Painting subframe and trailing arms

Need technical Q/A then you're in the right place

Moderator: martauto

Grrrmachine
E30 Zone Wiki / Team Member
E30 Zone Wiki / Team Member
Posts: 8043
Joined: Sat Feb 09, 2008 11:00 pm
Location: Warsaw, Poland

Post Fri Jan 27, 2012 6:15 am

Hopefully the back end will be reattached to the car this weekend, so I figured I'd paint what I can before it all goes back together.

Is there any special technique or prep I should do, or is it just a good degrease and loads of Hammerite?
User avatar
redcar
E30 Zone Squatter
E30 Zone Squatter
Posts: 1610
Joined: Wed Jul 20, 2011 11:00 pm
Location: Hertfordshire

Post Fri Jan 27, 2012 6:42 am

Shot blasted then powder coat :)
Grrrmachine
E30 Zone Wiki / Team Member
E30 Zone Wiki / Team Member
Posts: 8043
Joined: Sat Feb 09, 2008 11:00 pm
Location: Warsaw, Poland

Post Fri Jan 27, 2012 6:45 am

No time or money for that. The best these things are getting is a brass brush on the drill :D
capri_rob
Married to the E30 Zone
Married to the E30 Zone
Posts: 9678
Joined: Tue Feb 19, 2008 11:00 pm
Location: South Staffordshire

Post Fri Jan 27, 2012 7:33 am

Grrrmachine wrote:No time or money for that. The best these things are getting is a brass brush on the drill :D
I did that on my beam and it didnt really touch it :(

It will clean it up a bit but won't get in the fiddly bits and won't get a good smooth surface.

Blasting & powdercoating is really the way to go :

Image

Image

I did my front subframe in smoothrite and whilst it looked OK its not a patch on a powdercoated finish :

Image
Image

e30topless said : Proper BMW's have 4 headlights, last of the run was the E30 and E34/E32 anything after that is just complete shite
User avatar
eire30
E30 Zone Newbie
E30 Zone Newbie
Posts: 90
Joined: Mon Jul 12, 2010 11:00 pm
Location: Wicklow

Post Fri Jan 27, 2012 9:05 am

wish my dog could do powder coating as well as that....would save me a fortune! :D
Jos
E30 Zone Camper
E30 Zone Camper
Posts: 1104
Joined: Mon Jan 17, 2005 11:00 pm
Location: Belfast

Post Fri Jan 27, 2012 9:28 am

Grrrmachine wrote:No time or money for that. The best these things are getting is a brass brush on the drill :D
get one of those twist wire brushes for the grinder, lethal on limbs but effective for cleaning the main areas. The niggle bits where the trailing arms will still need some manual scraping.
'89 Touring - slightly rippled with a rusty underside
'94 e36 tree climber
User avatar
Brianmoooore
E30 Zone Team Member
E30 Zone Team Member
Posts: 49360
Joined: Mon Jan 10, 2005 11:00 pm

Post Fri Jan 27, 2012 9:30 am

Wouldn't recommend Hammerite for car applications. It has to be laid on in extremely thick layers and is very brittle and easily chipped as a result. I normally use black enamel intended for agricultural use.
Jhonno
Homo Hair
Posts: 20362
Joined: Mon Jan 10, 2005 11:00 pm
Location: FLAT, FLAT, FLAT!!

Post Fri Jan 27, 2012 9:32 am

POR15
Got cable ties? Get diffin..

Arch roller for hire.

www.zeroexhausts.co.uk

Image
User avatar
Jozi
E30 Zone Addict
E30 Zone Addict
Posts: 3076
Joined: Thu Nov 22, 2007 11:00 pm
Location: Dublin, Ireland

Post Fri Jan 27, 2012 11:00 am

Brianmoooore wrote:Wouldn't recommend Hammerite for car applications. It has to be laid on in extremely thick layers and is very brittle and easily chipped as a result. I normally use black enamel intended for agricultural use.
I agree with this, I painted up parts with hammerite and the slightest knock makes it chip. Their primer on the other hand seemed to hold up well!

Knotted wirewheel for cleaning :thumb:
Grrrmachine
E30 Zone Wiki / Team Member
E30 Zone Wiki / Team Member
Posts: 8043
Joined: Sat Feb 09, 2008 11:00 pm
Location: Warsaw, Poland

Post Fri Jan 27, 2012 11:55 am

I'll switch to the grinder then. And I've picked up some enamel paint for metal, so I'll give that a go.

It doesn't need to be pretty, it just needs to stop the winter salt eating away any more of my car :D
Jhonno
Homo Hair
Posts: 20362
Joined: Mon Jan 10, 2005 11:00 pm
Location: FLAT, FLAT, FLAT!!

Post Fri Jan 27, 2012 2:02 pm

POR15 as my post above. Rock 'ard innit.
Got cable ties? Get diffin..

Arch roller for hire.

www.zeroexhausts.co.uk

Image
Grrrmachine
E30 Zone Wiki / Team Member
E30 Zone Wiki / Team Member
Posts: 8043
Joined: Sat Feb 09, 2008 11:00 pm
Location: Warsaw, Poland

Post Fri Jan 27, 2012 2:34 pm

Can't get it over here though Jhonno. If it's got a brand name, I can't get it.
DanThe
E30 Zone Team Member
E30 Zone Team Member
Posts: 28649
Joined: Sat Sep 10, 2005 11:00 pm
Location: Staffs

Post Fri Jan 27, 2012 9:31 pm

If your not going to go through proper paint stages with decent (expensive) gear then you may as well just wire brush it all by hand and bang a load of waxoil on. It will stop any rusting that is going on and keep water out of all other areas. Removing the coating down to bare metal is a bad move if your not going to replace it properly.
bigbird76
E30 Zone Regular
E30 Zone Regular
Posts: 571
Joined: Sat Feb 16, 2008 11:00 pm
Location: Swansea Wales UK

Post Sat Jan 28, 2012 10:10 am

POR 15 here also


Image

Image

Image

Image

Image

Image

Image

Leigh
Grrrmachine
E30 Zone Wiki / Team Member
E30 Zone Wiki / Team Member
Posts: 8043
Joined: Sat Feb 09, 2008 11:00 pm
Location: Warsaw, Poland

Post Sat Jan 28, 2012 11:21 am

All good info, cheers guys. I've attacked it with the angle gringer/knot brush, but not to the point of removing all the existing coating; just the scabs and pimples where the rust has taken hold. Then things got a wipe down with degreaser, and then slapping on this enamel stuff; thinned a little because it's so cold here at the moment (minus 12!)

So we'll see how it holds. Not a pro job, but can't be worse than leaving the rust to fester.