to 1.3 cost roughly inc all parts and labour ?
in moneytary terms ££ ...how much does a full swap over to 1.3 cost roughly inc all parts and labour ?
-
bss325i
- E30 Zone Team Member

- Posts: 24532
- Joined: Sat Jan 20, 2007 11:00 pm
- Location: London/Surrey
Clean the throttle switch out, it WILL be full of oil and check that it is set correctly so the idle and WOT are being switched properly.
-
adit
- Married to the E30 Zone

- Posts: 13727
- Joined: Wed Jun 20, 2007 11:00 pm
- Location: portsmouth
good thread Carl and all helpful and positive comments from everyone above, there's a zone first! 

E30 Parts Galore!! 07901 888019
[quote="bss325i"]
Get a f* grip,we are talking about 20+yr.old sub £10k cars here,NOT the crown jewels!
-
Kedge
- Old Skooler

- Posts: 7698
- Joined: Thu Jan 13, 2005 11:00 pm
- Location: Leicestershire
Since you missed/ignored it on the other thread you asked the very same questions;
bss325i wrote:AND it comes with the desirable 173 ECU.Kedge wrote:As per most technical questions, there's extensive threads on here all about it and a wiki guide written by my very own hand.polsta wrote:so whats imvolved with that motronic thing then in terms of fitting it in ? easy plag and play style or more involved ? and to source one means what- get one of any latter 325i ? or have to be a sport ? what year onwards would it need to be ?
All plug and play really, bar two wires that need cutting and moving to get the clocks working properly .Trev (B7) is selling a complete kit for £50, BARGAIN!!
-
Blitz
- Married to the E30 Zone

- Posts: 11151
- Joined: Mon Jan 30, 2006 11:00 pm
- Location: East London+Basildon
I dont see the point of messing around changing the engine management system if theres nothing wrong with the one you got.
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
Do you still use windows 95?Blitz wrote:I dont see the point of messing around changing the engine management system if theres nothing wrong with the one you got.
-
polsta
- Married to the E30 Zone

- Posts: 10322
- Joined: Fri Oct 09, 2009 11:00 pm
- Location: portsmouth
would this be the case ? no nothing is wrong with mine and engine was fully operational, although now been sat for 9 months without much useBlitz wrote:I dont see the point of messing around changing the engine management system if theres nothing wrong with the one you got.
its more things like the dizzy cap and belts and general parts like that i was originaly thinking about replacing, good measure type things and get it all 100%
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
The change in engine management was the reason that BMW could drop the compression ratio of the engine considerably, and not loose any performance.
-
bmw9818
- E30 Zone Addict

- Posts: 2561
- Joined: Tue Aug 11, 2009 11:00 pm
- Location: Croydon
so are there any advantages performance wise possibly? with a high comp engine converted to 1.3...Brianmoooore wrote:The change in engine management was the reason that BMW could drop the compression ratio of the engine considerably, and not loose any performance.
-
polsta
- Married to the E30 Zone

- Posts: 10322
- Joined: Fri Oct 09, 2009 11:00 pm
- Location: portsmouth
or is it better to leave on the standard then if not ?bmw9818 wrote:so are there any advantages performance wise possibly? with a high comp engine converted to 1.3...Brianmoooore wrote:The change in engine management was the reason that BMW could drop the compression ratio of the engine considerably, and not loose any performance.
how about fuel performance/fuel econemy both ways ?
-
bss325i
- E30 Zone Team Member

- Posts: 24532
- Joined: Sat Jan 20, 2007 11:00 pm
- Location: London/Surrey
None unless you have it remapped, something 1.3 is easier to do.bmw9818 wrote:so are there any advantages performance wise possibly? with a high comp engine converted to 1.3...Brianmoooore wrote:The change in engine management was the reason that BMW could drop the compression ratio of the engine considerably, and not loose any performance.
-
Barx325i
- Engaged to the E30 Zone

- Posts: 6493
- Joined: Wed Jul 26, 2006 11:00 pm
fundamentally 1.3 offers a far more detailed resoltion of data for the ecu to process and pass on.
withstanding any servicing items, a throttle body heater jacket bypass is worthy of the labour
withstanding any servicing items, a throttle body heater jacket bypass is worthy of the labour

