Thanks
e30 maxes out at 5000 revs
Moderator: martauto
-
matt86
- E30 Zone Addict

- Posts: 2468
- Joined: Thu Jan 19, 2012 11:00 pm
- Location: "The Cotswolds" Stroud, Gloucestershire
Hi my e30 1.8 convertible maxes out at 5000 revs, is this a fault, or is this what its limited too, I'm just worried I may have a worn camshaft, as it is hesistant too sometimes, was going to give it a full service anyway, but am thinking of doing a engine conversion shortly when I have the money.
Thanks

Thanks
-
darkchild
- E30 Zone Addict

- Posts: 2729
- Joined: Mon Feb 06, 2006 11:00 pm
- Location: Kingston 12
Very likely. Sounds like a typical neglected M40 I'm afraid.matt86 wrote:I'm just worried I may have a worn camshaft
-
flybmw
- E30 Zone Newbie

- Posts: 235
- Joined: Mon Mar 12, 2012 11:00 pm
I have the same thing. How can I be sure that it is a problem with a camshaft? How can I fix that? Sorry for stupid question.
My car (running M40) revs to 5 000rpm, hesitates and then shift to next gear (Auto tranny). What could be causing it? It does not rev higher than 5k rpms.
Thanks
My car (running M40) revs to 5 000rpm, hesitates and then shift to next gear (Auto tranny). What could be causing it? It does not rev higher than 5k rpms.
Thanks
-
Rtaylor2208
- E30 Zone Addict

- Posts: 3004
- Joined: Mon Oct 11, 2010 11:00 pm
- Location: Ayr, Ayrshire, Scotland
-
matt86
- E30 Zone Addict

- Posts: 2468
- Joined: Thu Jan 19, 2012 11:00 pm
- Location: "The Cotswolds" Stroud, Gloucestershire
I think we both have the same issue and need a new or 2nd hand camshaft fitting, I'd say best to try a service first, correct me if I'm wrong.
Was thinking of engine conversion anyway, but how long will it last and will it eventually do long term damage to engine, or will the lobes just be worn, the engine itself in mine is currently quite quiet, no rattles, knocks etc
Was thinking of engine conversion anyway, but how long will it last and will it eventually do long term damage to engine, or will the lobes just be worn, the engine itself in mine is currently quite quiet, no rattles, knocks etc
-
BenHar
- E30 Zone Addict

- Posts: 3089
- Joined: Sun Jul 11, 2010 11:00 pm
- Location: Reigate, Surrey
Haven't you done this yet?matt86 wrote: try a service first
Spent all your money on polish?
Ben
-
pacerpete
- E30 Zone Team Member

- Posts: 18165
- Joined: Sun Jan 23, 2005 11:00 pm
- Location: Iver heath. South bucks.
BenHar wrote:Haven't you done this yet?matt86 wrote: try a service first
Spent all your money on council bits ?
Ben
-
matt86
- E30 Zone Addict

- Posts: 2468
- Joined: Thu Jan 19, 2012 11:00 pm
- Location: "The Cotswolds" Stroud, Gloucestershire
pacerpete wrote:BenHar wrote:Haven't you done this yet?matt86 wrote: try a service first
Spent all your money on council bits ?
Ben
Yes Ben didn't get my priorities right, put too much money into tarting the car up, rather than sorting the mechanical side first. next payday in a couple of weeks I will service it, and check everything else over on the car.
It's not being driven at the moment anyway.
-
maggspower
- Turbo Farmer Tractor Driver
- Posts: 2376
- Joined: Wed Oct 12, 2005 11:00 pm
- Location: Nowhere near South Wales, ok butt
I am by no means an expert on the m40 engine, but worn valve springs would cause your problem, and have heard that these can suffer from this, the springs become too weak to close the valves quick enough at high revs causing a symptom called valve bounce. If the valves are not seating as they should you get less compression, one of the key ingredients that an internal combustion engine relies on to produce power.
In truth it is more than likley that the symptoms are caused by wear in multiple components in the valve train and not one specific part, these engine are 20 years old plus, and unless low milage and well looked after they will need perodical maintenance.
HTH
In truth it is more than likley that the symptoms are caused by wear in multiple components in the valve train and not one specific part, these engine are 20 years old plus, and unless low milage and well looked after they will need perodical maintenance.
HTH
