Engine fooked :(
Moderator: martauto
-
DanThe
- E30 Zone Team Member

- Posts: 28649
- Joined: Sat Sep 10, 2005 11:00 pm
- Location: Staffs
Could the vacuum from the inlet collapse it?
-
eko
- Old timer
- Posts: 11531
- Joined: Sat Feb 05, 2005 11:00 pm
- Location: South Devon
Ill run the breather from the cam cover into a bottle and run it up the road to see how much oil is pushed out.

-
adit
- Married to the E30 Zone

- Posts: 13727
- Joined: Wed Jun 20, 2007 11:00 pm
- Location: portsmouth
that'll be next "Summer" theneko wrote:Yep,fooking thing can wait till it stops raining though,cant even be arsed to go out to itDanThe wrote:Next job = compression test
sorry to hear this Tony, hope it's not as bad as you fear
Last edited by adit on Thu May 10, 2012 10:33 pm, edited 1 time in total.

E30 Parts Galore!! 07901 888019
[quote="bss325i"]
Get a f* grip,we are talking about 20+yr.old sub £10k cars here,NOT the crown jewels!
-
eko
- Old timer
- Posts: 11531
- Joined: Sat Feb 05, 2005 11:00 pm
- Location: South Devon
Right just finished having a look at it.
Disconnected the breather from the MAF pipe and ran it into a coke bottle.
Just took it on a 10 minute drive and checked the bottle,its empty with just a small trace of spatter inside it,also the smoke seems to have cleared.
It has to be my lashed up breather causing the problem.
For 18 months the 2 pieces of hose have just been secured with a cable tie.
When I sorted the split ICV hose recently I replaced the cable tie with the jubilee clip.
Heres a shamefull pic of my bodge....

So plan is ill do the job properly this time and just get the correct size hose and try it with that.
Will report back tomorrow when ive done it:?
Disconnected the breather from the MAF pipe and ran it into a coke bottle.
Just took it on a 10 minute drive and checked the bottle,its empty with just a small trace of spatter inside it,also the smoke seems to have cleared.
It has to be my lashed up breather causing the problem.
For 18 months the 2 pieces of hose have just been secured with a cable tie.
When I sorted the split ICV hose recently I replaced the cable tie with the jubilee clip.
Heres a shamefull pic of my bodge....

So plan is ill do the job properly this time and just get the correct size hose and try it with that.
Will report back tomorrow when ive done it:?

-
magpie
- Old Skooler

- Posts: 28035
- Joined: Sun Jun 29, 2008 11:00 pm
- Location: Consett,Durham.
things are sounding good .


m52 b30 stroker 6-speed 318is Galvanizer
m42 touring
+ a yard full of scrap turds
-
Jhonno
- Homo Hair
- Posts: 20362
- Joined: Mon Jan 10, 2005 11:00 pm
- Location: FLAT, FLAT, FLAT!!
Fingers crossed for you Tony!!
-
grantfk10
- E30 Zone Meets/Events Team

- Posts: 2926
- Joined: Mon Jan 17, 2005 11:00 pm
- Location: UFOland, Central Scotland
eko wrote:.
It has to be my lashed up breather causing the problem.
For 18 months the 2 pieces of hose have just been secured with a cable tie.
When I sorted the split ICV hose recently I replaced the cable tie with the jubilee clip.
Heres a shamefull pic of my bodge....
So plan is ill do the job properly this time and just get the correct size hose and try it with that.
Will report back tomorrow when ive done it:?
Hope it all works out ok for you.
The above is one of the major reasons I wouldn't consider buying a car with an engine swap tho. You never know, despite how good an E30 "enthusiast" is at transplanting engines, just what has been "bodged".
Even if that make-shift job has lasted for a while, it still isn't right.....
I'll wait to be flamed now
-
eko
- Old timer
- Posts: 11531
- Joined: Sat Feb 05, 2005 11:00 pm
- Location: South Devon
lolgrantfk10 wrote:
The above is one of the major reasons I wouldn't consider buying a car with an engine swap tho. You never know, despite how good an E30 "enthusiast" is at transplanting engines, just what has been "bodged".
Even if that make-shift job has lasted for a while, it still isn't right.....
I'll wait to be flamed now
Probably not a good time to show you a pic of my engine mountings made out of lego then

-
78gizmo
- E30 Zone Regular

- Posts: 265
- Joined: Fri Nov 16, 2007 11:00 pm
- Location: Torbay, South Devon
Yet more proof cable ties are the best solution for fixing cars!eko wrote: For 18 months the 2 pieces of hose have just been secured with a cable tie.
When I sorted the split ICV hose recently I replaced the cable tie with the jubilee clip.
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
Should have just kept quiet, and turned up at your house tomorrow with the trailer and a handful of folding stuff! I've just missed a cheap, tidy M52 touring. 
-
grantfk10
- E30 Zone Meets/Events Team

- Posts: 2926
- Joined: Mon Jan 17, 2005 11:00 pm
- Location: UFOland, Central Scotland
That was my plan for my touring, but need to know it's done properly. How difficult was it?78gizmo wrote:I have got the white touring on the road at last (now with M42).
-
eko
- Old timer
- Posts: 11531
- Joined: Sat Feb 05, 2005 11:00 pm
- Location: South Devon
See you at 4.30 thenBrianmoooore wrote:Should have just kept quiet, and turned up at your house tomorrow with the correct size hose,some new clips and a lecture on how to do the job properly to start with

-
eko
- Old timer
- Posts: 11531
- Joined: Sat Feb 05, 2005 11:00 pm
- Location: South Devon
How you doing mate?78gizmo wrote:Yet more proof cable ties are the best solution for fixing cars!eko wrote: For 18 months the 2 pieces of hose have just been secured with a cable tie.
When I sorted the split ICV hose recently I replaced the cable tie with the jubilee clip.Glad it looks like its sorted mate. BTW I have got the white touring on the road at last (now with M42).
Finally got the Touring up and running then.
They respond well to the M42,ive done a couple now.
You been in Gormans lately?
Keep meaning to pop in to see whats in but weather always shit and need waders in that place

-
78gizmo
- E30 Zone Regular

- Posts: 265
- Joined: Fri Nov 16, 2007 11:00 pm
- Location: Torbay, South Devon
Sorry to thread hijack Tony!grantfk10 wrote:That was my plan for my touring, but need to know it's done properly. How difficult was it?78gizmo wrote:I have got the white touring on the road at last (now with M42).
Its a dead easy swap, just took me ages to finish off and Mot due to lack of spare time. Assuming you have an M40 in it now you just need an M42 with loom, ecu, full exhaust and coil pack. The M42 will go straight onto the original gearbox, you may need to change the spigot bearing. I also had to use my M40 engine mounting arms, but its all pretty much plug and play other than making a bracket for the coil pack.
-
78gizmo
- E30 Zone Regular

- Posts: 265
- Joined: Fri Nov 16, 2007 11:00 pm
- Location: Torbay, South Devon
Am good thanks mate and pleased with the M42 conversion, it goes better than i expected. There were a couple of poverty spec 4pot tourings with just about everything trashed last time i went to gormans but the high tide has kept me away for a month or so!eko wrote:How you doing mate?78gizmo wrote:Yet more proof cable ties are the best solution for fixing cars!eko wrote: For 18 months the 2 pieces of hose have just been secured with a cable tie.
When I sorted the split ICV hose recently I replaced the cable tie with the jubilee clip.Glad it looks like its sorted mate. BTW I have got the white touring on the road at last (now with M42).
Finally got the Touring up and running then.
They respond well to the M42,ive done a couple now.
You been in Gormans lately?
Keep meaning to pop in to see whats in but weather always shit and need waders in that place
-
grantfk10
- E30 Zone Meets/Events Team

- Posts: 2926
- Joined: Mon Jan 17, 2005 11:00 pm
- Location: UFOland, Central Scotland
Thanx for that 78gizmo, might loook into that if the touring is a keeper
And it's pretty solid anyway.
-
G-Bear
- E30 Zone Squatter

- Posts: 1631
- Joined: Wed Mar 12, 2008 11:00 pm
- Location: Hertfordshire
eko wrote:lolgrantfk10 wrote:
The above is one of the major reasons I wouldn't consider buying a car with an engine swap tho. You never know, despite how good an E30 "enthusiast" is at transplanting engines, just what has been "bodged".
Even if that make-shift job has lasted for a while, it still isn't right.....
I'll wait to be flamed now
Probably not a good time to show you a pic of my engine
mountings made out of lego then
My Dad has used Lego on his cars in the past. He also cut a handle off a wheel barrow to weld to a tailpipe to get it through an MOT..
Hope the breather pipes the problem and that it's running good again soon..
-
eko
- Old timer
- Posts: 11531
- Joined: Sat Feb 05, 2005 11:00 pm
- Location: South Devon
Tragedy averted 
Replaced the breather pipe and also put a new rocker cover gasket on.
Tin of carb cleaner through the TB and took it on a good run to clear the exhaust out.
All traces of Blue smoke have gone and back to running how it should be.
Thanks to those giving advice,im a happy chap again now
Replaced the breather pipe and also put a new rocker cover gasket on.
Tin of carb cleaner through the TB and took it on a good run to clear the exhaust out.
All traces of Blue smoke have gone and back to running how it should be.
Thanks to those giving advice,im a happy chap again now

-
Speedtouch
- Old Skooler

- Posts: 14130
- Joined: Tue Feb 14, 2006 11:00 pm
- Location: Canterbury
I have also done the wheel barrow handle exhaust bodge - someone else's suggestion, when I happened to need an extra 4" or so spliced in. It was a perfect match, and survives to this day, some 2 years on!G-Bear wrote:My Dad has used Lego on his cars in the past. He also cut a handle off a wheel barrow to weld to a tailpipe to get it through an MOT..
///M aurice
ECU Upgrade EPROM Chips, £40 posted within the UK. Note these are not Zone chips.
viewtopic.php?f=6&t=279421
ECU Upgrade EPROM Chips, £40 posted within the UK. Note these are not Zone chips.
viewtopic.php?f=6&t=279421
-
DanThe
- E30 Zone Team Member

- Posts: 28649
- Joined: Sat Sep 10, 2005 11:00 pm
- Location: Staffs
What about the wheel barrow though?
-
Speedtouch
- Old Skooler

- Posts: 14130
- Joined: Tue Feb 14, 2006 11:00 pm
- Location: Canterbury
Rest assured, it was a shagged turd of a barrow, thrown away for scrap.
///M aurice
ECU Upgrade EPROM Chips, £40 posted within the UK. Note these are not Zone chips.
viewtopic.php?f=6&t=279421
ECU Upgrade EPROM Chips, £40 posted within the UK. Note these are not Zone chips.
viewtopic.php?f=6&t=279421
-
andyp
- True Old Skooler
- Posts: 6899
- Joined: Sun Jan 09, 2005 11:00 pm
- Location: LONDON
tell her i said to stop the drifting on the way there and back lol
-
grantfk10
- E30 Zone Meets/Events Team

- Posts: 2926
- Joined: Mon Jan 17, 2005 11:00 pm
- Location: UFOland, Central Scotland
I have an old wheelbarrow that I was gonna take to the dump. Reckon I'll hang onto it for a bit longer now 
-
adit
- Married to the E30 Zone

- Posts: 13727
- Joined: Wed Jun 20, 2007 11:00 pm
- Location: portsmouth
good news Tony 

E30 Parts Galore!! 07901 888019
[quote="bss325i"]
Get a f* grip,we are talking about 20+yr.old sub £10k cars here,NOT the crown jewels!
-
G-Bear
- E30 Zone Squatter

- Posts: 1631
- Joined: Wed Mar 12, 2008 11:00 pm
- Location: Hertfordshire
Just happen to be at my parents at the moment. Popped into the garden. The one handled wheel barrow is still there some 15 years on, next to a shinier one with both handles on.. Must be saving it for another MOT..DanThe wrote:What about the wheel barrow though?
Good news about the engine eko...


