Painting subframe and trailing arms
Moderator: martauto
-
Grrrmachine
- E30 Zone Wiki / Team Member

- Posts: 8043
- Joined: Sat Feb 09, 2008 11:00 pm
- Location: Warsaw, Poland
Hopefully the back end will be reattached to the car this weekend, so I figured I'd paint what I can before it all goes back together.
Is there any special technique or prep I should do, or is it just a good degrease and loads of Hammerite?
Is there any special technique or prep I should do, or is it just a good degrease and loads of Hammerite?
'89 325i Touring | Touring Resto Thread | In-Dash Screen install
-
redcar
- E30 Zone Squatter

- Posts: 1610
- Joined: Wed Jul 20, 2011 11:00 pm
- Location: Hertfordshire
Shot blasted then powder coat 
-
Grrrmachine
- E30 Zone Wiki / Team Member

- Posts: 8043
- Joined: Sat Feb 09, 2008 11:00 pm
- Location: Warsaw, Poland
No time or money for that. The best these things are getting is a brass brush on the drill 
'89 325i Touring | Touring Resto Thread | In-Dash Screen install
-
capri_rob
- Married to the E30 Zone

- Posts: 9678
- Joined: Tue Feb 19, 2008 11:00 pm
- Location: South Staffordshire
I did that on my beam and it didnt really touch itGrrrmachine wrote:No time or money for that. The best these things are getting is a brass brush on the drill
It will clean it up a bit but won't get in the fiddly bits and won't get a good smooth surface.
Blasting & powdercoating is really the way to go :


I did my front subframe in smoothrite and whilst it looked OK its not a patch on a powdercoated finish :


e30topless said : Proper BMW's have 4 headlights, last of the run was the E30 and E34/E32 anything after that is just complete shite
-
eire30
- E30 Zone Newbie

- Posts: 90
- Joined: Mon Jul 12, 2010 11:00 pm
- Location: Wicklow
wish my dog could do powder coating as well as that....would save me a fortune! 
-
Jos
- E30 Zone Camper

- Posts: 1104
- Joined: Mon Jan 17, 2005 11:00 pm
- Location: Belfast
get one of those twist wire brushes for the grinder, lethal on limbs but effective for cleaning the main areas. The niggle bits where the trailing arms will still need some manual scraping.Grrrmachine wrote:No time or money for that. The best these things are getting is a brass brush on the drill
'89 Touring - slightly rippled with a rusty underside
'94 e36 tree climber
'94 e36 tree climber
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
Wouldn't recommend Hammerite for car applications. It has to be laid on in extremely thick layers and is very brittle and easily chipped as a result. I normally use black enamel intended for agricultural use.
-
Jhonno
- Homo Hair
- Posts: 20362
- Joined: Mon Jan 10, 2005 11:00 pm
- Location: FLAT, FLAT, FLAT!!
POR15
-
Jozi
- E30 Zone Addict

- Posts: 3076
- Joined: Thu Nov 22, 2007 11:00 pm
- Location: Dublin, Ireland
I agree with this, I painted up parts with hammerite and the slightest knock makes it chip. Their primer on the other hand seemed to hold up well!Brianmoooore wrote:Wouldn't recommend Hammerite for car applications. It has to be laid on in extremely thick layers and is very brittle and easily chipped as a result. I normally use black enamel intended for agricultural use.
Knotted wirewheel for cleaning
-
Grrrmachine
- E30 Zone Wiki / Team Member

- Posts: 8043
- Joined: Sat Feb 09, 2008 11:00 pm
- Location: Warsaw, Poland
I'll switch to the grinder then. And I've picked up some enamel paint for metal, so I'll give that a go.
It doesn't need to be pretty, it just needs to stop the winter salt eating away any more of my car
It doesn't need to be pretty, it just needs to stop the winter salt eating away any more of my car
'89 325i Touring | Touring Resto Thread | In-Dash Screen install
-
Jhonno
- Homo Hair
- Posts: 20362
- Joined: Mon Jan 10, 2005 11:00 pm
- Location: FLAT, FLAT, FLAT!!
POR15 as my post above. Rock 'ard innit.
-
Grrrmachine
- E30 Zone Wiki / Team Member

- Posts: 8043
- Joined: Sat Feb 09, 2008 11:00 pm
- Location: Warsaw, Poland
Can't get it over here though Jhonno. If it's got a brand name, I can't get it.
'89 325i Touring | Touring Resto Thread | In-Dash Screen install
-
DanThe
- E30 Zone Team Member

- Posts: 28649
- Joined: Sat Sep 10, 2005 11:00 pm
- Location: Staffs
If your not going to go through proper paint stages with decent (expensive) gear then you may as well just wire brush it all by hand and bang a load of waxoil on. It will stop any rusting that is going on and keep water out of all other areas. Removing the coating down to bare metal is a bad move if your not going to replace it properly.
-
bigbird76
- E30 Zone Regular

- Posts: 571
- Joined: Sat Feb 16, 2008 11:00 pm
- Location: Swansea Wales UK
POR 15 here also







Leigh







Leigh
-
Grrrmachine
- E30 Zone Wiki / Team Member

- Posts: 8043
- Joined: Sat Feb 09, 2008 11:00 pm
- Location: Warsaw, Poland
All good info, cheers guys. I've attacked it with the angle gringer/knot brush, but not to the point of removing all the existing coating; just the scabs and pimples where the rust has taken hold. Then things got a wipe down with degreaser, and then slapping on this enamel stuff; thinned a little because it's so cold here at the moment (minus 12!)
So we'll see how it holds. Not a pro job, but can't be worse than leaving the rust to fester.
So we'll see how it holds. Not a pro job, but can't be worse than leaving the rust to fester.
'89 325i Touring | Touring Resto Thread | In-Dash Screen install


