Hi I have got a 92 320i convertible aand was thinking of putting the 325i engine in.
How difficult is it?
I assume engine mounts, subframe etc are all the same, but is the wiring loom, ecu and gearbox different and are they and modifications required?
Thanks very much
Matt
engine swap
Moderator: martauto
-
matt86
- E30 Zone Addict

- Posts: 2468
- Joined: Thu Jan 19, 2012 11:00 pm
- Location: "The Cotswolds" Stroud, Gloucestershire
-
maxfield
- Old Skooler

- Posts: 15185
- Joined: Sat Nov 26, 2005 11:00 pm
- Location: Mansfield
Looms are the same. Ecu's are different.
You can put a 2.5 on the 2.0 box but they're not as strong. Although I'm assuming you'll be leaving the engine standard then it should hold up.
As for mounting. Straight in.
Do a search been convered a lot.
You can put a 2.5 on the 2.0 box but they're not as strong. Although I'm assuming you'll be leaving the engine standard then it should hold up.
As for mounting. Straight in.
Do a search been convered a lot.

-
Ajsingh
- E30 Zone Addict

- Posts: 2378
- Joined: Sun Mar 28, 2010 11:00 pm
- Location: West Laaaandaan init! / Milton Keynes
Im running a 2.7 on a 2.0 gearbox, 10,000 miles later and its going good.
E30 Crazy!
-
capri_rob
- Married to the E30 Zone

- Posts: 9678
- Joined: Tue Feb 19, 2008 11:00 pm
- Location: South Staffordshire
As long as you get a facelift 325i donk its about the easiest swap you can do.
Almost certain you will need to swap to the 325i exhaust too though.
Good luck
Almost certain you will need to swap to the 325i exhaust too though.
Good luck

e30topless said : Proper BMW's have 4 headlights, last of the run was the E30 and E34/E32 anything after that is just complete shite
-
matt86
- E30 Zone Addict

- Posts: 2468
- Joined: Thu Jan 19, 2012 11:00 pm
- Location: "The Cotswolds" Stroud, Gloucestershire
Just out of curiosity I though the 2.5 was the largest engine in the e30's apart from the m3, how do you get a 2.7 is that rebored?
Can you do a powerplant conversion like with the corrado and golf I had I had a 2 litre block with a 1.8 head and they went really well, could you do something similar with a e30 block?
What's the best way to get more power without getting overly complicated, I believe the 325i is 171 bhp standard, so could you put a performance cam in and induction kit and acheive around 190 bhp? If you were to do this would it idle lumpy and put the timing out?
Thanks to all for the advice very much!
Matt
Can you do a powerplant conversion like with the corrado and golf I had I had a 2 litre block with a 1.8 head and they went really well, could you do something similar with a e30 block?
What's the best way to get more power without getting overly complicated, I believe the 325i is 171 bhp standard, so could you put a performance cam in and induction kit and acheive around 190 bhp? If you were to do this would it idle lumpy and put the timing out?
Thanks to all for the advice very much!
Matt
-
ross2009
- E30 Zone Addict

- Posts: 2762
- Joined: Mon Nov 19, 2007 11:00 pm
- Location: In my beemer MAN !!!! st neots CAMBS
bmw made there engines pretty much spot on as they are
a 2.7 is what they used in the alpina models and is made up from a eta or the m21 2.4 diesel crank 2 ltr rods 2.5 pistons and a 2.5 head you can even push it to a 3 ltr
yeah a good exhaust a cam maybe and a good chip will give you about 190 200 bhp
have a read
http://en.wikipedia.org/wiki/BMW_M20
a 2.7 is what they used in the alpina models and is made up from a eta or the m21 2.4 diesel crank 2 ltr rods 2.5 pistons and a 2.5 head you can even push it to a 3 ltr
yeah a good exhaust a cam maybe and a good chip will give you about 190 200 bhp
have a read
http://en.wikipedia.org/wiki/BMW_M20
-
matt86
- E30 Zone Addict

- Posts: 2468
- Joined: Thu Jan 19, 2012 11:00 pm
- Location: "The Cotswolds" Stroud, Gloucestershire
Oh right that's interesting, might keep it simple for now and put the 2.5 engine in, stainless manifold, performance camshaft and a induction kit.
Thanks
Matt
Thanks
Matt
-
ross2009
- E30 Zone Addict

- Posts: 2762
- Joined: Mon Nov 19, 2007 11:00 pm
- Location: In my beemer MAN !!!! st neots CAMBS
indunction kit dont do crap mate stick with the air box
-
Grrrmachine
- E30 Zone Wiki / Team Member

- Posts: 8043
- Joined: Sat Feb 09, 2008 11:00 pm
- Location: Warsaw, Poland
Our own wiki has more info on M20 Upgrades:
http://www.e30zone.net/e30zonewiki/inde ... n_Upgrades
As has been mentioned, forget an induction kit. And don't get any old manifold, there's only one out there that's worth fitting, and it's the BTB. And if you're going to fit a cam, you'll have to chip the system to match.
http://www.e30zone.net/e30zonewiki/inde ... n_Upgrades
As has been mentioned, forget an induction kit. And don't get any old manifold, there's only one out there that's worth fitting, and it's the BTB. And if you're going to fit a cam, you'll have to chip the system to match.
'89 325i Touring | Touring Resto Thread | In-Dash Screen install
-
ross2009
- E30 Zone Addict

- Posts: 2762
- Joined: Mon Nov 19, 2007 11:00 pm
- Location: In my beemer MAN !!!! st neots CAMBS
and the btb iant cheap i can tell ya 

