Removing trailing arm bushes

Need technical Q/A then you're in the right place

Moderator: martauto

Grrrmachine
E30 Zone Wiki / Team Member
E30 Zone Wiki / Team Member
Posts: 8043
Joined: Sat Feb 09, 2008 11:00 pm
Location: Warsaw, Poland

Post Sat Jan 14, 2012 1:05 pm

Anyone got some sneaky tips? I've tried the puller method in the wiki:

http://www.e30zone.net/e30zonewiki/inde ... hes#Bushes

and all I did was strip the thread from the threaded bar; the bushes are locked in there tight. Can't really burn them out either, since they're still in situ under the fuel tank.

Advice?
daimlerman
**BANNED**
Posts: 15968
Joined: Mon Feb 27, 2006 11:00 pm
Location: Grumpy Old Man

Post Sat Jan 14, 2012 2:04 pm

Image
Grrrmachine
E30 Zone Wiki / Team Member
E30 Zone Wiki / Team Member
Posts: 8043
Joined: Sat Feb 09, 2008 11:00 pm
Location: Warsaw, Poland

Post Sat Jan 14, 2012 3:02 pm

Grrrmachine wrote:Can't really burn them out either, since they're still in situ under the fuel tank.
but I knew that picture would turn up again!

I've sort of found a solution; those inch-long nuts that are usually used to join threaded bar together. But I've now snapped three lengths of threaded rod drawing out two bushes; these buggers are wedged in tight!
User avatar
Prey
E30 Zone Regular
E30 Zone Regular
Posts: 359
Joined: Tue Jun 15, 2010 11:00 pm
Location: M1 J28

Post Sat Jan 14, 2012 3:10 pm

admittedly don't know if you can do this in situ or not but if you can get a cordless drill into them just stick a small bit on and drill a few holes thru the bush to loosen it a little - then i had no probs pulling mine out with a bit of m10 rod and a deep 30mm socket. i hate burning them it's filthy, smelly, antisocial, etc etc.
DanThe
E30 Zone Team Member
E30 Zone Team Member
Posts: 28649
Joined: Sat Sep 10, 2005 11:00 pm
Location: Staffs

Post Sat Jan 14, 2012 8:10 pm

The easiest way by far is to heat them up, you could use the hole-saw method though, once the steel sleeve is out the way its easy to push the rubber out
User avatar
Mikey_Boy
E30 Zone Regular
E30 Zone Regular
Posts: 996
Joined: Sun Mar 16, 2008 11:00 pm
Location: Cheshire - trying to avoid the bling!

Post Sat Jan 14, 2012 8:19 pm

^^^

+1 :thumb:

I ended up cutting pretty much all of mine out when I converted to polybushes...

It is a sh*t of a job - good luck!
User avatar
redcar
E30 Zone Squatter
E30 Zone Squatter
Posts: 1610
Joined: Wed Jul 20, 2011 11:00 pm
Location: Hertfordshire

Post Sat Jan 14, 2012 8:30 pm

Smack it the sleeve real hard with hammer and screwdriver

It will slip out in one piece

Atleast mine did.
daimlerman
**BANNED**
Posts: 15968
Joined: Mon Feb 27, 2006 11:00 pm
Location: Grumpy Old Man

Post Sat Jan 14, 2012 9:20 pm

Grrrmachine wrote:
Grrrmachine wrote:Can't really burn them out either, since they're still in situ under the fuel tank.
but I knew that picture would turn up again!

I've sort of found a solution; those inch-long nuts that are usually used to join threaded bar together. But I've now snapped three lengths of threaded rod drawing out two bushes; these buggers are wedged in tight!
Thing is,you need to remove the trailing arm!
Then with it dropped out of the way,if you are to lazy to un-bolt the halfshaft,you have ample safe clearance to burn the bloody bushes out.Replace with polybushes,BTW,as the axle carrier/diff mount are rubber,no harshness is carried into the cabin and you gain from the permanent 'new bush' feeling.....
Grrrmachine
E30 Zone Wiki / Team Member
E30 Zone Wiki / Team Member
Posts: 8043
Joined: Sat Feb 09, 2008 11:00 pm
Location: Warsaw, Poland

Post Sat Jan 14, 2012 9:25 pm

Lazy :D

The subframe's out, the diff is off, the trailing arms are on the floor with the half-shafts attached. The only thing I haven't disconnected is the handbrake cables, because I hate working on that poxy little tooth wheel through the brake disc. So they're still under the car.

I got two of the foockers out, then broke another length of threaded rod trying to get a new one back in. I even resorted to sex lube to try and get them moving, but I guess Durex Play lotion is as rubbish on cars as it was in the bedroom!
SGP
E30 Zone Regular
E30 Zone Regular
Posts: 502
Joined: Thu Aug 31, 2006 11:00 pm

Post Sat Jan 14, 2012 9:30 pm

I held them (with a helper) in a good bench vice and used 2 sockets 1 big one for the bush to slide into and a smaller one to push it through. Only took about a half hour. Well chuffed.
If it ain't broke..
Fix it till it is :)