seat mechanism trouble
Moderator: martauto
-
Cloggy Saint
- Old Skooler

- Posts: 8027
- Joined: Sun Jan 09, 2005 11:00 pm
- Location: zummerzet
My driver's seat has a problem in that when I recline the seat back it doesn't always catch and it springs back to the fully forward position. I've swapped the mechanism but that makes no difference. I assume then that it's something to do with the flat bar that connects the left and right mechanisms but what can go wrong with this? 
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
Usual cause is a broken seat frame, in turn as a result of one of the seat back securing screws working loose.
-
Cloggy Saint
- Old Skooler

- Posts: 8027
- Joined: Sun Jan 09, 2005 11:00 pm
- Location: zummerzet
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
How are you sure?
-
Cloggy Saint
- Old Skooler

- Posts: 8027
- Joined: Sun Jan 09, 2005 11:00 pm
- Location: zummerzet
-
Sanchez
- Married to the E30 Zone

- Posts: 7578
- Joined: Sun Apr 17, 2005 11:00 pm
- Location: Sunny Scotland
Is it back together properly then?
-
Cloggy Saint
- Old Skooler

- Posts: 8027
- Joined: Sun Jan 09, 2005 11:00 pm
- Location: zummerzet
-
Duke137
- Married to the E30 Zone

- Posts: 7207
- Joined: Sat Aug 29, 2009 11:00 pm
watching this, my passenger seat does this....
How do you pronounce 'either'? I say 'either', but some say 'either'. Either is correct.
-
Tay
- E30 Zone Regular

- Posts: 343
- Joined: Mon Feb 06, 2006 11:00 pm
sometimes the handle doesn't return to the correct position due to th bolster pressing against it! when you recline it before you let go make sure the handle is in the right position???
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
How much of the mech. have you had apart? Have you had the press in bits in the centre of the mech, that transmit the lever's action from one side of the seat to the other, off? Have you had the whole latch assemblies off?
-
Cloggy Saint
- Old Skooler

- Posts: 8027
- Joined: Sun Jan 09, 2005 11:00 pm
- Location: zummerzet
I just removed the entire mechanism assemblies from both sides and replaced them with known good units. When I lift the recline lever the flat bar lifts and the seat back moves but I have to then push the lever down in order to make it bite, and even that doesn't always work.
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
Why did you replace them? To cure the same fault? If everything is put back correctly, the problem can only be a bent frame if it's not broken.
Take the seat back off, check that both of the spikes that the back sits on are latched by the tilt mechanism, and then carefully place the seat back on the spikes. Both sides should slide in easily and completely, without putting any twist on the spikes.
Take the seat back off, check that both of the spikes that the back sits on are latched by the tilt mechanism, and then carefully place the seat back on the spikes. Both sides should slide in easily and completely, without putting any twist on the spikes.
-
Cloggy Saint
- Old Skooler

- Posts: 8027
- Joined: Sun Jan 09, 2005 11:00 pm
- Location: zummerzet
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
Do both sides work reliably, independently of each other, if the back is off?
-
Cloggy Saint
- Old Skooler

- Posts: 8027
- Joined: Sun Jan 09, 2005 11:00 pm
- Location: zummerzet
-
Brianmoooore
- E30 Zone Team Member

- Posts: 49360
- Joined: Mon Jan 10, 2005 11:00 pm
It's not the whole latch assembly turning, is it? Are the spring loaded catches that locate them engaged?
-
Cloggy Saint
- Old Skooler

- Posts: 8027
- Joined: Sun Jan 09, 2005 11:00 pm
- Location: zummerzet
I've decided the fact that the mechanisms are bone dry probably isn't helping things, it's a laboured process for the lever to return to it's starting point. Would good old fashioned grease get things moving again or is there something better out there?

