M3 rear bench.

General E30 related discussions -
Please put technical questions in E30 Tech Help forum below

Moderator: martauto

kitch
E30 Zone Regular
E30 Zone Regular
Posts: 878
Joined: Sat Nov 01, 2008 11:00 pm

Post Sun May 13, 2012 12:46 pm

Will an M3 rear bench fit in a 4door? Or are the corner bits of the base different?

TIA
Image
User avatar
Steve
E30 Zone Team Member
E30 Zone Team Member
Posts: 13158
Joined: Sun Dec 19, 2004 11:00 pm

Post Sun May 13, 2012 4:55 pm

I have one fitted in mine no mods needed, it's looks bigger than the standard bench though.

I'll try and get some photos if you think it will help :thumb:
webmaster@e30zone.net
Simon
E30 Zone Team Member
E30 Zone Team Member
Posts: 14939
Joined: Sun Jan 09, 2005 11:00 pm
Location: South Wales

Post Sun May 13, 2012 5:24 pm

As you've pointed out, the corners on the base are different, 4 door bases have a curved corner to make getting out easier, but a 2 door/M3 base will still fit fine.
Image
magpie
Old Skooler
Old Skooler
Posts: 28035
Joined: Sun Jun 29, 2008 11:00 pm
Location: Consett,Durham.

Post Sun May 13, 2012 5:25 pm

don't listen to them,it wont fit and you should sell it to me :D
Image
m52 b30 stroker 6-speed 318is Galvanizer
m42 touring
+ a yard full of scrap turds :)
suchy
True Zone Relic
Posts: 6604
Joined: Tue Apr 26, 2005 11:00 pm
Location: Portsmouth

Post Sun May 13, 2012 8:43 pm

It will fit but you will need cabrio female belt clips as the normal E30 bench doesn't have the raised middle section and the inset clip holders are higher (if that makes sense!) 8)
baur320
E30 Zone Squatter
E30 Zone Squatter
Posts: 1507
Joined: Wed Jan 12, 2005 11:00 pm
Location: Tyneside

Post Sun May 13, 2012 9:34 pm

I know what you mean. I've an M3 rear seat in my 2 door and the buckles don't fit into the holders in the back section because the webbing is too short.

I checked realoem at the time and was sure that all centre buckles were the same so presumed an M3 shell had a diffent mounting point.

You sure about cab buckles?
Current E30 325i, E63 630is.
Previous E21 320/4, E9 3.0 CSA, E12 525, E30 320i, E28 528i, E34 535is, E30 318i, E28 525e, E30 325i Touring, E30 Baur 327i, E36 M3 Evo, X3is, E39 530d M Sport.
suchy
True Zone Relic
Posts: 6604
Joined: Tue Apr 26, 2005 11:00 pm
Location: Portsmouth

Post Mon May 14, 2012 8:29 am

They have the same rear seat shape don't they? :D
Don't know about a different mounting point though as I don't have an M3 to compare!

Anyone...????
Simon
E30 Zone Team Member
E30 Zone Team Member
Posts: 14939
Joined: Sun Jan 09, 2005 11:00 pm
Location: South Wales

Post Mon May 14, 2012 8:50 am

The mounting point on the M3 is different, I had in interior out of an M3 in a scrapyard years ago, on finding out the centre buckle in my 2 door didn't fit I went back for the buckle out of the M3 and found it was the same as the one already fitted.
Image
suchy
True Zone Relic
Posts: 6604
Joined: Tue Apr 26, 2005 11:00 pm
Location: Portsmouth

Post Mon May 14, 2012 8:52 am

Simon wrote:The mounting point on the M3 is different, I had in interior out of an M3 in a scrapyard years ago, on finding out the centre buckle in my 2 door didn't fit I went back for the buckle out of the M3 and found it was the same as the one already fitted.
So does that mean cabs have the same mounting point as M3's then or do they have special buckles??
baur320
E30 Zone Squatter
E30 Zone Squatter
Posts: 1507
Joined: Wed Jan 12, 2005 11:00 pm
Location: Tyneside

Post Mon May 14, 2012 9:00 am

What did you do in the end Simon? Don't fancy creasing the seat just to get the buckles in the holders.

Image
Current E30 325i, E63 630is.
Previous E21 320/4, E9 3.0 CSA, E12 525, E30 320i, E28 528i, E34 535is, E30 318i, E28 525e, E30 325i Touring, E30 Baur 327i, E36 M3 Evo, X3is, E39 530d M Sport.
Simon
E30 Zone Team Member
E30 Zone Team Member
Posts: 14939
Joined: Sun Jan 09, 2005 11:00 pm
Location: South Wales

Post Mon May 14, 2012 9:12 am

IIRC, I managed to get them into the slots, but they didn't fit all the way upto the top, so never looked tidy.
Image
daimlerman
**BANNED**
Posts: 15968
Joined: Mon Feb 27, 2006 11:00 pm
Location: Grumpy Old Man

Post Mon May 14, 2012 9:18 am

On cabbies,the rear bulkhead has all the same mounting points as a saloon,but they are used differently.

The outer seatbelt mounts are used to retain the seat back,and the centre belt mount is used for the double female buckle,where the third,single,female buckle bolts in on a saloon.

Never played with an M3,so I have no information about the arrangement there!
Youth is wasted on the young.
kieran325
Old Skooler
Old Skooler
Posts: 5015
Joined: Sun Oct 30, 2005 11:00 pm

Post Mon May 14, 2012 9:22 am

Image

Image

Any good.
daimlerman
**BANNED**
Posts: 15968
Joined: Mon Feb 27, 2006 11:00 pm
Location: Grumpy Old Man

Post Mon May 14, 2012 9:26 am

For the purpose of improving my knowledge,Kieran,does the M3 backrest bolt in via two 10mm bolts,as in a 'normal' saloon?
Youth is wasted on the young.
kieran325
Old Skooler
Old Skooler
Posts: 5015
Joined: Sun Oct 30, 2005 11:00 pm

Post Mon May 14, 2012 9:48 am

Yes it does, same fittings for both.
kitch
E30 Zone Regular
E30 Zone Regular
Posts: 878
Joined: Sat Nov 01, 2008 11:00 pm

Post Mon May 14, 2012 8:30 pm

Thanks for all the info :D . Looks like this could get expensive haha
Image
User avatar
Jozi
E30 Zone Addict
E30 Zone Addict
Posts: 3076
Joined: Thu Nov 22, 2007 11:00 pm
Location: Dublin, Ireland

Post Mon May 14, 2012 9:26 pm

Does that meant the bas will also fit a touring? I'd love a m3 styled rear bench 8) It's no good anyway for 3 people, not that it's ever used
daimlerman
**BANNED**
Posts: 15968
Joined: Mon Feb 27, 2006 11:00 pm
Location: Grumpy Old Man

Post Mon May 14, 2012 9:34 pm

Jozi wrote:Does that meant the bas will also fit a touring? I'd love a m3 styled rear bench 8) It's no good anyway for 3 people, not that it's ever used
Best bet for a proper E30(touring)would be a custom re-trim of the existing seat frames,then use two single seatbelt fittings into the standard mount points.

Remember that the saloons(lesser E30)use a structural rear bulkhead,this is replaced in touring with a stiffened floor and rear suspension upper mounts.
User avatar
Jozi
E30 Zone Addict
E30 Zone Addict
Posts: 3076
Joined: Thu Nov 22, 2007 11:00 pm
Location: Dublin, Ireland

Post Mon May 14, 2012 9:47 pm

daimlerman wrote:
Best bet for a proper E30(touring)would be a custom re-trim of the existing seat frames,then use two single seatbelt fittings into the standard mount points.
I'm thinking if I ever get it retrimmed to get them to mould a M3 type bench and get rid of the middle. Might not fold forward anymore but feck that anyway - my touring will be far from a work horse when finished.
suchy
True Zone Relic
Posts: 6604
Joined: Tue Apr 26, 2005 11:00 pm
Location: Portsmouth

Post Tue May 15, 2012 11:44 am

daimlerman wrote:On cabbies,the rear bulkhead has all the same mounting points as a saloon,but they are used differently.

The outer seatbelt mounts are used to retain the seat back,and the centre belt mount is used for the double female buckle,where the third,single,female buckle bolts in on a saloon.

Never played with an M3,so I have no information about the arrangement there!
Ahh cheers didn't think of that- don't need the third belt anyway with an M3 bench :D